Skip to contentSkip to conversation

Disk access just before shutdown power off.

DISCUSSION James Courtier-Dutton 5 participants 5 messages Jul 20, 2009 – Jul 21, 2009

lore
Share & tools
lore
#0 lore raw

Hi,

When I shutdown my Linux laptop, it does an orderly shutdown with quite a lot of HD activity during shutdown which eventually stops when the screen goes blank. Then there is some delay (5-10 seconds) and then a quick flurry of HD access just before it powers itself off. Why is this last bit of HD access needed?
Surely, if the system is shut down enough to not use the screen any more, why does it need the HD?
I am asking, because it would be nice to disable this need of the HD just before it powers itself off. This would allow me to lift up the laptop just a bit earlier and place it in my backpack when the screen blanks without having to worry about HD failure due to shock. I think it would be nicer if the HD would shut itself down just before the screen goes blank.

Kind Regards

James

#1 lore raw
Quoted 15 lines · James Courtier-Dutton

Hi,

When I shutdown my Linux laptop, it does an orderly shutdown with quite a lot of HD activity during shutdown which eventually stops when the screen goes blank. Then there is some delay (5-10 seconds) and then a quick flurry of HD access just before it powers itself off. Why is this last bit of HD access needed?
Surely, if the system is shut down enough to not use the screen any more, why does it need the HD?
I am asking, because it would be nice to disable this need of the HD just before it powers itself off. This would allow me to lift up the laptop just a bit earlier and place it in my backpack when the screen blanks without having to worry about HD failure due to shock. I think it would be nicer if the HD would shut itself down just before the screen goes blank.

It's not clear exactly what point in the shutdown process the screen going blank corresponds to. Do you have the kernel output going to the console during the shutdown process? If not, enabling that might be useful to tell what's going on.

The last thing the kernel does with the disk before power-off is flush the cache and tell it to go into standby mode. It seems like some disks are dumb enough to spin up as a result even if there's nothing to flush and it was already spun down. Also, in some cases the BIOS decides to issue its own such commands after the OS tells it to power down, which can have similar results. I believe there's a blacklist of system models that are set to skip the kernel standby issuing to avoid the double spin-down.

#2 lore raw
In reply to James Courtier-Dutton
Quoted 4 lines · James Courtier-Dutton

When I shutdown my Linux laptop, it does an orderly shutdown with quite a lot of HD activity during shutdown which eventually stops when the screen goes blank. Then there is some delay (5-10 seconds) and then a quick flurry of HD access just before it powers itself off.

That would be the journal being synced back to disk as an fsync is done prior to unmounting/remounting-ro. You can't do anything about this because it needs to be the last thing that is done.

Jon.

#3 lore raw
In reply to James Courtier-Dutton
Quoted 4 lines · James Courtier-Dutton

When I shutdown my Linux laptop, it does an orderly shutdown with quite a lot of HD activity during shutdown which eventually stops when the screen goes blank. Then there is some delay (5-10 seconds) and then a quick flurry of HD access just before it powers itself off.

Either your BIOS does something very weird with your disk when OS commands it to power off (unlikely),

or your system is set up in a way where there is no visible output when X is killed, but the system (Linux) is still running (shutting itself down).

Some distributions get fancy ideas about "not scaring users with this text output scrolling up at boot & shutdown".

This has nice side effect of users not noticing any potentially useful messages at boot or shutdown. :(

--
vda

#4 lore raw
In reply to James Courtier-Dutton

2009/7/20 James Courtier-Dutton <[email protected]>:

Quoted 16 lines

Hi,

When I shutdown my Linux laptop, it does an orderly shutdown with quite a lot of HD activity during shutdown which eventually stops when the screen goes blank. Then there is some delay (5-10 seconds) and then a quick flurry of HD access just before it powers itself off. Why is this last bit of HD access needed?
Surely, if the system is shut down enough to not use the screen any more, why does it need the HD?
I am asking, because it would be nice to disable this need of the HD just before it powers itself off. This would allow me to lift up the laptop just a bit earlier and place it in my backpack when the screen blanks without having to worry about HD failure due to shock. I think it would be nicer if the HD would shut itself down just before the screen goes blank.

It's HP/Compaq laptop?

Regards

Signature · 2 lines
Maciej Rutecki
http://www.maciek.unixy.pl