Skip to contentSkip to conversation

USB device support for OMAP3

U-Boot Tom 3 participants 3 messages Sep 4, 2009 – Sep 5, 2009

lore
Share & tools
lore

Tom

author
#0 lore raw

The recently posted patches enable usb device support for omap3 They are against the repository http://git.denx.de/u-boot-arm.git,
branch 'next'

You can also view them in my development tree
http://dev.omapzoom.org/?p=trix/u-boot.git;a=shortlog;h=refs/heads/arm-next-development
starting at commit 50031bc80615f4fcafcdc613020b87a326aaed92

The device support was usbtty.
This was run tested on beagle, zoom1 and zoom2.
The maintainer of the beagle and zoom1 boards should decide if they want a usb device
starting for their board.
For zoom2, the usbtty is the console when the debug board is not present.

There were some small changes to the musb common code. The devinci maintainer should check that their host support is ok.

There is a large change to usb structures that should be also tested out. I ran this through MAKEALL arm, mips and ppc but I do not have a board that uses
usb in host mode.

After this I plan on submitting a new usb device called 'fastboot' It provides a limited set of basic commands to help develop over just usb. Here is a link.
https://gforge.ti.com/gf/project/omapzoom/wiki/?pagename=FAQ-8%3A+Zoom-II+Android%C2%A0fastboot

Tom

#1 lore raw

Tom

Quoted 9 lines

-----Original Message-----
From: Tom [mailto:Tom.Rix at windriver.com]
Sent: Friday, September 04, 2009 3:22 PM
To: u-boot at lists.denx.de; Dirk Behme; Menon, Nishanth; t-abraham at ti.com
Subject: USB device support for OMAP3

The recently posted patches enable usb device support for omap3 They are against the repository http://git.denx.de/u-boot-arm.git,
branch 'next'

This is real good work to enable all OMAP platforms to have complete USB device support.

This opens up lots of possibilities to make OMAP work as different USB devices in u-boot:
Ethernet, Mass Storage, Fastboot, Serial, Audio etc etc....

Lets see how much community leverages from your good work...

Quoted 32 lines

You can also view them in my development tree
http://dev.omapzoom.org/?p=trix/u-boot.git;a=shortlog;h=refs/heads/arm-next-development
starting at commit 50031bc80615f4fcafcdc613020b87a326aaed92

The device support was usbtty.
This was run tested on beagle, zoom1 and zoom2.
The maintainer of the beagle and zoom1 boards should decide if they want a usb device
starting for their board.
For zoom2, the usbtty is the console when the debug board is not present.

There were some small changes to the musb common code. The devinci maintainer should check that their host support is ok.

There is a large change to usb structures that should be also tested out. I ran this through MAKEALL arm, mips and ppc but I do not have a board that uses
usb in host mode.

After this I plan on submitting a new usb device called 'fastboot' It provides a limited set of basic commands to help develop over just usb. Here is a link.
https://gforge.ti.com/gf/project/omapzoom/wiki/?pagename=FAQ-8%3A+Zoom-II+Android%C2%A0fastboot

Tom

#2 lore raw
In reply to Tom
Quoted 7 lines · Tom

The recently posted patches enable usb device support for omap3 They are against the repository http://git.denx.de/u-boot-arm.git,
branch 'next'

You can also view them in my development tree
http://dev.omapzoom.org/?p=trix/u-boot.git;a=shortlog;h=refs/heads/arm-next-development

Quoted 7 lines

starting at commit 50031bc80615f4fcafcdc613020b87a326aaed92

The device support was usbtty.
This was run tested on beagle, zoom1 and zoom2.
The maintainer of the beagle and zoom1 boards should decide if they want a usb device
starting for their board.

Great work!

Yes, I think we want this :)

Best regards

Dirk

Quoted 16 lines

For zoom2, the usbtty is the console when the debug board is not present.

There were some small changes to the musb common code. The devinci maintainer should check that their host support is ok.

There is a large change to usb structures that should be also tested out. I ran this through MAKEALL arm, mips and ppc but I do not have a board that uses
usb in host mode.
After this I plan on submitting a new usb device called 'fastboot' It provides a limited set of basic commands to help develop over just usb. Here is a link.
https://gforge.ti.com/gf/project/omapzoom/wiki/?pagename=FAQ-8%3A+Zoom-II+Android%C2%A0fastboot

Tom