Skip to contentSkip to conversation

Kexec failled with igb-1.2.45-K2 network driver

DISCUSSION Thierry Iceta 2 participants 2 messages Feb 27, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

Hi

Using kexec as indicated hereunder I am enable to use ethernet network directly after kexec boot
due to I suppose last igb driver "igb-1.2.45-K2"
Only solution found is to rmmod igb and just after modprobe igb

Coul you tell me the kexec version that take into account the driver igb-1.2.45-K2?
May be an other solution is to tell kexec to load this modules ? but how ?

any help will be appreciated
Thanks in advance
Thierry
HW=X86_64
SW=redhat (kernel 2.6.18-122)
kexec used par Rhel5 ==>kexec-tools-1.102pre-56.el5 ==>KO kerxec tested ==>kexec-tools-2.0.0-7.fc11.x86_64.rpm ==>KO

kexec_append="root=LABEL=/ ro ro root=LABEL=/ console=tty0
console=ttyS1,115200"
export $kexec_append
kexec --force --append="$kexec_append" --initrd=/a/boot/initrd-2.6.18-122.el5.img --args-linux /a/boot/vmlinuz-2.6.18-122.el5

Signature · 16 lines
  __________________________________________________________________        
                  Bull, Architect of an Open World TM
                    	 Open Software R&D

        Email   :[email protected]
        Bull SA                Bullcom :229 76 29
        1, rue de Provence     Phone   :+33 04 76 29 76 29
        B.P. 208               http://www.bull.com                          
        38432 Echirolles-CEDEX Office  :FREC B1-361 
  __________________________________________________________________        


_______________________________________________
kexec mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/kexec
#1 lore raw
Quoted 19 lines · Thierry Iceta

Hi

Using kexec as indicated hereunder I am enable to use ethernet network directly after kexec boot
due to I suppose last igb driver "igb-1.2.45-K2"
Only solution found is to rmmod igb and just after modprobe igb

Coul you tell me the kexec version that take into account the driver igb-1.2.45-K2?
May be an other solution is to tell kexec to load this modules ? but how ?

any help will be appreciated
Thanks in advance
Thierry
HW=X86_64
SW=redhat (kernel 2.6.18-122)
kexec used par Rhel5 ==>kexec-tools-1.102pre-56.el5 ==>KO kerxec tested ==>kexec-tools-2.0.0-7.fc11.x86_64.rpm ==>KO

Quoted 7 lines

kexec_append="root=LABEL=/ ro ro root=LABEL=/ console=tty0
console=ttyS1,115200"
export $kexec_append
kexec --force --append="$kexec_append" --initrd=/a/boot/initrd-2.6.18-122.el5.img --args-linux /a/boot/vmlinuz-2.6.18-122.el5

Sounds like something has gone bad in the driver in resetting the NIC. If you open a bug at bugzilla.redhat.com, I'll pick it up and look at it. Neil

Quoted 18 lines
Signature · 16 lines
  __________________________________________________________________        
                  Bull, Architect of an Open World TM
                    	 Open Software R&D

        Email   :[email protected]
        Bull SA                Bullcom :229 76 29
        1, rue de Provence     Phone   :+33 04 76 29 76 29
        B.P. 208               http://www.bull.com                          
        38432 Echirolles-CEDEX Office  :FREC B1-361 
  __________________________________________________________________        


_______________________________________________
kexec mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/kexec

_______________________________________________
kexec mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/kexec