Skip to contentSkip to conversation

(EC168) PC Basic TNT USB Basic V5 ( France ) recognized but no channel tuning

DISCUSSION Morvan Le Meut 3 participants 7 messages Sep 2, 2009 – Sep 3, 2009 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

Hello
I've just bough that and it seems that the EC168 driver can't work with it ( yet )
The PCB identifies itself as a ForwardVideo "EzTV818_D.". Work with a EC168 and a MXL5003S ( no doubt about it, but it is barely legible, and since i've no camera, no PCB picture available ). ( and the EC168BDA.bin firmware is provided on the CD )

A typical dmesg for it :

[19715.764919] usb 2-1.1: new high speed USB device using ehci_hcd and
address 8
[19715.873356] usb 2-1.1: configuration #1 chosen from 1 choice
[19715.878085] dvb-usb: found a 'E3C EC168 DVB-T USB2.0 reference
design' in cold state, will try to load a firmware
[19715.878096] firmware: requesting dvb-usb-ec168.fw
[19715.929889] dvb-usb: downloading firmware from file 'dvb-usb-ec168.fw'
[19715.985884] dvb-usb: found a 'E3C EC168 DVB-T USB2.0 reference
design' in warm state.
[19715.985958] dvb-usb: will pass the complete MPEG2 transport stream to
the software demuxer.
[19715.986487] DVB: registering new adapter (E3C EC168 DVB-T USB2.0
reference design)
[19715.986931] DVB: registering adapter 1 frontend 0 (E3C EC100 DVB-T)...
[19715.987045] MXL5005S: Attached at address 0xc6
[19715.987052] dvb-usb: E3C EC168 DVB-T USB2.0 reference design
successfully initialized and connected.
[19716.004730] dvb-usb: found a 'E3C EC168 DVB-T USB2.0 reference
design' in warm state.
[19716.004799] dvb-usb: will pass the complete MPEG2 transport stream to
the software demuxer.
[19716.010131] DVB: registering new adapter (E3C EC168 DVB-T USB2.0
reference design)
[19716.010499] DVB: registering adapter 2 frontend 0 (E3C EC100 DVB-T)...
[19716.010612] MXL5005S: Attached at address 0xc6
[19716.010619] dvb-usb: E3C EC168 DVB-T USB2.0 reference design
successfully initialized and connected.
[19716.010729] usb 2-1.1: New USB device found, idVendor=18b4,
idProduct=1001
[19716.010733] usb 2-1.1: New USB device strings: Mfr=0, Product=0,

SerialNumber=0

To be perfectly honest a previous attempt didn't have the "New USB device" at the end, but the result was the same : no tuning possible ( "WARNING: >>> tuning failed!!!" ) even if there is a device file for it in /dev/ ( on a Linux debian 2.6.26-2-686 #1 SMP Fri Aug 14 01:27:18 UTC 2009 i686 GNU/Linux with V4L/DVB driver using mercurial ). I've checked the antenna cable ( my old Intuix S800 work perfectly in the same setup but it does not have a remote :) )

Thanks for any info/tips.

#1 lore raw
Quoted 6 lines · Morvan Le Meut

I've just bough that and it seems that the EC168 driver can't work with it ( yet )
The PCB identifies itself as a ForwardVideo "EzTV818_D.". Work with a EC168 and a MXL5003S ( no doubt about it, but it is barely legible, and since i've no camera, no PCB picture available ). ( and the EC168BDA.bin firmware is provided on the CD )

Did you used the firmware from the CD? It will not work because it does not have "warm" USB ID, it is all zero and due to that device will disappear from driver perspective. You should use that firmware:
http://palosaari.fi/linux/v4l-dvb/firmware/ec168/

Antti

Signature · 1 line
http://palosaari.fi/
#2 lore raw
Quoted 6 lines · Antti Palosaari

Did you used the firmware from the CD? It will not work because it does not have "warm" USB ID, it is all zero and due to that device will disappear from driver perspective. You should use that firmware:
http://palosaari.fi/linux/v4l-dvb/firmware/ec168/

Antti

I tried both with the same result. ( I'm not ruling out user error since i've a similar problem with an HVR 1110 (sold as a 1100 ) but it is strange that only my newest TV cards have problems ). Maybe i should try it with Windows to check if the card itself works.

#3 lore raw

Am Donnerstag, den 03.09.2009, 01:00 +0200 schrieb Morvan Le Meut:

Quoted 8 lines
Quoted 7 lines · Antti Palosaari

Did you used the firmware from the CD? It will not work because it does not have "warm" USB ID, it is all zero and due to that device will disappear from driver perspective.
You should use that firmware:
http://palosaari.fi/linux/v4l-dvb/firmware/ec168/

Quoted 6 lines
Quoted 1 line

Antti

I tried both with the same result. ( I'm not ruling out user error since i've a similar problem with an HVR 1110 (sold as a 1100 ) but it is strange that only my newest TV cards have problems ). Maybe i should try it with Windows to check if the card itself works.

Hi Morvan,

HVR 1100 and HVR 1110 are totally different boards.

How does GNU/Linux detect the board on your recent kernel?

Sorry, I might be in delay reading previous messages.

Even on the HVR 1110 we have unclear situations, concerning that some of them might have an additional LowNoiseAmplifier, which needs to be configured correctly, and others not.

It might even be the case, that there are at least three different types of such LNAs recently, and we don't know how to detect them.

All needing a different setup.

Please copy/paste device related dmesg output.

I still have not give up on it, that we might be able to identify those different devices in the future.

Until somebody tells me better ...

Cheers,
Hermann

#4 lore raw
Quoted 19 lines · hermann pitton

Hi Morvan,

HVR 1100 and HVR 1110 are totally different boards.

How does GNU/Linux detect the board on your recent kernel?

Sorry, I might be in delay reading previous messages.

Even on the HVR 1110 we have unclear situations, concerning that some of them might have an additional LowNoiseAmplifier, which needs to be configured correctly, and others not.

It might even be the case, that there are at least three different types of such LNAs recently, and we don't know how to detect them.

All needing a different setup.

Please copy/paste device related dmesg output.

Quoted 10 lines

I still have not give up on it, that we might be able to identify those different devices in the future.

Until somebody tells me better ...

Cheers,
Hermann

it is a 1110 one ( triangular shaped ) but it may be a new design or something else. I don't have it here for the moment so i can't give exact info but i tried the "card=104" and "card=156" options ( no autodetection ) with no result ( analog TV and DVB didn't work ). ( In the meantime, it's back in its box, waiting for a day where it will work with my mythbuntu box :) )

#6 lore raw
In reply to Morvan Le Meut
Quoted 8 lines · Morvan Le Meut

I tried both with the same result. ( I'm not ruling out user error since i've a similar problem with an HVR 1110 (sold as a 1100 ) but it is strange that only my newest TV cards have problems ). Maybe i should try it with Windows to check if the card itself works.

Signature · 3 lines
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

tried it under windows : the card work, so it's a driver problem. ( I forgot how horrible DVB software under windows is, too )

#5 lore raw
In reply to Morvan Le Meut

Am Donnerstag, den 03.09.2009, 07:40 +0200 schrieb Morvan Le Meut:

Quoted 30 lines
Quoted 19 lines · hermann pitton

Hi Morvan,

HVR 1100 and HVR 1110 are totally different boards.

How does GNU/Linux detect the board on your recent kernel?

Sorry, I might be in delay reading previous messages.

Even on the HVR 1110 we have unclear situations, concerning that some of them might have an additional LowNoiseAmplifier, which needs to be configured correctly, and others not.

It might even be the case, that there are at least three different types of such LNAs recently, and we don't know how to detect them.

All needing a different setup.

Please copy/paste device related dmesg output.

Quoted 10 lines

I still have not give up on it, that we might be able to identify those different devices in the future.

Until somebody tells me better ...

Cheers,
Hermann

Quoted 7 lines

it is a 1110 one ( triangular shaped ) but it may be a new design or something else. I don't have it here for the moment so i can't give exact info but i tried the "card=104" and "card=156" options ( no autodetection ) with no result ( analog TV and DVB didn't work ).
( In the meantime, it's back in its box, waiting for a day where it
will work with my mythbuntu box :) )

Without knowing the kernel version on your mythbuntu I can't tell anything.

For what I know so far, all HVR 1110 variants should be supported with recent v4l-dvb code.

We run into some maintenance trouble, because we don't know on which of those are additional LNAs, maybe even different types of LNAs.

Currently it looks like that we have some Pinnacle 310i devices broken in favour to have in detail unknown HVR 1110 boards working with LNA support.

It would be much better to escape from such and not to add more and more unclear hardware on it.

For broken Pinnacle LNA devices are patches to test available to get them back, others still do work unchanged, also to enable antenna voltage for those in need of it is possible.

You should try your HVR 1110 variant with recent code and report again with details from dmesg for it, if it still should fail.

Cheers,
Hermann