cmd_mmc: add support device command for selecting mmc device (resend)
PATCH 1/1 cmd_mmc: add support device command for selecting mmc device (resend)
This patch improves device command for selecting mmc device
Signed-off-by Minkyu Kang <[email protected]>
--- common/cmd_mmc.c | 61 +++++++++++++++++++++++++++++++++++++++++++++++++---- 1 files changed, 56 insertions(+), 5 deletions(-)
common/cmd_mmc.c +56 -5
@@ -26,19 +26,70 @@#include <mmc.h> #ifndef CONFIG_GENERIC_MMC +int curr_device =-1 ; +int do_mmc (cmd_tbl_t *cmdtp,int flag,int argc,char *argv[]) { -if (mmc_legacy_init (1 ) !=0 ) { -printf ("No MMC card found\n" ); +int dev; + +if (argc <2 ) { +cmd_usage (cmdtp);return 1 ; } + +if (strcmp (argv[1 ],"init" ) ==0 ) { +if (argc ==2 ) { +if (curr_device <0 ) + dev =1 ; +else + dev = curr_device; + }else if (argc ==3 ) { + dev = (int )simple_strtoul (argv[2 ],NULL ,10 ); + }else { +cmd_usage (cmdtp); +return 1 ; + } + +if (mmc_legacy_init (dev) !=0 ) { +puts ("No MMC card found\n" ); +return 1 ; + } + + curr_device = dev; +printf ("mmc%d is available\n" , curr_device); + }else if (strcmp (argv[1 ],"device" ) ==0 ) { +if (argc ==2 ) { +if (curr_device <0 ) { +puts ("No MMC device available\n" ); +return 1 ; + } + }else if (argc ==3 ) { + dev = (int )simple_strtoul (argv[2 ],NULL ,10 ); + +#ifdef CONFIG_SYS_MMC_SET_DEV +if (mmc_set_dev (dev) !=0 ) +return 1 ; +#endif + curr_device = dev; + }else { +cmd_usage (cmdtp); +return 1 ; + } + +printf ("mmc%d is current device\n" , curr_device); + }else { +cmd_usage (cmdtp); +return 1 ; + } +return 0 ; }U_BOOT_CMD ( - mmcinit,1 ,0 , do_mmc, -"init mmc card" , -NULL + mmc,3 ,1 , do_mmc, +"MMC sub-system" , +"init [dev] - init MMC sub system\n" +"mmc device [dev] - show or set current device\n" );#else /* !CONFIG_GENERIC_MMC */
Wolfgang Denk
AppliedPATCH 1/1 cmd_mmc: add support device command for selecting mmc device (resend)
Dear Minkyu Kang,
Quoted 6 lines · In message <[email protected]> you wrote:
This patch improves device command for selecting mmc device
Signed-off-by Minkyu Kang <[email protected]>--- common/cmd_mmc.c | 61 +++++++++++++++++++++++++++++++++++++++++++++++++---- 1 files changed, 56 insertions(+), 5 deletions(-)
Applied, thanks.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "Any excuse will serve a tyrant." - Aesop