Nova-T 500 does not survive reboot
Subsystems (2)
Quoted 14 lines
Quoted 14 lines
Quoted 4 lines
Hi,
Any news on this? I'd like to try the URB patch someone mentioned,
but I
can't find the link.http://www.mail-archive.com/[email protected]/msg04643.html
I am running a current dvb tree with this patch.
so far so good.
I did not find the time to check if I regained proper reboots, though. I know, sad excuse...
Quoted 7 lines
Quoted 3 lines
nico
I'll give it a try. Thanks for the tip!
Cheers,
Eduard
Hi nico, Eduard,
can you confirm that the patch solves your Nova-T 500 boot problem? In this case I would resend the buffer count part as separate patch to Patrick.
S:oren
Quoted 22 lines · Soeren Moch
Quoted 14 lines
Quoted 14 lines
Quoted 4 lines
Hi,
Any news on this? I'd like to try the URB patch someone mentioned,
but I
can't find the link.http://www.mail-archive.com/[email protected]/msg04643.html
I am running a current dvb tree with this patch.
so far so good.
I did not find the time to check if I regained proper reboots, though. I know, sad excuse...
Quoted 7 lines
Quoted 3 lines
nico
I'll give it a try. Thanks for the tip!
Cheers,
Eduard
Quoted 5 lines
Hi nico, Eduard,
can you confirm that the patch solves your Nova-T 500 boot problem? In this case I would resend the buffer count part as separate patch to Patrick.
It doesn;t appear to fix it.
I'll retry this evening, after the F1 Grand Prix.
Nico
Re: DVB USB stream parameters
In reply to Soeren MochQuoted 1 line
I don't know exactly why (the USB/HW background for that is not present in my brain), but at some point having less than 39480B for one (high-level) URB for the dib0700 resulted in never having any URB returning from the USB stack. I chose 4 of them because .. I don't remember. It seems even 1 is working.
I vote for a single high-level URB. Besides the memory savings this is the only way I could get my nova-td stick working. (see this thread: http://www.mail-archive.com/[email protected]/msg06376.html ) The patch runs flawlessly on my vdr system for months now.
Quoted 1 line
I remember someone telling me that this is due to something in the firmware. I need to wait for some people to be back from whereever they are to know exactly what's going on (that's why I haven't responded yet).
I hope you can sort out the dib0700_streaming_ctrl problems...
Soeren
dib0700 i2c problem / mt2266 patch
Patrick,
when you are discussing dib0700 issues with dibcom, there is an additional one for the list:
When using dib0700 in dual mode (on my nova-td stick), from time to time a tuner hangs up. I never observed this behavior in single mode. It seems to me that there is no proper locking within the dib0700 firmware when accessing both tuner i2c buses "simultaneously".
Since I only need UHF channels, I use the attached patch to decrease the number of i2c transactions and tuner registers, which are involved in the channel switch. This solved the tuning problems.
Besides the i2c problem, maybe it might be a good idea to integrate this patch into the mt2266 driver anyway, because it considerably speeds up the channel switch.
Regards,
S:oren
media/common/tuners/mt2266.c renamed from media/common/tuners/mt2266.c.orig +19 -16
@@ -137,7 +137,6 @@ static int mt2266_set_params(struct dvb_ freq = params->frequency /1000 ;// Hz -> kHz if (freq <470000 && freq >230000 )return -EINVAL ;/* Gap between VHF and UHF bands */ - priv->bandwidth = (fe->ops.info.type ==FE_OFDM ) ? params->u.ofdm.bandwidth :0 ; priv->frequency = freq *1000 ; tune =2 * freq * (8192 /16 ) / (FREF /16 );
@@ -145,21 +144,24 @@ static int mt2266_set_params(struct dvb_if (band ==MT2266_VHF ) tune *=2 ; -switch (params->u.ofdm.bandwidth) { -case BANDWIDTH_6_MHZ : -mt2266_writeregs (priv, mt2266_init_6mhz, -sizeof (mt2266_init_6mhz)); -break ; -case BANDWIDTH_7_MHZ : -mt2266_writeregs (priv, mt2266_init_7mhz, -sizeof (mt2266_init_7mhz)); -break ; -case BANDWIDTH_8_MHZ : -default : -mt2266_writeregs (priv, mt2266_init_8mhz, -sizeof (mt2266_init_8mhz)); -break ; - } +if (priv->bandwidth != params->u.ofdm.bandwidth) { + priv->bandwidth = (fe->ops.info.type ==FE_OFDM ) ? params->u.ofdm.bandwidth :0 ; +switch (params->u.ofdm.bandwidth) { +case BANDWIDTH_6_MHZ : +mt2266_writeregs (priv, mt2266_init_6mhz, +sizeof (mt2266_init_6mhz)); +break ; +case BANDWIDTH_7_MHZ : +mt2266_writeregs (priv, mt2266_init_7mhz, +sizeof (mt2266_init_7mhz)); +break ; +case BANDWIDTH_8_MHZ : +default : +mt2266_writeregs (priv, mt2266_init_8mhz, +sizeof (mt2266_init_8mhz)); +break ; + } + }if (band ==MT2266_VHF && priv->band ==MT2266_UHF ) {dprintk ("Switch from UHF to VHF" );
@@ -327,6 +329,7 @@ struct dvb_frontend * mt2266_attach(stru priv->cfg = cfg; priv->i2c = i2c; + priv->bandwidth=BANDWIDTH_8_MHZ ; priv->band =MT2266_UHF ;if (mt2266_readreg (priv,0 , &id)) {