sht15 humidity sensor driver
PATCH 1/1 sht15 humidity sensor driver
From: Jonathan Cameron <[email protected]>
hwmon: SHT15 and similar Sensiron humidity sensors
---
Changes made as suggested by Andrew Morton (thanks!)
1) replaced IRQ_GPIO calls with gpio_to_irq
2) clean up of error code
3) cleanup of comments so those that claim to be kernel-doc actually are.
Depends on:
Regulator: Push lock out of _notifier_call_chain + add voltage change event. 87986cd8bc1d7523a31f28b0e41949fcc34eff78
in voltage/for-next
Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf
These sensors communicate over a 2 wire bus running a device specific protocol. The complexity of the driver is mainly due to handling the substantial delays between requesting a reading and the device pulling the data line low to indicate that the data is available. This is handled by an interrupt that is disabled under all other conditions.
I wasn't terribly clear on the best way to handle this, so comments on that aspect would be particularly welcome!
Interpretation of the temperature depends on knowing the supply voltage. If configured in a board config as a regulator consumer this is obtained from the regulator subsystem. If not it should be provided in the platform data.
I've placed this driver in the hwmon subsystem as it is definitely a device that may be used for hardware monitoring and with it's relatively slow response times (up to 120 millisecs to get a reading) a caching strategy certainly seems to make sense!
---
drivers/hwmon/Kconfig +10 -0
@@ -635,6 +635,16 @@ config SENSORS_PC87427 This driver can also be built as a module. If so, the module will be called pc87427. +config SENSORS_SHT15 + tristate "Sensiron humidity and temperature sensors. SHT15 and compat." + depends on GENERIC_GPIO + help + If you say yes here you get support for the Sensiron SHT10, SHT11, + SHT15, SHT71, SHT75 humidity and temperature sensors. + + This driver can also be built as a module. If so, the module + will be called sht15. + config SENSORS_SIS5595 tristate "Silicon Integrated Systems Corp. SiS5595" depends on PCI
drivers/hwmon/Makefile +1 -0
@@ -70,6 +70,7 @@ obj-$(CONFIG_SENSORS_MAX1619) += max1619.o obj-$(CONFIG_SENSORS_MAX6650) += max6650.o obj-$(CONFIG_SENSORS_PC87360) += pc87360.o obj-$(CONFIG_SENSORS_PC87427) += pc87427.o +obj-$(CONFIG_SENSORS_SHT15) += sht15.o obj-$(CONFIG_SENSORS_SIS5595) += sis5595.o obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o obj-$(CONFIG_SENSORS_SMSC47M1) += smsc47m1.o
drivers/hwmon/sht15.c new file +692 -0
692 lines not on this page · raw message
include/linux/sht15.h new file +24 -0
@@ -0,0 +1,24 @@ +/* +* sht15.h - support for the SHT15 Temperature and Humidity Sensor +* +* Copyright (c) 2009 Jonathan Cameron +* +* Copyright (c) 2007 Wouter Horre +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +/** +* struct sht15_platform_data - sht15 connectivity info +* @gpio_data: no. of gpio to which bidirectional data line is connected +* @gpio_sck: no. of gpio to which the data clock is connected. +* @supply_mv: supply voltage in mv. Overridden by regulator if available. +**/ +struct sht15_platform_data { +int gpio_data; +int gpio_sck; +int supply_mv; +}; +
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors