Skip to contentSkip to conversation

How can PCI resource allocation fail?

DISCUSSION Christian P. Schmidt 5 participants 5 messages Mar 12, 2009 – Mar 13, 2009

lore
Share & tools
lore
#0 lore raw

Hi all,

I'm toying with the alsa-driver for the Creative Labs X-Fi. I'm working on the PCI Express version of this card, though, which is the same as the PCI version plus a PCIe to PCI bridge but has a different ID:

          +-1c.2-[0000:03-04]----00.0-[0000:04]----00.0  1102:0009

03:00.0 PCI bridge: Creative Labs Device 7006
04:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG

Now, after adding the ID, the driver fails:

[46833.487579] CA0106 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[46833.487586] CA0106 0000:04:00.0: PCI INT A disabled
[46833.487588] cannot allocate the port
[46833.487594] CA0106: probe of 0000:04:00.0 failed with error -16

The actual error is occurring in

	chip->port = pci_resource_start(pci, 0);
	chip->res_port = request_region(chip->port, pci_resource_len(pci,0), "snd_ca0106");
	if (!chip->res_port) {
		snd_ca0106_free(chip);
		printk(KERN_ERR "cannot allocate the port\n");
		return -EBUSY;
	}

This from /proc/iomem:

f9f00000-f9ffffff : PCI Bus 0000:03
f9f00000-f9ffffff : PCI Bus 0000:04

    f9ffc000-f9ffffff : 0000:04:00.0

Some additional debug output tells me that the code is actually trying to allocate 16k starting from f9ffc000. What could be potential reasons for the failure? Do I have to do something with the bridge before I can try to request the region?

Regards,
Christian

PS: lcpci -vv output afterwards, can't see anything special here.

03:00.0 PCI bridge: Creative Labs Device 7006 (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=03, secondary=04, subordinate=04, sec-latency=64
Memory behind bridge: f9f00000-f9ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Mask- 64bit+ Count=1/16 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Creative Labs Device 0010
Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-

04:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG
Subsystem: Creative Labs Device 0018
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f9ffc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [dc] Power Management version 3
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: snd-ca0106

#1 lore raw
Quoted 27 lines · Christian P. Schmidt

Hi all,

I'm toying with the alsa-driver for the Creative Labs X-Fi. I'm working on the PCI Express version of this card, though, which is the same as the PCI version plus a PCIe to PCI bridge but has a different ID:

          +-1c.2-[0000:03-04]----00.0-[0000:04]----00.0  1102:0009

03:00.0 PCI bridge: Creative Labs Device 7006
04:00.0 Audio device: Creative Labs [SB X-Fi Xtreme Audio] CA0110-IBG

Now, after adding the ID, the driver fails:

[46833.487579] CA0106 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[46833.487586] CA0106 0000:04:00.0: PCI INT A disabled
[46833.487588] cannot allocate the port
[46833.487594] CA0106: probe of 0000:04:00.0 failed with error -16

The actual error is occurring in

	chip->port = pci_resource_start(pci, 0);
	chip->res_port = request_region(chip->port, pci_resource_len(pci,0), "snd_ca0106");
	if (!chip->res_port) {
		snd_ca0106_free(chip);
		printk(KERN_ERR "cannot allocate the port\n");
		return -EBUSY;
	}
Quoted 8 lines

This from /proc/iomem:

f9f00000-f9ffffff : PCI Bus 0000:03
f9f00000-f9ffffff : PCI Bus 0000:04

    f9ffc000-f9ffffff : 0000:04:00.0

Some additional debug output tells me that the code is actually trying to allocate 16k starting from f9ffc000. What could be potential reasons for the failure? Do I have to do something with the bridge before I can try to request the region?

request_region is requesting IO ports. The PCI BAR on the card is MMIO memory, not IO ports, so request_mem_region has to be used. It's possible that this driver isn't set up to handle MMIO space.

#2 lore raw
In reply to Christian P. Schmidt
Quoted 2 lines · Christian P. Schmidt

I'm toying with the alsa-driver for the Creative Labs X-Fi. I'm working on the PCI Express version of this card,

... which isn't supported ...

Quoted 4 lines
[46833.487588] cannot allocate the port
[46833.487594] CA0106: probe of 0000:04:00.0 failed with error -16
...
	Region 0: Memory at f9ffc000 (32-bit, non-prefetchable) [size=16K]

... because this I/O range is memory-mapped; the driver knows only about models with regular I/O ports. (This has nothing to do with the PCI-E bridge; the X-Fi chip itself is a different model.)

Best regards,
Clemens

#3 lore raw

At Fri, 13 Mar 2009 08:44:26 +0100,

Quoted 6 lines · Clemens Ladisch
Quoted 2 lines · Christian P. Schmidt

I'm toying with the alsa-driver for the Creative Labs X-Fi. I'm working on the PCI Express version of this card,

... which isn't supported ...

You can try sound-unstable tree. If your device is a Vista-compatible model, it may work with snd-hda-intel (with a luck).

git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-unstable-2.6.git

The corresponding alsa-driver snapshot is:
ftp://ftp.kernel.org/pub/linux/kernel/people/tiwai/snapshot/alsa-driver-unstable-snapshot.tar.gz

If it's no Vista-compatible (i.e. HD-audio compatible) model, you can try topic/sbxfi branch of the sound unstable tree above. Just pull/merge the branch after cloning.

Takashi

#4 lore raw
Quoted 22 lines · Takashi Iwai

At Fri, 13 Mar 2009 08:44:26 +0100,

Quoted 6 lines · Clemens Ladisch
Quoted 2 lines · Christian P. Schmidt

I'm toying with the alsa-driver for the Creative Labs X-Fi. I'm working on the PCI Express version of this card,

... which isn't supported ...

You can try sound-unstable tree.  If your device is a Vista-compatible model, it may work with snd-hda-intel (with a luck).

  git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-unstable-2.6.git

The corresponding alsa-driver snapshot is:
  ftp://ftp.kernel.org/pub/linux/kernel/people/tiwai/snapshot/alsa-driver-unstable-snapshot.tar.gz

If it's no Vista-compatible (i.e. HD-audio compatible) model, you can try topic/sbxfi branch of the sound unstable tree above.  Just pull/merge the branch after cloning.

Quoted 6 lines

Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

IIRC, all PCI-E X-Fi cards are UAA (this part I'm pretty certain about), and all UAA X-Fi cards are PCI-E (I saw at some point some OEM X-Fi card that had two chips, one on the front and other on the rear, so not totally sure about this one).

Vedran
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel