Skip to contentSkip to conversation

multipath question

linux-lvm vu pham 2 participants 3 messages Mar 19, 2009 – Mar 20, 2009

lore
Share & tools
lore

vu pham

author
#0 lore raw

I set up multipath on /dev/sda and /dev/sdb which are mapped from a remote single disk, which has two partitions.

Below are some output.
[root@vm5 mpath]# ls -l
total 0
lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0 -> ../dm-2 lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0p1 -> ../dm-3 lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0p2 -> ../dm-4

[root@vm5 mpath]# multipath -ll
mpath0 (16465616462656166313a3100000000000000000000000000) dm-2 IET,VIRTUAL-DISK [size=5.0G][features=0][hwhandler=0]
\_ round-robin 0 [prio=0][active]
\_ 0:0:0:1 sda 8:0 [active][ready]
\_ round-robin 0 [prio=0][enabled]
\_ 1:0:0:1 sdb 8:16 [active][ready]
[root@vm5 mpath]#

From the multipath command, I know dm-2 is mapped from two devices /dev/sda and /dev/sdb as expected.

But how can I know if dm-3 is mapped from /dev/sda1 and /dev/sdb1, and dm-4 from /dev/sda2 and /dev/sdb2 ?

The command "multipath -ll" only gives info on mpath0 or dm-2.

I tried multipath -ll /dev/mpath/mpath0p1 but does not show anything.

Thanks,

Vu

#1 lore raw
Quoted 24 lines · vu pham

I set up multipath on /dev/sda and /dev/sdb which are mapped from a remote single disk, which has two partitions.

Below are some output.
[root@vm5 mpath]# ls -l
total 0
lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0 -> ../dm-2 lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0p1 -> ../dm-3 lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0p2 -> ../dm-4

[root@vm5 mpath]# multipath -ll
mpath0 (16465616462656166313a3100000000000000000000000000) dm-2 IET,VIRTUAL-DISK
[size=5.0G][features=0][hwhandler=0]
\_ round-robin 0 [prio=0][active]
\_ 0:0:0:1 sda 8:0 [active][ready]
\_ round-robin 0 [prio=0][enabled]
\_ 1:0:0:1 sdb 8:16 [active][ready]
[root@vm5 mpath]#

From the multipath command, I know dm-2 is mapped from two devices
/dev/sda and /dev/sdb as expected.

Quoted 6 lines

But how can I know if dm-3 is mapped from /dev/sda1 and /dev/sdb1, and dm-4 from /dev/sda2 and /dev/sdb2 ?

The command "multipath -ll" only gives info on mpath0 or dm-2.

I tried multipath -ll /dev/mpath/mpath0p1 but does not show anything.

mpath0 is analogous to sda and mpath0p1, mpath0p2 are analogous to sda1, sda2.

since there is "mpath0" in mpath0p1 and mpath0p2, you can be sure that they are built off sda and sdb (in effect mpath0p1 is made of sda1 and sdb1 and so on)...

Quoted 10 lines

Thanks,

Vu

_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

author
#2 lore raw
Quoted 27 lines · Chandra Seetharaman
Quoted 26 lines · vu pham

I set up multipath on /dev/sda and /dev/sdb which are mapped from a remote single disk, which has two partitions.

Below are some output.
[root@vm5 mpath]# ls -l
total 0
lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0 -> ../dm-2 lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0p1 -> ../dm-3 lrwxrwxrwx 1 root root 7 Mar 19 10:34 mpath0p2 -> ../dm-4

[root@vm5 mpath]# multipath -ll
mpath0 (16465616462656166313a3100000000000000000000000000) dm-2 IET,VIRTUAL-DISK [size=5.0G][features=0][hwhandler=0]
\_ round-robin 0 [prio=0][active]
\_ 0:0:0:1 sda 8:0 [active][ready]
\_ round-robin 0 [prio=0][enabled]
\_ 1:0:0:1 sdb 8:16 [active][ready]
[root@vm5 mpath]#

From the multipath command, I know dm-2 is mapped from two devices
/dev/sda and /dev/sdb as expected.

But how can I know if dm-3 is mapped from /dev/sda1 and /dev/sdb1, and dm-4 from /dev/sda2 and /dev/sdb2 ?

The command "multipath -ll" only gives info on mpath0 or dm-2.

Quoted 9 lines
Quoted 1 line

I tried multipath -ll /dev/mpath/mpath0p1 but does not show anything.

mpath0 is analogous to sda and mpath0p1, mpath0p2 are analogous to sda1, sda2.

since there is "mpath0" in mpath0p1 and mpath0p2, you can be sure that they are built off sda and sdb (in effect mpath0p1 is made of sda1 and sdb1 and so on)...

Chandra, that makes sense. Thanks a lot for your explanation.

Vu