Skip to contentSkip to conversation

Problem booting Linux from Flash

U-Boot Rahanesh 2 participants 3 messages Jul 20, 2009 – Jul 22, 2009

lore
Share & tools
lore

Rahanesh

author
#0 lore raw

Hi all,

I am trying to boot Linux from flash on MIPS Board. When uBoot tries to boot Linux it fails saying "Verifying Checksum Failed.... bad data crc".
The bootcmd is fsload 0x80800000 /boot/uImage; bootm 0x80800000.

But When i do a tftp of the same image(uImage) to same address(0x80800000) it works fine.
What might be the problem when it is loading uImage from flash?

Log is as shown below:

Bootrom Version [RTEMS]: Rel_30
Chip: Atlanta A80
Board: REF MTA

U-Boot 1.1.2 (Jul 17 2009 - 10:32:57)

Board: MIPS CPU Speed 200 MHz
DRAM:  32 MB

sflash.c:266:DF_F_DataflashProbe: Entered sflash.c:269:DF_F_DataflashProbe: flash type is 0x1 sflash.c:270:DF_F_DataflashProbe: num pages 32768 DataFlash:Nb pages: 32768
Page Size: 256
Size= 8388608 bytes

Logical address: 0xAD000000
Nb Erase Blocks:    128
Erase Block Size:  65536
Area 0: AD000000 to AD003FFF
Area 1: AD004000 to AD03FFFF
Area 2: AD040000 to AD30BFFF
Area 3: AD30C000 to AD7FFFFF
crc matched
In:    serial
Out:   serial
Err:   serial
Net:   Eth.

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot: 0
### JFFS2 loading '/boot/uImage' to 0x80800000 Scanning JFFS2 FS: . done.
### JFFS2 load complete: 1853548 bytes loaded to 0x80800000 ## Booting image at 80800000 ...

   Image Name:   Linux Kernel Image with ramdisk.
   Created:      2009-07-17  11:01:27 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    1853484 Bytes =  1.8 MB

Load Address: 80100000
Entry Point: 80423000
Verifying Checksum ... Bad Data CRC
uboot>#

Please Help

Thanks
Rahanesh

#1 lore raw

Dear Rahanesh,

Quoted 4 lines · In message <[email protected]> you wrote:

I am trying to boot Linux from flash on MIPS Board. When uBoot tries to boot Linux it fails saying "Verifying Checksum Failed.... bad data crc".

CRC is one type of checksum.

Quoted 1 line

What might be the problem when it is loading uImage from flash?

Obviously the loaded data are corrupt. Based on the information you gave us it is impossible to tell if the data are already corrupt in your JFFS2 file system, of if they get corrupted when loading the file, or when booting it.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Humans do claim a great deal for that particular emotion (love).
	-- Spock, "The Lights of Zetar", stardate 5725.6
author
#2 lore raw

Hi Wolfgang Denk,

Thanks a lot for your reply.

Actually problem started when i added few utilities in flash. I ll explain the scenario.

I had a working jffs image with bin , boot, scripts as directories in it. uImage(Linux kernel image ) was contained in boot folder.

For my application i had to add few new networking utilitiess like iptables, brctl, racoon etc..
Hence i added these utilities in bin directory and created a new jffs image.

This jffs image was flashed to board. This image gave the CRC error when uboot tried to boot.

Now instead of adding the utilities to bin i added all the utilities to a new created Utility Directory. This time It worked fine. The jffs image was flashed and uboot successfully loaded uImage and booting was perfect.

What might be the reason behind this? can u please throw some light on this?

Thanks
Rahanesh

Quoted 25 lines · Wolfgang Denk

Dear Rahanesh,

Quoted 4 lines · In message <[email protected]> you wrote:

I am trying to boot Linux from flash on MIPS Board. When uBoot tries to boot Linux it fails saying "Verifying Checksum Failed.... bad data crc".

CRC is one type of checksum.

Quoted 2 lines

What might be the problem when it is loading uImage from flash?

Obviously the loaded data are corrupt. Based on the information you gave us it is impossible to tell if the data are already corrupt in your JFFS2 file system, of if they get corrupted when loading the file, or when booting it.

Best regards,

Wolfgang Denk