Skip to contentSkip to conversation

No UDMA with BLK_DEV_IT821X with 2.6.30.2

DISCUSSION Dwayne Rightler 3 participants 4 messages Jul 20, 2009 – Jul 21, 2009

lore
Share & tools
lore
#0 lore raw

Hello,

I have a ITE8212 PCI card and it does not seem to allow UDMA on the drives attached. The drives run at ATA100 under other controllers.

Dmesg:

[    3.029612] it821x 0000:01:07.0: IDE controller (0x1283:0x8212 rev 0x13)
[    3.029835] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[    3.029840] pci 0000:01:07.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
[    3.029847] it821x 0000:01:07.0: controller in smart mode
[    3.029848] it821x 0000:01:07.0: 100% native mode on irq 19
[    3.029852]     ide1: BM-DMA at 0xcb00-0xcb07
[    3.029857]     ide2: BM-DMA at 0xcb08-0xcb0f
[    3.029859] Probing IDE interface ide1...
[    3.316151] hdc: ST3400633A, ATA DISK drive
[    3.652003] hdd: ST3400633A, ATA DISK drive
[    3.652018] hdc: Performing identify fixups.
[    3.652019] hdd: Performing identify fixups.
[    3.652022] hdc: MWDMA2 mode selected
[    3.652026] hdd: MWDMA2 mode selected
[    3.652028] Probing IDE interface ide2...
[    3.940151] hde: ST3400633A, ATA DISK drive
[    4.276003] hdf: ST3400633A, ATA DISK drive
[    4.276015] hde: Performing identify fixups.
[    4.276016] hdf: Performing identify fixups.
[    4.276019] hde: MWDMA2 mode selected
[    4.276023] hdf: MWDMA2 mode selected
[    4.276037] ide1 at 0xcf00-0xcf07,0xce02 on irq 19
[    4.276052] ide2 at 0xcd00-0xcd07,0xcc02 on irq 19
[    4.276187] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
[    4.276195] ide-gd driver 1.18
[    4.276210] hdc: max request size: 128KiB
[    4.276212] hdc: 781422768 sectors (400088 MB) w/16384KiB Cache, CHS=48641/255/63
[    4.276233]  hdc:<3>hdc: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
[    4.280086] hdc: task_no_data_intr: error=0x04 { DriveStatusError }
[    4.280323] hdc: possibly failed opcode: 0x10
[    5.445905]  hdc1
[    5.445972] hdd: max request size: 128KiB
[    5.445974] hdd: 781422768 sectors (400088 MB) w/16384KiB Cache, CHS=48641/255/63
[    5.445989]  hdd:<3>hdd: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
[    5.448080] hdd: task_no_data_intr: error=0x04 { DriveStatusError }
[    5.448314] hdd: possibly failed opcode: 0x10
[    6.609738]  hdd1
[    6.609795] hde: max request size: 128KiB
[    6.609797] hde: 781422768 sectors (400088 MB) w/16384KiB Cache, CHS=48641/255/63
[    6.609813]  hde:<3>hde: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
[    6.612080] hde: task_no_data_intr: error=0x04 { DriveStatusError }
[    6.612315] hde: possibly failed opcode: 0x10
[    7.772545]  hde1
[    7.772600] hdf: max request size: 128KiB
[    7.772602] hdf: 781422768 sectors (400088 MB) w/16384KiB Cache, CHS=48641/255/63
[    7.772617]  hdf:<3>hdf: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
[    7.776081] hdf: task_no_data_intr: error=0x04 { DriveStatusError }
[    7.776316] hdf: possibly failed opcode: 0x10
[    8.937987]  hdf1

hdparm:

/dev/hdd:

Model=ST3400633A, FwRev=3.AAH, SerialNo=3NF1QK7K
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4 BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=781422768 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: *mdma0 mdma1 mdma2
AdvancedPM=no
Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7

* signifies the current active mode

#1 lore raw
Quoted 4 lines · On Mon, 20 Jul 2009 18:03:22 -0500 Dwayne Rightler…

Hello,

I have a ITE8212 PCI card and it does not seem to allow UDMA on the drives attached. The drives run at ATA100 under other controllers.

The old IDE driver support for IT821x has been somewhat broken for some time. The drivers/ata (libata) driver should handle it fully. In smart mode it's "IDE-ish" and the old IDE code really isn't flexible enough to cope. With the "ATAPI BIOS" its a fairly normal controller so both drivers ought to work.

#2 lore raw

With the libata driver and "ATAPI BIOS" I get this sort of garbage (note I don't get these drive errors on other controllers):

[  604.314837] ata8.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[  604.314895] ata8.01: BMDMA stat 0x4
[  604.314951] ata8.01: cmd c8/00:00:e0:20:e4/00:00:00:00:00/f1 tag 0 dma 131072 in
[  604.314952]          res 00/00:00:80:00:80/00:00:00:00:00/80 Emask 0x2 (HSM violation)
[  604.315097] ata8: soft resetting link
[  605.462588] ata8.00: configured for UDMA/100
[  605.508491] ata8.01: configured for UDMA/100
[  605.508501] ata8: EH complete
[  979.174939] ata8.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[  979.174949] ata8.01: BMDMA stat 0x4
[  979.174958] ata8.01: cmd c8/00:00:e0:4e:89/00:00:00:00:00/f4 tag 0 dma 131072 in
[  979.174959]          res 00/00:00:80:00:80/00:00:00:00:00/80 Emask 0x2 (HSM violation)
[  979.175008] ata8: soft resetting link
[  979.944287] ata8.01: NODEV after polling detection
[  979.944290] ata8.01: revalidation failed (errno=-2)
[  984.944026] ata8: soft resetting link
[  985.100384] ata8.01: NODEV after polling detection
[  985.100388] ata8.01: revalidation failed (errno=-2)
[  990.100032] ata8: soft resetting link
[  990.256322] ata8.01: NODEV after polling detection
[  990.256325] ata8.01: revalidation failed (errno=-2)
[  990.256334] ata8.01: disabled
[  990.256338] ata8.00: failed to IDENTIFY (I/O error, err_mask=0x40)
[  990.256340] ata8.00: revalidation failed (errno=-5)
[  995.256024] ata8: soft resetting link
[  995.539133] ata8.00: configured for UDMA/100
[  995.539158] ata8: EH complete
[  995.539185] sd 7:0:1:0: [sdg] Unhandled error code
[  995.539187] sd 7:0:1:0: [sdg] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  995.539192] end_request: I/O error, dev sdg, sector 76107488
[  995.539206] Buffer I/O error on device sdg, logical block 9513436
[  995.539215] Buffer I/O error on device sdg, logical block 9513437
[  995.539222] Buffer I/O error on device sdg, logical block 9513438
[  995.539229] Buffer I/O error on device sdg, logical block 9513439
[  995.539244] Buffer I/O error on device sdg, logical block 9513440
[  995.539260] Buffer I/O error on device sdg, logical block 9513441
[  995.539276] Buffer I/O error on device sdg, logical block 9513442
[  995.539292] Buffer I/O error on device sdg, logical block 9513443
[  995.539308] Buffer I/O error on device sdg, logical block 9513444
[  995.539323] Buffer I/O error on device sdg, logical block 9513445
[  995.539359] sd 7:0:1:0: [sdg] Unhandled error code
[  995.539361] sd 7:0:1:0: [sdg] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  995.539364] end_request: I/O error, dev sdg, sector 76107744
[  995.539411] sd 7:0:1:0: [sdg] Unhandled error code
[  995.539413] sd 7:0:1:0: [sdg] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  995.539415] end_request: I/O error, dev sdg, sector 76107488

After this happens hdparm fails:

root@darkomen-desktop:~# hdparm -i /dev/sdg

/dev/sdg:
HDIO_GET_IDENTITY failed: No message of desired type

As well as smartctl:

root@darkomen-desktop:~# smartctl -H /dev/sdg
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

Short INQUIRY response, skip product id
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.

Quoted 12 lines · Alan Cox
Quoted 3 lines · On Mon, 20 Jul 2009 18:03:22 -0500 Dwayne Rightler…

Hello,

I have a ITE8212 PCI card and it does not seem to allow UDMA on the drives attached. The drives run at ATA100 under other controllers.

The old IDE driver support for IT821x has been somewhat broken for some time. The drivers/ata (libata) driver should handle it fully. In smart mode it's "IDE-ish" and the old IDE code really isn't flexible enough to cope. With the "ATAPI BIOS" its a fairly normal controller so both drivers ought to work.

#3 lore raw
In reply to Dwayne Rightler
Quoted 5 lines · On Tuesday 21 July 2009 01:03:22 Dwayne Rightler wrote:

Hello,

I have a ITE8212 PCI card and it does not seem to allow UDMA on the drives attached. The drives run at ATA100 under other controllers.

Quoted 7 lines

Dmesg:

[    3.029612] it821x 0000:01:07.0: IDE controller (0x1283:0x8212 rev 0x13)
[    3.029835] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[    3.029840] pci 0000:01:07.0: PCI INT A -> Link[APC4] -> GSI 19 
(level, low) -> IRQ 19
[    3.029847] it821x 0000:01:07.0: controller in smart mode

The controller is running in the "smart mode" in which it takes care of setting the transfer speed (the driver reports standard MWDMA2 mode to higher-layers for compatibility reasons).