Skip to contentSkip to conversation

clock freezes??

DISCUSSION Victor Mataré 2 participants 8 messages Jul 24, 2009 – Aug 19, 2009

lore
Share & tools
lore
#0 lore raw

Hello,

I have a dual Xeon server (old Xeon HT) with an Intel E7505 chipset, with hrtimer and dynticks enabled. On bootup, the kernel (2.6.29-gentoo-r5) tells me it's using the PM-Timer bug workaround, but then it uses tsc as clocksource. Now the clock was running slow for about 15sec/12hrs, which is quite a lot. So in a careless moment, I just tried "echo jiffies > clocksource0/current_clocksource". This froze the system time. Now I couldn't switch back to tsc or acpi_pm, echoing those was just ignored. Subsequently, the entire system locked up and I needed to reboot.

Now what does that mean? Is this supposed to happen? Should I disable dynticks and/or hrtimer?

thanks...

Signature · 8 lines
Victor Mataré
Server- & Netzwerk-Administration

Lehrstuhl für Ingenieurgeologie und Hydrogeologie der RWTH-Aachen
Lochnerstraße 4-20, 52064 Aachen

Tel: 0241 80 96778
Fax: 0241 80 92280
#1 lore raw
Quoted 10 lines · Victor Mataré

I have a dual Xeon server (old Xeon HT) with an Intel E7505 chipset, with hrtimer and dynticks enabled. On bootup, the kernel (2.6.29-gentoo-r5) tells me it's using the PM-Timer bug workaround, but then it uses tsc as clocksource. Now the clock was running slow for about 15sec/12hrs, which is quite a lot. So in a careless moment, I just tried "echo jiffies > clocksource0/current_clocksource". This froze the system time. Now I couldn't switch back to tsc or acpi_pm, echoing those was just ignored. Subsequently, the entire system locked up and I needed to reboot.

Quoted 2 lines

Now what does that mean? Is this supposed to happen? Should I disable dynticks and/or hrtimer?

The system lockup is a known issue and should be resolved with the following commit:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3f68535adad8dd89499505a65fb25d0e02d118cc

I might be curious if you could expand a bit more about the clock skew (15sec per 12 hours) you're seeing. Are you running NTP? Do you have the output of ntpdc -c kerninfo , ntpdc -c peers? Do you see lots of ntp messages in /var/log/messages or /var/log/syslog ?

thanks
-john

#2 lore raw
Quoted 18 lines · john stultz
Quoted 10 lines · Victor Mataré

I have a dual Xeon server (old Xeon HT) with an Intel E7505 chipset, with hrtimer and dynticks enabled. On bootup, the kernel (2.6.29-gentoo-r5) tells me it's using the PM-Timer bug workaround, but then it uses tsc as clocksource. Now the clock was running slow for about 15sec/12hrs, which is quite a lot. So in a careless moment, I just tried "echo jiffies > clocksource0/current_clocksource". This froze the system time. Now I couldn't switch back to tsc or acpi_pm, echoing those was just ignored. Subsequently, the entire system locked up and I needed to reboot.

Quoted 2 lines

Now what does that mean? Is this supposed to happen? Should I disable dynticks and/or hrtimer?

The system lockup is a known issue and should be resolved with the following commit:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3f68535adad8dd89499505a65fb25d0e02d118cc

Quoted 7 lines

I might be curious if you could expand a bit more about the clock skew (15sec per 12 hours) you're seeing. Are you running NTP? Do you have the output of ntpdc -c kerninfo , ntpdc -c peers? Do you see lots of ntp messages in /var/log/messages or /var/log/syslog ?

thanks
-john

Until now, I was just using BSD netdate, which kept adding 12-25 seconds every 24 hours.
The whole issue is related to strange lockups I had been seeing about monthly, apparently everytime the clock was rewound instead of put forward (clock freezes, programs hang, system ends up deadlocked within 10-300 minutes depending on usage). The system is a production fileserver acting mainly as a Samba PDC, so testing this scenario is quite difficult. Now recently, I swapped the motherboard including RAM and CPU with our webserver, which seems to have removed the monthly time-freeze, but led to the above-mentioned freeze caused by me experimenting with clocksource=jiffies because of the slow clock. However, the monthly freezes upon rewinding the clock may be gone now just because the clock is consistently running slow, so it doesn't need to be rewound any more.
I've just switched both systems to ntpd:

# ntpdc -c kerninfo
pll offset:           0 s
pll frequency:        0.000 ppm
maximum error:        16 s
estimated error:      16 s
status:               0040  unsync
pll time constant:    4
precision:            1e-06 s
frequency tolerance:  500 ppm
# ntpdc -c peers -n
     remote           local      st poll reach  delay   offset    disp
=======================================================================
=134.130.4.17    137.226.164.2    1   64  377 0.00061  0.156253 0.03084
*134.130.5.17    137.226.164.2    1   64  377 0.00035  0.205312 0.03041

Dunno how to interpret that. Syslog now gives:

Aug 11 17:13:02 bussard ntpd[21845]: ntpd [email protected] Tue Jun 23
10:58:51 UTC 2009 (1)
Aug 11 17:13:02 bussard ntpd[21874]: precision = 1.000 usec
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #0 wildcard,
0.0.0.0#123 Disabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #1 lo,
127.0.0.1#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #2 eth0,
137.226.164.2#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #3 eth0:1,
192.168.23.3#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: kernel time sync status 0040
...
Aug 11 17:16:18 bussard ntpd[21874]: synchronized to 134.130.4.17, stratum 1
Aug 11 17:16:32 bussard ntpd[21874]: time reset +13.979355 s
...
Aug 11 17:20:43 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1

However, the issue of the clock freezing upon time-rewind still remains quite unclear to me. Can it be caused by the careless way in which netdate does it? Can it be related to the jiffies-hrtimer issue?

Thanks for your help so far, I'll be back when I know more. Victor

#3 lore raw
Quoted 43 lines · Victor Mataré
Quoted 18 lines · john stultz
Quoted 10 lines · Victor Mataré

I have a dual Xeon server (old Xeon HT) with an Intel E7505 chipset, with hrtimer and dynticks enabled. On bootup, the kernel (2.6.29-gentoo-r5) tells me it's using the PM-Timer bug workaround, but then it uses tsc as clocksource. Now the clock was running slow for about 15sec/12hrs, which is quite a lot. So in a careless moment, I just tried "echo jiffies > clocksource0/current_clocksource". This froze the system time. Now I couldn't switch back to tsc or acpi_pm, echoing those was just ignored. Subsequently, the entire system locked up and I needed to reboot.

Quoted 2 lines

Now what does that mean? Is this supposed to happen? Should I disable dynticks and/or hrtimer?

The system lockup is a known issue and should be resolved with the following commit:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3f68535adad8dd89499505a65fb25d0e02d118cc

Quoted 7 lines

I might be curious if you could expand a bit more about the clock skew (15sec per 12 hours) you're seeing. Are you running NTP? Do you have the output of ntpdc -c kerninfo , ntpdc -c peers? Do you see lots of ntp messages in /var/log/messages or /var/log/syslog ?

thanks
-john

Until now, I was just using BSD netdate, which kept adding 12-25 seconds every 24 hours.
The whole issue is related to strange lockups I had been seeing about monthly, apparently everytime the clock was rewound instead of put forward (clock freezes, programs hang, system ends up deadlocked within 10-300 minutes depending on usage). The system is a production fileserver acting mainly as a Samba PDC, so testing this scenario is quite difficult. Now recently, I swapped the motherboard including RAM and CPU with our webserver, which seems to have removed the monthly time-freeze, but led to the above-mentioned freeze caused by me experimenting with clocksource=jiffies because of the slow clock. However, the monthly freezes upon rewinding the clock may be gone now just because the clock is consistently running slow, so it doesn't need to be rewound any more.
I've just switched both systems to ntpd:

Quoted 9 lines
# ntpdc -c kerninfo
pll offset:           0 s
pll frequency:        0.000 ppm
maximum error:        16 s
estimated error:      16 s
status:               0040  unsync
pll time constant:    4
precision:            1e-06 s
frequency tolerance:  500 ppm

So here its reporting you're still in unsync mode, so ntp hasn't run long enough to do any corrections. You might let the system run with ntpd for a few hours (or a day) and then try re-try the "ntpdc -c kerninfo" command.

Quoted 17 lines
# ntpdc -c peers -n
     remote           local      st poll reach  delay   offset    disp
=======================================================================
=134.130.4.17    137.226.164.2    1   64  377 0.00061  0.156253 0.03084
*134.130.5.17    137.226.164.2    1   64  377 0.00035  0.205312 0.03041

Dunno how to interpret that. Syslog now gives:

Aug 11 17:13:02 bussard ntpd[21845]: ntpd [email protected] Tue Jun 23
10:58:51 UTC 2009 (1)
Aug 11 17:13:02 bussard ntpd[21874]: precision = 1.000 usec
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #0 wildcard,
0.0.0.0#123 Disabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #1 lo,
127.0.0.1#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #2 eth0,

137.226.164.2#123 Enabled

Quoted 8 lines
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #3 eth0:1,
192.168.23.3#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: kernel time sync status 0040
...
Aug 11 17:16:18 bussard ntpd[21874]: synchronized to 134.130.4.17, stratum 1
Aug 11 17:16:32 bussard ntpd[21874]: time reset +13.979355 s
...
Aug 11 17:20:43 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1

I'd also be interested in seeing the syslog data as well after a day or so of running ntpd.

Quoted 3 lines

However, the issue of the clock freezing upon time-rewind still remains quite unclear to me. Can it be caused by the careless way in which netdate does it? Can it be related to the jiffies-hrtimer issue?

I'm not familiar with netdate, however the time should be able to be set in either forward or backward direction without the system hanging.

Can you trigger the problem yourself using date -s ?

thanks
-john

#4 lore raw
Quoted 93 lines · john stultz
Quoted 41 lines · Victor Mataré
Quoted 17 lines · john stultz
Quoted 10 lines · Victor Mataré

I have a dual Xeon server (old Xeon HT) with an Intel E7505 chipset, with hrtimer and dynticks enabled. On bootup, the kernel (2.6.29-gentoo-r5) tells me it's using the PM-Timer bug workaround, but then it uses tsc as clocksource. Now the clock was running slow for about 15sec/12hrs, which is quite a lot. So in a careless moment, I just tried "echo jiffies > clocksource0/current_clocksource". This froze the system time. Now I couldn't switch back to tsc or acpi_pm, echoing those was just ignored. Subsequently, the entire system locked up and I needed to reboot.

Quoted 2 lines

Now what does that mean? Is this supposed to happen? Should I disable dynticks and/or hrtimer?

The system lockup is a known issue and should be resolved with the following commit:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3f68535adad8dd89499505a65fb25d0e02d118cc

Quoted 7 lines

I might be curious if you could expand a bit more about the clock skew (15sec per 12 hours) you're seeing. Are you running NTP? Do you have the output of ntpdc -c kerninfo , ntpdc -c peers? Do you see lots of ntp messages in /var/log/messages or /var/log/syslog ?

thanks
-john

Until now, I was just using BSD netdate, which kept adding 12-25 seconds every 24 hours.
The whole issue is related to strange lockups I had been seeing about monthly, apparently everytime the clock was rewound instead of put forward (clock freezes, programs hang, system ends up deadlocked within 10-300 minutes depending on usage). The system is a production fileserver acting mainly as a Samba PDC, so testing this scenario is quite difficult. Now recently, I swapped the motherboard including RAM and CPU with our webserver, which seems to have removed the monthly time-freeze, but led to the above-mentioned freeze caused by me experimenting with clocksource=jiffies because of the slow clock. However, the monthly freezes upon rewinding the clock may be gone now just because the clock is consistently running slow, so it doesn't need to be rewound any more.
I've just switched both systems to ntpd:

Quoted 9 lines
# ntpdc -c kerninfo
pll offset:           0 s
pll frequency:        0.000 ppm
maximum error:        16 s
estimated error:      16 s
status:               0040  unsync
pll time constant:    4
precision:            1e-06 s
frequency tolerance:  500 ppm

So here its reporting you're still in unsync mode, so ntp hasn't run long enough to do any corrections. You might let the system run with ntpd for a few hours (or a day) and then try re-try the "ntpdc -c kerninfo" command.

Quoted 17 lines
# ntpdc -c peers -n
     remote           local      st poll reach  delay   offset    disp
=======================================================================
=134.130.4.17    137.226.164.2    1   64  377 0.00061  0.156253 0.03084
*134.130.5.17    137.226.164.2    1   64  377 0.00035  0.205312 0.03041

Dunno how to interpret that. Syslog now gives:

Aug 11 17:13:02 bussard ntpd[21845]: ntpd [email protected] Tue Jun 23
10:58:51 UTC 2009 (1)
Aug 11 17:13:02 bussard ntpd[21874]: precision = 1.000 usec
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #0 wildcard,
0.0.0.0#123 Disabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #1 lo,
127.0.0.1#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #2 eth0,

137.226.164.2#123 Enabled

Quoted 8 lines
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #3 eth0:1,
192.168.23.3#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: kernel time sync status 0040
...
Aug 11 17:16:18 bussard ntpd[21874]: synchronized to 134.130.4.17, stratum 1
Aug 11 17:16:32 bussard ntpd[21874]: time reset +13.979355 s
...
Aug 11 17:20:43 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1

I'd also be interested in seeing the syslog data as well after a day or so of running ntpd.

Quoted 3 lines

However, the issue of the clock freezing upon time-rewind still remains quite unclear to me. Can it be caused by the careless way in which netdate does it? Can it be related to the jiffies-hrtimer issue?

Quoted 8 lines

I'm not familiar with netdate, however the time should be able to be set in either forward or backward direction without the system hanging.

Can you trigger the problem yourself using date -s ?

thanks
-john

OK, ntpd has been running for a week now, and I'm not sure what it has been doing. Last week, on the day I set it up, there was this:

# grep ntpd\\[ /var/log/syslog
Aug 11 17:16:18 bussard ntpd[21874]: synchronized to 134.130.4.17, stratum 1
Aug 11 17:16:32 bussard ntpd[21874]: time reset +13.979355 s
Aug 11 17:20:43 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 11 17:32:31 bussard ntpd[21874]: time reset +0.300276 s
Aug 11 17:32:31 bussard ntpd[21874]: kernel time sync status change 0001
Aug 11 17:36:27 bussard ntpd[21874]: synchronized to 134.130.4.17, stratum 1
Aug 11 17:40:56 bussard ntpd[21874]: no servers reachable
Aug 11 18:32:16 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 11 18:32:16 bussard ntpd[21874]: kernel time sync status change 4001

Now after that, up until today, I see only this:

Aug 17 18:43:42 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 17 18:50:28 bussard ntpd[21874]: kernel time sync status change 0001
Aug 17 19:17:50 bussard ntpd[21874]: no servers reachable
Aug 17 20:09:06 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 17 20:09:06 bussard ntpd[21874]: kernel time sync status change 4001
Aug 17 20:32:56 bussard ntpd[21874]: kernel time sync status change 0001
Aug 17 20:43:17 bussard ntpd[21874]: no servers reachable
Aug 17 23:06:35 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 17 23:06:35 bussard ntpd[21874]: kernel time sync status change 4001
Aug 17 23:16:53 bussard ntpd[21874]: no servers reachable
Aug 18 11:48:13 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 18 12:05:18 bussard ntpd[21874]: no servers reachable
Aug 18 14:11:32 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 18 14:21:57 bussard ntpd[21874]: no servers reachable
# grep ntpd\\[ /var/log/syslog | wc
    177    1737   12413
(Starting from August 11, when I set up ntpd)
# ntpdc -c kerninfo
pll offset:           -0.002368 s
pll frequency:        272.989 ppm
maximum error:        1.51074 s
estimated error:      0.003472 s
status:               4001  pll
pll time constant:    10
precision:            1e-06 s
frequency tolerance:  500 ppm

Now I guess it does adjust the time quite frequently, although it doesn't tell me the differences in syslog, right? At least all servers are nicely synchronized in time, now.

However, I've never been able to manually trigger that regular time-freeze that occurred about monthly. Note that above data are from the system that did not experience that monthly freeze, but did freeze on the "echo jiffies > current_clocksource" thing.
On the system that did freeze spontaneously syslog looks just about the same, with:

# grep "ntpd\[" syslog | wc
    199    1934   13332

and:

# ntpdc -c kerninfo
pll offset:           -0.055492 s
pll frequency:        -164.169 ppm
maximum error:        1.14918 s
estimated error:      0.018156 s
status:               4001  pll
pll time constant:    10
precision:            1e-06 s
frequency tolerance:  500 ppm

Now I might be inclined to account the apparently higher deviation to the higher CPU clock this system uses (2x Xeon HT 3.06 GHz on Intel E7501 vs. 2x Xeon HT 2.4 GHz on Intel E7505 in the first system. Both have clocksource=tsc).

I'm sorry for the long delay, but my working time in this place is very limited. I'd really appreciate some ideas on how I might:
- Narrow in on the problem once I get so lucky as to witness the machine freezing...
- Trigger the timer freeze with something other than the jiffies thing

Both systems have now been up for 20, resp. 25 days, so the monthly freeze (if it does occur now after swapping the mainboards) is to be expected within the next 10 days.

Great thanks for your help and interest in this problem.

Signature · 8 lines
Victor Mataré
Server- & Netzwerk-Administration

Lehrstuhl für Ingenieurgeologie und Hydrogeologie der RWTH-Aachen
Lochnerstraße 4-20, 52064 Aachen

Tel: 0241 80 96778
Fax: 0241 80 92280
#5 lore raw
Quoted 148 lines · Victor Mataré
Quoted 93 lines · john stultz
Quoted 41 lines · Victor Mataré
Quoted 17 lines · john stultz
Quoted 10 lines · Victor Mataré

I have a dual Xeon server (old Xeon HT) with an Intel E7505 chipset, with hrtimer and dynticks enabled. On bootup, the kernel (2.6.29-gentoo-r5) tells me it's using the PM-Timer bug workaround, but then it uses tsc as clocksource. Now the clock was running slow for about 15sec/12hrs, which is quite a lot. So in a careless moment, I just tried "echo jiffies > clocksource0/current_clocksource". This froze the system time. Now I couldn't switch back to tsc or acpi_pm, echoing those was just ignored. Subsequently, the entire system locked up and I needed to reboot.

Quoted 2 lines

Now what does that mean? Is this supposed to happen? Should I disable dynticks and/or hrtimer?

The system lockup is a known issue and should be resolved with the following commit:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3f68535adad8dd89499505a65fb25d0e02d118cc

Quoted 7 lines

I might be curious if you could expand a bit more about the clock skew (15sec per 12 hours) you're seeing. Are you running NTP? Do you have the output of ntpdc -c kerninfo , ntpdc -c peers? Do you see lots of ntp messages in /var/log/messages or /var/log/syslog ?

thanks
-john

Until now, I was just using BSD netdate, which kept adding 12-25 seconds every 24 hours.
The whole issue is related to strange lockups I had been seeing about monthly, apparently everytime the clock was rewound instead of put forward (clock freezes, programs hang, system ends up deadlocked within 10-300 minutes depending on usage). The system is a production fileserver acting mainly as a Samba PDC, so testing this scenario is quite difficult. Now recently, I swapped the motherboard including RAM and CPU with our webserver, which seems to have removed the monthly time-freeze, but led to the above-mentioned freeze caused by me experimenting with clocksource=jiffies because of the slow clock. However, the monthly freezes upon rewinding the clock may be gone now just because the clock is consistently running slow, so it doesn't need to be rewound any more.
I've just switched both systems to ntpd:

Quoted 9 lines
# ntpdc -c kerninfo
pll offset:           0 s
pll frequency:        0.000 ppm
maximum error:        16 s
estimated error:      16 s
status:               0040  unsync
pll time constant:    4
precision:            1e-06 s
frequency tolerance:  500 ppm

So here its reporting you're still in unsync mode, so ntp hasn't run long enough to do any corrections. You might let the system run with ntpd for a few hours (or a day) and then try re-try the "ntpdc -c kerninfo" command.

Quoted 17 lines
# ntpdc -c peers -n
     remote           local      st poll reach  delay   offset    disp
=======================================================================
=134.130.4.17    137.226.164.2    1   64  377 0.00061  0.156253 0.03084
*134.130.5.17    137.226.164.2    1   64  377 0.00035  0.205312 0.03041

Dunno how to interpret that. Syslog now gives:

Aug 11 17:13:02 bussard ntpd[21845]: ntpd [email protected] Tue Jun 23
10:58:51 UTC 2009 (1)
Aug 11 17:13:02 bussard ntpd[21874]: precision = 1.000 usec
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #0 wildcard,
0.0.0.0#123 Disabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #1 lo,
127.0.0.1#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #2 eth0,

137.226.164.2#123 Enabled

Quoted 8 lines
Aug 11 17:13:02 bussard ntpd[21874]: Listening on interface #3 eth0:1,
192.168.23.3#123 Enabled
Aug 11 17:13:02 bussard ntpd[21874]: kernel time sync status 0040
...
Aug 11 17:16:18 bussard ntpd[21874]: synchronized to 134.130.4.17, stratum 1
Aug 11 17:16:32 bussard ntpd[21874]: time reset +13.979355 s
...
Aug 11 17:20:43 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1

I'd also be interested in seeing the syslog data as well after a day or so of running ntpd.

Quoted 3 lines

However, the issue of the clock freezing upon time-rewind still remains quite unclear to me. Can it be caused by the careless way in which netdate does it? Can it be related to the jiffies-hrtimer issue?

Quoted 8 lines

I'm not familiar with netdate, however the time should be able to be set in either forward or backward direction without the system hanging.

Can you trigger the problem yourself using date -s ?

thanks
-john

OK, ntpd has been running for a week now, and I'm not sure what it has been doing. Last week, on the day I set it up, there was this:

# grep ntpd\\[ /var/log/syslog
Aug 11 17:16:18 bussard ntpd[21874]: synchronized to 134.130.4.17, stratum 1
Aug 11 17:16:32 bussard ntpd[21874]: time reset +13.979355 s
Aug 11 17:20:43 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 11 17:32:31 bussard ntpd[21874]: time reset +0.300276 s
Aug 11 17:32:31 bussard ntpd[21874]: kernel time sync status change 0001
Aug 11 17:36:27 bussard ntpd[21874]: synchronized to 134.130.4.17, stratum 1
Aug 11 17:40:56 bussard ntpd[21874]: no servers reachable
Aug 11 18:32:16 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 11 18:32:16 bussard ntpd[21874]: kernel time sync status change 4001

Now after that, up until today, I see only this:

Aug 17 18:43:42 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 17 18:50:28 bussard ntpd[21874]: kernel time sync status change 0001
Aug 17 19:17:50 bussard ntpd[21874]: no servers reachable
Aug 17 20:09:06 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 17 20:09:06 bussard ntpd[21874]: kernel time sync status change 4001
Aug 17 20:32:56 bussard ntpd[21874]: kernel time sync status change 0001
Aug 17 20:43:17 bussard ntpd[21874]: no servers reachable
Aug 17 23:06:35 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 17 23:06:35 bussard ntpd[21874]: kernel time sync status change 4001
Aug 17 23:16:53 bussard ntpd[21874]: no servers reachable
Aug 18 11:48:13 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 18 12:05:18 bussard ntpd[21874]: no servers reachable
Aug 18 14:11:32 bussard ntpd[21874]: synchronized to 134.130.5.17, stratum 1
Aug 18 14:21:57 bussard ntpd[21874]: no servers reachable
# grep ntpd\\[ /var/log/syslog | wc
    177    1737   12413
(Starting from August 11, when I set up ntpd)
# ntpdc -c kerninfo
pll offset:           -0.002368 s
pll frequency:        272.989 ppm
maximum error:        1.51074 s
estimated error:      0.003472 s
status:               4001  pll
pll time constant:    10
precision:            1e-06 s
frequency tolerance:  500 ppm
Quoted 3 lines

Now I guess it does adjust the time quite frequently, although it doesn't tell me the differences in syslog, right? At least all servers are nicely synchronized in time, now.

It is slewing the clock instead of setting it, and the log messages seem to either be due to the time server becoming unreachable (network outage?) periodically.

Quoted 27 lines

However, I've never been able to manually trigger that regular time-freeze that occurred about monthly. Note that above data are from the system that did not experience that monthly freeze, but did freeze on the "echo jiffies > current_clocksource" thing.
On the system that did freeze spontaneously syslog looks just about the same, with:

# grep "ntpd\[" syslog | wc
    199    1934   13332

and:

# ntpdc -c kerninfo
pll offset:           -0.055492 s
pll frequency:        -164.169 ppm
maximum error:        1.14918 s
estimated error:      0.018156 s
status:               4001  pll
pll time constant:    10
precision:            1e-06 s
frequency tolerance:  500 ppm

Now I might be inclined to account the apparently higher deviation to the higher CPU clock this system uses (2x Xeon HT 3.06 GHz on Intel E7501 vs. 2x Xeon HT 2.4 GHz on Intel E7505 in the first system. Both have clocksource=tsc).

Quoted 5 lines

I'm sorry for the long delay, but my working time in this place is very limited. I'd really appreciate some ideas on how I might:
- Narrow in on the problem once I get so lucky as to witness the machine freezing...
- Trigger the timer freeze with something other than the jiffies thing

Yes, the jiffies thing is a different issue entirely and has been fixed upstream.

I am interested in the hang you describe, but from the logs above it looks like things are functioning properly.

Quoted 3 lines

Both systems have now been up for 20, resp. 25 days, so the monthly freeze (if it does occur now after swapping the mainboards) is to be expected within the next 10 days.

Do let me know if you continue to see it.

thanks
-john

#7 lore raw
Quoted 3 lines · Victor Mataré

just to be clear:

Quoted 1 line

Can you trigger the problem yourself using date -s ?

nope.

Ok. Then I suspect the hang isn't ntp related, but we'll keep watching it.

thanks
-john