Skip to contentSkip to conversation

Move an array/volgroup to another machine.

linux-lvm Gerry Reno 3 participants 7 messages Apr 16, 2009 – Apr 17, 2009

lore
Share & tools
lore

Gerry Reno

author
#0 lore raw

We built a replacement server (x86_64) for an older server (x86). Now we want to move a RAID-5 array intact from the older machine over to the new machine. We know the UUID of the array and of all the PV and VG on the array. So what commands should we perform after plugging in all the array drives to the new server to bring up the array and lvm on the new machine?

Regards,
Gerry

#1 lore raw
Quoted 1 line · Gerry Reno

We built a replacement server (x86_64) for an older server (x86). Now we want to move a RAID-5 array intact from the older machine over to the new machine. We know the UUID of the array and of all the PV and VG on the array. So what commands should we perform after plugging in all the array drives to the new server to bring up the array and lvm on the new machine?

"vgscan" and "vgchange -a VGNAME" I believe.

Make sure your VG name doesn't conflict with any already in the machine.

Quoted 9 lines

Regards,
Gerry

_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

#2 lore raw
Quoted 4 lines · Eric Brunson
Quoted 1 line · Gerry Reno

We built a replacement server (x86_64) for an older server (x86). Now we want to move a RAID-5 array intact from the older machine over to the new machine. We know the UUID of the array and of all the PV and VG on the array. So what commands should we perform after plugging in all the array drives to the new server to bring up the array and lvm on the new machine?

"vgscan" and "vgchange -a VGNAME" I believe.

Sorry, doing three things at once: vgchange -a y VGNAME

Quoted 18 lines

Make sure your VG name doesn't conflict with any already in the machine.

Quoted 9 lines

Regards,
Gerry

_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

author
#3 lore raw
Quoted 13 lines · Eric Brunson
Quoted 4 lines · Eric Brunson
Quoted 1 line · Gerry Reno

We built a replacement server (x86_64) for an older server (x86). Now we want to move a RAID-5 array intact from the older machine over to the new machine. We know the UUID of the array and of all the PV and VG on the array. So what commands should we perform after plugging in all the array drives to the new server to bring up the array and lvm on the new machine?

"vgscan" and "vgchange -a VGNAME" I believe.

Sorry, doing three things at once: vgchange -a y VGNAME

Quoted 3 lines

Make sure your VG name doesn't conflict with any already in the machine.

Will vgchange activate the raid array?

The new server just has a couple raid-1 arrays on it right now. But we need the raid-5 to be activated because there is a volgroup that uses the raid-5 device as it's PV.

Regards,
Gerry

#4 lore raw
Quoted 8 lines · Gerry Reno
Quoted 7 lines · Eric Brunson
Quoted 4 lines · Eric Brunson
Quoted 1 line · Gerry Reno

We built a replacement server (x86_64) for an older server (x86). Now we want to move a RAID-5 array intact from the older machine over to the new machine. We know the UUID of the array and of all the PV and VG on the array. So what commands should we perform after plugging in all the array drives to the new server to bring up the array and lvm on the new machine?

"vgscan" and "vgchange -a VGNAME" I believe.

Quoted 7 lines
Quoted 6 lines

Sorry, doing three things at once: vgchange -a y VGNAME

Quoted 3 lines

Make sure your VG name doesn't conflict with any already in the machine.

Will vgchange activate the raid array?

Is it an md (software) RAID or a hardware RAID device?

If the former, then I'm not sure. I'll have to defer to someone with more md experience. If the latter, then it depends of if you have the correct drivers and hardware detection.

Quoted 11 lines

The new server just has a couple raid-1 arrays on it right now. But we need the raid-5 to be activated because there is a volgroup that uses the raid-5 device as it's PV.

Regards,
Gerry

_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

author
#5 lore raw
Quoted 15 lines · Eric Brunson
Quoted 14 lines · Gerry Reno
Quoted 13 lines · Eric Brunson
Quoted 4 lines · Eric Brunson
Quoted 1 line · Gerry Reno

We built a replacement server (x86_64) for an older server (x86). Now we want to move a RAID-5 array intact from the older machine over to the new machine. We know the UUID of the array and of all the PV and VG on the array. So what commands should we perform after plugging in all the array drives to the new server to bring up the array and lvm on the new machine?

"vgscan" and "vgchange -a VGNAME" I believe.

Sorry, doing three things at once: vgchange -a y VGNAME

Quoted 3 lines

Make sure your VG name doesn't conflict with any already in the machine.

Quoted 12 lines
Quoted 1 line

Will vgchange activate the raid array?

Is it an md (software) RAID or a hardware RAID device?

If the former, then I'm not sure. I'll have to defer to someone with more md experience. If the latter, then it depends of if you have the correct drivers and hardware detection.

Quoted 3 lines

The new server just has a couple raid-1 arrays on it right now. But we need the raid-5 to be activated because there is a volgroup that uses the raid-5 device as it's PV.

It's an 'md' software raid device. I think we can probably just try to assemble the array using the UUID. Maybe something like:
mdadm -vv -A /dev/md4 --uuid=UUID

Regards,
Gerry

#6 lore raw
Quoted 3 lines · Gerry Reno

It's an 'md' software raid device. I think we can probably just try to assemble the array using the UUID. Maybe something like:
mdadm -vv -A /dev/md4 --uuid=UUID

the above depende on the device line in your mdadm.conf,
if it is something like 'DEVICE partitions' or 'DEVICE /dev/*' it should work.
you still would like to have it in mdadm.conf for automatic activation at boot.
i would run
mdadm -Esc partitions | grep UUID

maybe check the line you added to see if the minor is what you want and add it to /etc/mdadm.conf

L.

Signature · 6 lines
Luca Berra -- [email protected]
        Communication Media & Services S.r.l.
 /"\
 \ /     ASCII RIBBON CAMPAIGN
  X        AGAINST HTML MAIL
 / \