usb fails to suspend [was: mmotm 2009-06-05-16-19]
Hi,
there is a suspend regression somewhere between mmotm 2009-05-17-12-15 and 2009-06-05-16-19:hcd_pci_suspend_noirq(): pci_prepare_to_sleep+0x0/0x80 returns -19 pci_pm_suspend_noirq(): hcd_pci_suspend_noirq+0x0/0xb0 returns -19 pm_noirq_op(): pci_pm_suspend_noirq+0x0/0x180 returns -19
PM: Device 0000:00:1d.2 failed to suspend late: error -19
$ lspci -xxvvs 0000:00:1d.2
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d000 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00Any ideas?
Quoted 28 lines · Jiri Slaby
Hi,
there is a suspend regression somewhere between mmotm 2009-05-17-12-15 and 2009-06-05-16-19:
hcd_pci_suspend_noirq():pci_prepare_to_sleep+0x0/0x80returns -19pci_pm_suspend_noirq():hcd_pci_suspend_noirq+0x0/0xb0returns -19pm_noirq_op():pci_pm_suspend_noirq+0x0/0x180returns -19
PM: Device 0000:00:1d.2 failed to suspend late: error -19$ lspci -xxvvs 0000:00:1d.2 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at d000 [size=32] Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd 00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
Quoted 1 line
Any ideas?
Not really. Is it -mm-only or is the mainline affected too?
Hi Jiri,
Quoted 7 lines
there is a suspend regression somewhere between mmotm 2009-05-17-12-15 and 2009-06-05-16-19:
hcd_pci_suspend_noirq():pci_prepare_to_sleep+0x0/0x80returns -19pci_pm_suspend_noirq():hcd_pci_suspend_noirq+0x0/0xb0returns -19pm_noirq_op():pci_pm_suspend_noirq+0x0/0x180returns -19
PM: Device 0000:00:1d.2 failed to suspend late: error -19
Quoted 5 lines
$ lspci -xxvvs 0000:00:1d.2
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3what is the likelihood that you have an Intel WiMAX card in this system? There is a suspend issue when i2400m_usb is loaded. Took me a while to figure that one out. It suspends/resumes fine for the first time after reboot, but on resume it deadlocks the whole USB subsystem.
Regards
Marcel
Quoted 1 line · Marcel Holtmann
Hi Jiri,
Hi.
Quoted 7 lines
Quoted 5 lines
$ lspci -xxvvs 0000:00:1d.2 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3what is the likelihood that you have an Intel WiMAX card in this system?
None :) -- I have no such card in the system.
Quoted 3 lines
There is a suspend issue when
i2400m_usbis loaded. Took me a while to figure that one out. It suspends/resumes fine for the first time after reboot, but on resume it deadlocks the whole USB subsystem.
This was the first time I tried to suspend.
Hi Jiri,
Quoted 8 lines
Quoted 7 lines
Quoted 5 lines
$ lspci -xxvvs 0000:00:1d.2 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3what is the likelihood that you have an Intel WiMAX card in this system?
Quoted 7 lines
None :) -- I have no such card in the system.
Quoted 3 lines
There is a suspend issue when
i2400m_usbis loaded. Took me a while to figure that one out. It suspends/resumes fine for the first time after reboot, but on resume it deadlocks the whole USB subsystem.This was the first time I tried to suspend.
then it is not that issue and I have no idea what happens.
Regards
Marcel
Quoted 29 lines · Rafael J. Wysocki
Quoted 28 lines · Jiri Slaby
Hi,
there is a suspend regression somewhere between mmotm 2009-05-17-12-15 and 2009-06-05-16-19:
hcd_pci_suspend_noirq():pci_prepare_to_sleep+0x0/0x80returns -19pci_pm_suspend_noirq():hcd_pci_suspend_noirq+0x0/0xb0returns -19pm_noirq_op():pci_pm_suspend_noirq+0x0/0x180returns -19
PM: Device 0000:00:1d.2 failed to suspend late: error -19$ lspci -xxvvs 0000:00:1d.2 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at d000 [size=32] Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd 00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
Quoted 3 lines
Quoted 1 line
Any ideas?
Not really. Is it -mm-only or is the mainline affected too?
Yup, only an -mm thing. I reverted these two:
pci-pm-read-device-power-state-from-register-after-updating-it.patch pci-pm-read-device-power-state-from-register-after-updating-it-update.patch and it works now :).
Quoted 30 lines · Jiri Slaby
Quoted 29 lines · Rafael J. Wysocki
Quoted 28 lines · Jiri Slaby
Hi,
there is a suspend regression somewhere between mmotm 2009-05-17-12-15 and 2009-06-05-16-19:
hcd_pci_suspend_noirq():pci_prepare_to_sleep+0x0/0x80returns -19pci_pm_suspend_noirq():hcd_pci_suspend_noirq+0x0/0xb0returns -19pm_noirq_op():pci_pm_suspend_noirq+0x0/0x180returns -19
PM: Device 0000:00:1d.2 failed to suspend late: error -19$ lspci -xxvvs 0000:00:1d.2 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at d000 [size=32] Capabilities: [50] Vendor Specific Information <?> Kernel driver in use: uhci_hcd 00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
Quoted 8 lines
Quoted 3 lines
Quoted 1 line
Any ideas?
Not really. Is it -mm-only or is the mainline affected too?
Yup, only an -mm thing. I reverted these two:
pci-pm-read-device-power-state-from-register-after-updating-it.patch pci-pm-read-device-power-state-from-register-after-updating-it-update.patch and it works now :).
OK, thanks.
Andrew, can you drop these two patches from -mm please?
Best,
Rafael