Hauppauge 950Q Analog (Composite Input) Problem
Hello,
Actually, I am trying to use the analog composite input (not cable television) working. Is this part of analog support? Or is that for analog cable only?
When I hook a video source up to the composite RCA jack and "mplayer /dev/video" it presents the following:
MPlayer dev-SVN-r26753-4.1.2 (C) 2000-2008 MPlayer Team
CPU: Intel(R) Pentium(R) M processor 1.20GHz (Family: 6, Model: 13, Stepping: 8)
CPUflags: MMX: 1 MMX2: 1 3DNow: 0 3DNow2: 0 SSE: 1 SSE2: 1 Compiled for x86 CPU with extensions: MMX MMX2 SSE SSE2
Playing /dev/video.
It just sits there. Typing "cat /dev/video" does not produce any output.
Linux aqui 2.6.29.2. I am running hvr950q-analog-1bbabf78f9ef (downloaded a couple days ago).
From log output everything seems good:
May 4 18:52:19 aqui usb 1-1: new high speed USB device using ehci_hcd and address 5 May 4 18:52:19 aqui usb 1-1: configuration #1 chosen from 1 choice May 4 18:52:20 aqui Linux video capture interface: v2.00 May 4 18:52:20 aqui au0828 driver loaded May 4 18:52:20 aqui au0828: i2c bus registered May 4 18:52:20 aqui tveeprom 1-0050: Hauppauge model 72001, rev B3F0, serial# 6134581 May 4 18:52:20 aqui tveeprom 1-0050: MAC address is 00-0D-FE-5D-9B-35 May 4 18:52:20 aqui tveeprom 1-0050: tuner model is Xceive XC5000 (idx 150, type 76) May 4 18:52:20 aqui tveeprom 1-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88) May 4 18:52:20 aqui tveeprom 1-0050: audio processor is AU8522 (idx 44) May 4 18:52:20 aqui tveeprom 1-0050: decoder processor is AU8522 (idx 42) May 4 18:52:20 aqui tveeprom 1-0050: has no radio, has IR receiver, has no IR transmitter May 4 18:52:20 aqui hauppauge_eeprom: hauppauge eeprom: model=72001 May 4 18:52:20 aqui au8522 1-0047: creating new instance May 4 18:52:20 aqui au8522_decoder creating new instance... May 4 18:52:20 aqui tuner 1-0061: chip found @ 0xc2 (au0828) May 4 18:52:20 aqui xc5000 1-0061: creating new instance May 4 18:52:20 aqui xc5000: Successfully identified at address 0x61 May 4 18:52:20 aqui xc5000: Firmware has not been loaded previously May 4 18:52:20 aqui xc5000: waiting for firmware upload (dvb-fe-xc5000-1.1.fw)... May 4 18:52:20 aqui i2c-adapter i2c-1: firmware: requesting dvb-fe-xc5000-1.1.fw May 4 18:52:20 aqui xc5000: firmware read 12332 bytes. May 4 18:52:20 aqui xc5000: firmware upload May 4 18:52:31 aqui au8522 1-0047: attaching existing instance May 4 18:52:31 aqui xc5000 1-0061: attaching existing instance May 4 18:52:31 aqui xc5000: Successfully identified at address 0x61 May 4 18:52:31 aqui xc5000: Firmware has been loaded previously May 4 18:52:31 aqui DVB: registering new adapter (au0828) May 4 18:52:31 aqui DVB: registering adapter 0 frontend 0 (Auvitek AU8522 QAM/8VSB Frontend)... May 4 18:52:31 aqui Registered device AU0828 [Hauppauge HVR950Q] May 4 18:52:31 aqui usbcore: registered new interface driver au0828
Thanks,
John
Quoted 64 lines · John R.
Hello,
Actually, I am trying to use the analog composite input (not cable television) working. Is this part of analog support? Or is that for analog cable only?
When I hook a video source up to the composite RCA jack and "mplayer
/dev/video" it presents the following:MPlayer dev-SVN-r26753-4.1.2 (C) 2000-2008 MPlayer Team
CPU: Intel(R) Pentium(R) M processor 1.20GHz (Family: 6, Model: 13,
Stepping: 8)
CPUflags: MMX: 1 MMX2: 1 3DNow: 0 3DNow2: 0 SSE: 1 SSE2: 1 Compiled for x86 CPU with extensions: MMX MMX2 SSE SSE2Playing
/dev/video.It just sits there. Typing "cat
/dev/video" does not produce any output.Linux aqui 2.6.29.2. I am running hvr950q-analog-1bbabf78f9ef (downloaded a couple days ago).
From log output everything seems good:
May 4 18:52:19 aqui usb 1-1: new high speed USB device using
ehci_hcdand address 5
May 4 18:52:19 aqui usb 1-1: configuration #1 chosen from 1 choice May 4 18:52:20 aqui Linux video capture interface: v2.00
May 4 18:52:20 aqui au0828 driver loaded
May 4 18:52:20 aqui au0828: i2c bus registered
May 4 18:52:20 aqui tveeprom 1-0050: Hauppauge model 72001, rev B3F0, serial# 6134581
May 4 18:52:20 aqui tveeprom 1-0050: MAC address is 00-0D-FE-5D-9B-35 May 4 18:52:20 aqui tveeprom 1-0050: tuner model is Xceive XC5000 (idx 150, type 76)
May 4 18:52:20 aqui tveeprom 1-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom0x88)
May 4 18:52:20 aqui tveeprom 1-0050: audio processor is AU8522 (idx 44) May 4 18:52:20 aqui tveeprom 1-0050: decoder processor is AU8522 (idx 42) May 4 18:52:20 aqui tveeprom 1-0050: has no radio, has IR receiver, has no IR transmitter
May 4 18:52:20 aquihauppauge_eeprom: hauppauge eeprom: model=72001 May 4 18:52:20 aqui au8522 1-0047: creating new instance
May 4 18:52:20 aquiau8522_decodercreating new instance...
May 4 18:52:20 aqui tuner 1-0061: chip found @0xc2(au0828) May 4 18:52:20 aqui xc5000 1-0061: creating new instance
May 4 18:52:20 aqui xc5000: Successfully identified at address0x61May 4 18:52:20 aqui xc5000: Firmware has not been loaded previously May 4 18:52:20 aqui xc5000: waiting for firmware upload (dvb-fe-xc5000-1.1.fw)...
May 4 18:52:20 aqui i2c-adapter i2c-1: firmware: requesting dvb-fe-xc5000-1.1.fw
May 4 18:52:20 aqui xc5000: firmware read 12332 bytes.
May 4 18:52:20 aqui xc5000: firmware upload
May 4 18:52:31 aqui au8522 1-0047: attaching existing instance May 4 18:52:31 aqui xc5000 1-0061: attaching existing instance May 4 18:52:31 aqui xc5000: Successfully identified at address0x61May 4 18:52:31 aqui xc5000: Firmware has been loaded previously May 4 18:52:31 aqui DVB: registering new adapter (au0828)
May 4 18:52:31 aqui DVB: registering adapter 0 frontend 0 (Auvitek AU8522 QAM/8VSB Frontend)...
May 4 18:52:31 aqui Registered device AU0828 [Hauppauge HVR950Q] May 4 18:52:31 aqui usbcore: registered new interface driver au0828
Quoted 8 lines
Thanks,
John
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hello John,
That's not really how v4l2 capture works, in particular with devices that do not provide an mpeg stream (you cannot just run "mplayer /dev/video0"). You're not actually doing any sort of input selection, so how are you expecting the driver to know to capture on the composite input?
I would suggest you give the man page for mplayer a read, in particular the options related to driver=v4l2. If you still have questions, email the ML.
Cheers,
Devin
Signature · 3 lines
Devin J. Heitmueller http://www.devinheitmueller.com AIM: devinheitmueller
Quoted 3 lines · kenny wang
Hi, John
I am using exactly the same device, and several weeks ago Devin helped me make it work perfectly. I downloaded and compiled the newest codes from v4l mecurial, and simply use tvtime to play the video. But you need to use some other command to play sound:
Thanks. Devin's response got me through the basic stuff I was missing.
Yours should help quite a bit in getting sound to work. For anyone
that is working with composite input, here is a sample invocation for video only:
mplayer tv:// -tv driver=v4l2:input=1:norm=ntsc:width=640:height=480:device=/dev/video0 -vo xv
John