Staging: cpc-usb CAN driver TODO list
Subsystems (2)
Hello Greg and Sebastian,
i just looked around in the linux-next tree for the cpc-usb driver.
IMHO the sja2m16c* files are completely obsolete as the setting of the CAN bittimings needs to be done by separate functions (one for the SJA1000 and one for the M16C). For both of them a separate can_bittiming_const is needed, like it is defined in drivers/net/can/sja1000/sja1000.c:
static struct can_bittiming_const sja1000_bittiming_const = {
.name = DRV_NAME,
.tseg1_min = 1,
.tseg1_max = 16,
.tseg2_min = 1,
.tseg2_max = 8,
.sjw_max = 4,
.brp_min = 1,
.brp_max = 64,
.brp_inc = 1,
};Also a separate function to determine the register values from the calculated bittiming values is needed for both hardware types (SJA1000(LPC2119)/M16C) of the cpc-usb. How this is done can be checked in linux/drivers/net/can/* or in the source code of upcoming drivers in
http://svn.berlios.de/svnroot/repos/socketcan/trunk/kernel/2.6/drivers/net/can/
I wondered about the following items in the TODO list:
- tie into CAN socket interfaces if possible
- figure out sane userspace api
This is definitely a no go! IMO there is no real alternative to make this cpc-usb driver a real CAN network driver.
The CAN driver interface has a sane configuration API via netlink and brings everything to configure CAN specific bitrates, error counters, recovery, etc.
The missing thing is to connect the usb-device to a netdevice (can%d), remove all the chardev file-I/O stuff and adapt the cpc-usb to use the bitrate-settings, error counters and whatever - which is already well-defined and provided by the CAN driver interface library contributed by Wolfgang Grandegger ( drivers/net/can/dev.c and include/linux/can/[dev.h|netlink.h] ).
Unfortunately i'm not an expert in USB programming and i don't have that hardware - but if you need some ideas from the CAN driver peoples like Wolfgang, questions are always welcome, e.g. on the socketcan-core ML:
http://developer.berlios.de/projects/socketcan
I don't think it's a big effort for people that know USB & CAN to clean up the cpc-usb and make it a slim CAN netdev. Believe me, it took years to figure out a sane userspace api for CAN interfaces, which is now provided by the netlink interface ;-)
Best regards,
Oliver
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Oliver,
I'm not yet sure how to actually start the development. There is so much to do, and I've not much time to spend on this, unfortunately. Because of this I can't rewrite the whole driver on my own in order to get a Socket-CAN driver but I can provide support, review patches, rent devices and make tests here.
Oliver, you are not familiar with USB and I'm not very familiar with CAN netdev internals, why not combining these twos. You are writing the CAN part and write the USB part.
I'll also write a specification which contains any information you need to develop a CAN driver for the device (commands, sequences, error handling).
- --
Mit freundlichen Gruessen/Best Regards,
Sebastian Haas
Software Entwicklung/Software Development
Phone: +49-9451-9432-22
Fax : +49-9451-9432-12
Email: [email protected]
Web : www.ems-wuensche.com
Quoted 53 lines · Oliver Hartkopp
Hello Greg and Sebastian,
i just looked around in the linux-next tree for the cpc-usb driver.
IMHO the sja2m16c* files are completely obsolete as the setting of the CAN bittimings needs to be done by separate functions (one for the SJA1000 and one for the M16C). For both of them a separate
can_bittiming_constis needed, like it is defined indrivers/net/can/sja1000/sja1000.c:static struct can_bittiming_const sja1000_bittiming_const = { .name = DRV_NAME, .tseg1_min = 1, .tseg1_max = 16, .tseg2_min = 1, .tseg2_max = 8, .sjw_max = 4, .brp_min = 1, .brp_max = 64, .brp_inc = 1, };Also a separate function to determine the register values from the calculated bittiming values is needed for both hardware types (SJA1000(LPC2119)/M16C) of the cpc-usb. How this is done can be checked in linux/drivers/net/can/* or in the source code of upcoming drivers in
http://svn.berlios.de/svnroot/repos/socketcan/trunk/kernel/2.6/drivers/net/can/
I wondered about the following items in the TODO list:
- tie into CAN socket interfaces if possible
- figure out sane userspace apiThis is definitely a no go! IMO there is no real alternative to make this cpc-usb driver a real CAN network driver.
The CAN driver interface has a sane configuration API via netlink and brings everything to configure CAN specific bitrates, error counters, recovery, etc.
The missing thing is to connect the usb-device to a netdevice (can%d), remove all the chardev file-I/O stuff and adapt the cpc-usb to use the bitrate-settings, error counters and whatever - which is already well-defined and provided by the CAN driver interface library contributed by Wolfgang Grandegger (
drivers/net/can/dev.cand include/linux/can/[dev.h|netlink.h] ).Unfortunately i'm not an expert in USB programming and i don't have that hardware - but if you need some ideas from the CAN driver peoples like Wolfgang, questions are always welcome, e.g. on the socketcan-core ML:
Quoted 7 lines
I don't think it's a big effort for people that know USB & CAN to clean up the cpc-usb and make it a slim CAN netdev. Believe me, it took years to figure out a sane userspace api for CAN interfaces, which is now provided by the netlink interface ;-)
Best regards,
Oliver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iEYEARECAAYFAkqkoJoACgkQpqRB8PJG7XxF/ACgjza8eG3U+ypyA0qCj60wDhmN 8oQAnir3YRmXU7CTlaKXpbecPyitJHqX
=hyD4
-----END PGP SIGNATURE-----
Signature · 7 lines
EMS Dr. Thomas Wuensche e.K. Sonnenhang 3 85304 Ilmmuenster HRA Neuburg a.d. Donau, HR-Nr. 70.106 Phone: +49-8441-490260 Fax : +49-8441-81860 http://www.ems-wuensche.com
Hi Sebastian,
Quoted 11 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Oliver,
I'm not yet sure how to actually start the development. There is so much to do, and I've not much time to spend on this, unfortunately. Because of this I can't rewrite the whole driver on my own in order to get a Socket-CAN driver but I can provide support, review patches, rent devices and make tests here.
Quoted 7 lines
Oliver, you are not familiar with USB and I'm not very familiar with CAN netdev internals, why not combining these twos. You are writing the CAN part and write the USB part.
I'll also write a specification which contains any information you need to develop a CAN driver for the device (commands, sequences, error handling).
Alternatively, EMS Wuensche could also hire an expert doing the job ;-). Note that we do a lot of Socket-CAN work in our free time, which is a limited resource. Progress depends on funding to a certain extend.
Wolfgang.
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Wolfgang,
Quoted 18 lines · Wolfgang Grandegger
Hi Sebastian,
Quoted 15 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Oliver,
I'm not yet sure how to actually start the development. There is so much to do, and I've not much time to spend on this, unfortunately. Because of this I can't rewrite the whole driver on my own in order to get a Socket-CAN driver but I can provide support, review patches, rent devices and make tests here.
Oliver, you are not familiar with USB and I'm not very familiar with CAN netdev internals, why not combining these twos. You are writing the CAN part and write the USB part.
Quoted 7 lines
Quoted 3 lines
I'll also write a specification which contains any information you need to develop a CAN driver for the device (commands, sequences, error handling).
Alternatively, EMS Wuensche could also hire an expert doing the job ;-). Note that we do a lot of Socket-CAN work in our free time, which is a limited resource. Progress depends on funding to a certain extend.
Money is also a limited resource. ;-)
Let's become serious again, I know and respect that many of Socket-CAN and the Staging developers spend their free time working on it. We will of course work on the driver, but since we've not much time it may take several months. If someone wants to help, we would be very glad and happy to support the person as far as we can with devices, answers and tests.
Sebastian
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iEYEARECAAYFAkqkveMACgkQpqRB8PJG7Xyu3ACeMhuOoVMQ043tib6HH9NhQPBw uTQAnjCFIqzv6dQl9iRiWopVYWAirdKb
=MRvL
-----END PGP SIGNATURE-----
Signature · 7 lines
EMS Dr. Thomas Wuensche e.K. Sonnenhang 3 85304 Ilmmuenster HRA Neuburg a.d. Donau, HR-Nr. 70.106 Phone: +49-8441-490260 Fax : +49-8441-81860 http://www.ems-wuensche.com
Quoted 31 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Wolfgang,
Quoted 18 lines · Wolfgang Grandegger
Hi Sebastian,
Quoted 15 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Oliver,
I'm not yet sure how to actually start the development. There is so much to do, and I've not much time to spend on this, unfortunately. Because of this I can't rewrite the whole driver on my own in order to get a Socket-CAN driver but I can provide support, review patches, rent devices and make tests here.
Oliver, you are not familiar with USB and I'm not very familiar with CAN netdev internals, why not combining these twos. You are writing the CAN part and write the USB part.
Quoted 7 lines
Quoted 3 lines
I'll also write a specification which contains any information you need to develop a CAN driver for the device (commands, sequences, error handling).
Alternatively, EMS Wuensche could also hire an expert doing the job ;-). Note that we do a lot of Socket-CAN work in our free time, which is a limited resource. Progress depends on funding to a certain extend.
Quoted 8 lines
Money is also a limited resource. ;-)
Let's become serious again, I know and respect that many of Socket-CAN and the Staging developers spend their free time working on it. We will of course work on the driver, but since we've not much time it may take several months. If someone wants to help, we would be very glad and happy to support the person as far as we can with devices, answers and tests.
OK, no problem. I really appreciate your support for Socket-CAN so far.
Thanks,
Wolfgang.
Quoted 36 lines · Wolfgang Grandegger
Quoted 35 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Wolfgang,
Quoted 20 lines · Wolfgang Grandegger
Hi Sebastian,
Quoted 17 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Oliver,
I'm not yet sure how to actually start the development. There is so much
to do, and I've not much time to spend on this, unfortunately. Because of this I can't rewrite the whole driver on my own in order to get a Socket-CAN driver but I can provide support, review patches, rent devices and make tests here.Oliver, you are not familiar with USB and I'm not very familiar with CAN
netdev internals, why not combining these twos. You are writing the CAN part and write the USB part.Quoted 7 lines
Quoted 3 lines
I'll also write a specification which contains any information you need to develop a CAN driver for the device (commands, sequences, error handling).
Alternatively, EMS Wuensche could also hire an expert doing the job ;-). Note that we do a lot of Socket-CAN work in our free time, which is a limited resource. Progress depends on funding to a certain extend.
Money is also a limited resource. ;-)
Quoted 8 lines
Quoted 6 lines
Let's become serious again, I know and respect that many of Socket-CAN and the Staging developers spend their free time working on it. We will of course work on the driver, but since we've not much time it may take several months. If someone wants to help, we would be very glad and happy to support the person as far as we can with devices, answers and tests.
OK, no problem. I really appreciate your support for Socket-CAN so far.
Indeed. Me too.
I tried to take a second look into cpc-usb_drv.c and i would suggest to remove all the procfs and the chardev stuff and then create a CAN netdev when you identified an USB node analogue to
/* Detect available channels */
for (i = 0; i < EMS_PCMCIA_MAX_CHAN; i++) {
dev = alloc_sja1000dev(0);
if (dev == NULL) {
err = -ENOMEM;
goto failure_cleanup;
}
card->net_dev[i] = dev;
priv = netdev_priv(dev);
priv->priv = card;
SET_NETDEV_DEV(dev, &pdev->dev);as you know from your ems_pcmcia.c driver
and
struct net_device *alloc_sja1000dev(int sizeof_priv)
{
struct net_device *dev;
struct sja1000_priv *priv;
dev = alloc_candev(sizeof(struct sja1000_priv) + sizeof_priv);
if (!dev)
return NULL;
priv = netdev_priv(dev);
priv->dev = dev;
priv->can.bittiming_const = &sja1000_bittiming_const;
priv->can.do_set_bittiming = sja1000_set_bittiming;
priv->can.do_set_mode = sja1000_set_mode;
if (sizeof_priv)
priv->priv = (void *)priv + sizeof(struct sja1000_priv);
return dev;
}as you know from the sja1000.c (which can probably be used for the LPC2119_PRODUCT_ID we should try to implement first).
Then we need something like this stuff
static const struct net_device_ops sja1000_netdev_ops = {
.ndo_open = sja1000_open,
.ndo_stop = sja1000_close,
.ndo_start_xmit = sja1000_start_xmit,};
int register_sja1000dev(struct net_device *dev)
{
if (!sja1000_probe_chip(dev))
return -ENODEV;
dev->netdev_ops = &sja1000_netdev_ops;
dev->flags |= IFF_ECHO; /* we support local echo */
set_reset_mode(dev);
chipset_init(dev);
return register_candev(dev);
}from sja1000.c
And then we have an USB CAN node that has a belonging CAN netdevice (maybe there is something else we can look at that's used in other USB ethernet adapters).
I know from the PEAK USB driver at
http://www.peak-system.com/fileadmin/media/linux/files/peak-linux-driver.6.11.tar.gz
that i just needed to duplicate and modify the usb rx/tx stuff and redirect the CAN frames into the network stack. But this PEAK driver does not have a netlink configuration interface and can only be taken as a limited example ...
I assume, when the driver (cpc_usb.c or ems_usb.c analogue to the ems_pcmcia.c ?) is prepared as described above, one can go and connect the rx/tx dataflow and the netlink configuration.
Unfortunately i'm short of time the next two weeks but maybe you can start and create such a new C-file (probably based on ems_pcmcia.c) ?
Best regards,
Oliver
Quoted 131 lines · Oliver Hartkopp
Quoted 36 lines · Wolfgang Grandegger
Quoted 35 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Wolfgang,
Quoted 20 lines · Wolfgang Grandegger
Hi Sebastian,
Quoted 17 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Oliver,
I'm not yet sure how to actually start the development. There is so much
to do, and I've not much time to spend on this, unfortunately. Because of this I can't rewrite the whole driver on my own in order to get a Socket-CAN driver but I can provide support, review patches, rent devices and make tests here.Oliver, you are not familiar with USB and I'm not very familiar with CAN
netdev internals, why not combining these twos. You are writing the CAN part and write the USB part.Quoted 7 lines
Quoted 3 lines
I'll also write a specification which contains any information you need to develop a CAN driver for the device (commands, sequences, error handling).
Alternatively, EMS Wuensche could also hire an expert doing the job ;-). Note that we do a lot of Socket-CAN work in our free time, which is a limited resource. Progress depends on funding to a certain extend.
Money is also a limited resource. ;-)
Quoted 8 lines
Quoted 6 lines
Let's become serious again, I know and respect that many of Socket-CAN and the Staging developers spend their free time working on it. We will of course work on the driver, but since we've not much time it may take several months. If someone wants to help, we would be very glad and happy to support the person as far as we can with devices, answers and tests.
OK, no problem. I really appreciate your support for Socket-CAN so far.
Indeed. Me too.
I tried to take a second look into
cpc-usb_drv.cand i would suggest to remove all the procfs and the chardev stuff and then create a CAN netdev when you identified an USB node analogue to/* Detect available channels */ for (i = 0; i< EMS_PCMCIA_MAX_CHAN; i++) { dev = alloc_sja1000dev(0); if (dev == NULL) { err = -ENOMEM; goto failure_cleanup; } card->net_dev[i] = dev; priv = netdev_priv(dev); priv->priv = card; SET_NETDEV_DEV(dev,&pdev->dev);as you know from your
ems_pcmcia.cdriverand
struct
net_device*alloc_sja1000dev(intsizeof_priv){ struct net_device *dev; struct sja1000_priv *priv; dev = alloc_candev(sizeof(struct sja1000_priv) + sizeof_priv); if (!dev) return NULL; priv = netdev_priv(dev); priv->dev = dev; priv->can.bittiming_const =&sja1000_bittiming_const; priv->can.do_set_bittiming = sja1000_set_bittiming; priv->can.do_set_mode = sja1000_set_mode; if (sizeof_priv) priv->priv = (void *)priv + sizeof(struct sja1000_priv); return dev; }as you know from the
sja1000.c(which can probably be used for theLPC2119_PRODUCT_IDwe should try to implement first).Then we need something like this stuff
static const struct
net_device_opssja1000_netdev_ops= {.ndo_open = sja1000_open, .ndo_stop = sja1000_close, .ndo_start_xmit = sja1000_start_xmit,};
int
register_sja1000dev(struct net_device *dev){ if (!sja1000_probe_chip(dev)) return -ENODEV; dev->netdev_ops =&sja1000_netdev_ops; dev->flags |= IFF_ECHO; /* we support local echo */ set_reset_mode(dev); chipset_init(dev); return register_candev(dev); }from
sja1000.cAnd then we have an USB CAN node that has a belonging CAN netdevice (maybe there is something else we can look at that's used in other USB ethernet adapters).
I know from the PEAK USB driver at
http://www.peak-system.com/fileadmin/media/linux/files/peak-linux-driver.6.11.tar.gz
that i just needed to duplicate and modify the usb rx/tx stuff and redirect the CAN frames into the network stack. But this PEAK driver does not have a netlink configuration interface and can only be taken as a limited example ...
Quoted 6 lines
I assume, when the driver (
cpc_usb.corems_usb.canalogue to theems_pcmcia.c?) is prepared as described above, one can go and connect the rx/tx dataflow and the netlink configuration.Unfortunately i'm short of time the next two weeks but maybe you can start and create such a new C-file (probably based on
ems_pcmcia.c) ?
Also, there are USB network driver in "drivers/net/usb/" which might serve as examples.
Wolfgang.
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Okay, thanks for the tips. Lets see what I can create today.
Sebastian
Quoted 133 lines · Oliver Hartkopp
Quoted 35 lines · Wolfgang Grandegger
Quoted 34 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Wolfgang,
Quoted 20 lines · Wolfgang Grandegger
Hi Sebastian,
Quoted 17 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Oliver,
I'm not yet sure how to actually start the development. There is so much
to do, and I've not much time to spend on this, unfortunately. Because of this I can't rewrite the whole driver on my own in order to get a Socket-CAN driver but I can provide support, review patches, rent devices and make tests here.Oliver, you are not familiar with USB and I'm not very familiar with CAN
netdev internals, why not combining these twos. You are writing the CAN part and write the USB part.Quoted 6 lines
Quoted 3 lines
I'll also write a specification which contains any information you need to develop a CAN driver for the device (commands, sequences, error handling).
Alternatively, EMS Wuensche could also hire an expert doing the job ;-). Note that we do a lot of Socket-CAN work in our free time, which is a limited resource. Progress depends on funding to a certain extend.
Money is also a limited resource. ;-)
Quoted 7 lines
Quoted 6 lines
Let's become serious again, I know and respect that many of Socket-CAN and the Staging developers spend their free time working on it. We will of course work on the driver, but since we've not much time it may take several months. If someone wants to help, we would be very glad and happy to support the person as far as we can with devices, answers and tests.
OK, no problem. I really appreciate your support for Socket-CAN so far.
Indeed. Me too.
I tried to take a second look into
cpc-usb_drv.cand i would suggest to remove all the procfs and the chardev stuff and then create a CAN netdev when you identified an USB node analogue to/* Detect available channels */ for (i = 0; i < EMS_PCMCIA_MAX_CHAN; i++) { dev = alloc_sja1000dev(0); if (dev == NULL) { err = -ENOMEM; goto failure_cleanup; } card->net_dev[i] = dev; priv = netdev_priv(dev); priv->priv = card; SET_NETDEV_DEV(dev, &pdev->dev);as you know from your
ems_pcmcia.cdriverand
struct
net_device*alloc_sja1000dev(intsizeof_priv){ struct net_device *dev; struct sja1000_priv *priv; dev = alloc_candev(sizeof(struct sja1000_priv) + sizeof_priv); if (!dev) return NULL; priv = netdev_priv(dev); priv->dev = dev; priv->can.bittiming_const = &sja1000_bittiming_const; priv->can.do_set_bittiming = sja1000_set_bittiming; priv->can.do_set_mode = sja1000_set_mode; if (sizeof_priv) priv->priv = (void *)priv + sizeof(struct sja1000_priv); return dev; }as you know from the
sja1000.c(which can probably be used for theLPC2119_PRODUCT_IDwe should try to implement first).Then we need something like this stuff
static const struct
net_device_opssja1000_netdev_ops= {.ndo_open = sja1000_open, .ndo_stop = sja1000_close, .ndo_start_xmit = sja1000_start_xmit,};
int
register_sja1000dev(struct net_device *dev){ if (!sja1000_probe_chip(dev)) return -ENODEV; dev->netdev_ops = &sja1000_netdev_ops; dev->flags |= IFF_ECHO; /* we support local echo */ set_reset_mode(dev); chipset_init(dev); return register_candev(dev); }from
sja1000.cAnd then we have an USB CAN node that has a belonging CAN netdevice (maybe there is something else we can look at that's used in other USB ethernet adapters).
I know from the PEAK USB driver at
http://www.peak-system.com/fileadmin/media/linux/files/peak-linux-driver.6.11.tar.gz
that i just needed to duplicate and modify the usb rx/tx stuff and redirect the CAN frames into the network stack. But this PEAK driver does not have a netlink configuration interface and can only be taken as a limited example ...
I assume, when the driver (
cpc_usb.corems_usb.canalogue to theems_pcmcia.c?) is prepared as described above, one can go and connect the rx/tx dataflow and the netlink configuration.
Quoted 5 lines
Unfortunately i'm short of time the next two weeks but maybe you can start and create such a new C-file (probably based on
ems_pcmcia.c) ?Best regards,
Oliver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iEYEARECAAYFAkqk6TcACgkQpqRB8PJG7XzpQACePuMXFX6pSg7EyssTNnDfVomv Lm0AnA7WKWLHfRny2iF5krEaT966WmPJ
=07pa
-----END PGP SIGNATURE-----
Signature · 7 lines
EMS Dr. Thomas Wuensche e.K. Sonnenhang 3 85304 Ilmmuenster HRA Neuburg a.d. Donau, HR-Nr. 70.106 Phone: +49-8441-490260 Fax : +49-8441-81860 http://www.ems-wuensche.com
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Oliver,
Okay, I've just finished the first version today. It is much less effort
as I previously thought. 95% is written and compiles fine. Just the
sending part is missing and optimization (it is just a basic implementation without USB anchors and stuff like that).
I think the further development should proceed at the Socket-CAN mailing list, cause of things needs to be clarified specific to the core.
Cheers,
Sebastian
Quoted 142 lines · Sebastian Haas
Okay, thanks for the tips. Lets see what I can create today.
Sebastian
Quoted 137 lines · Oliver Hartkopp
Quoted 35 lines · Wolfgang Grandegger
Quoted 34 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Wolfgang,
Quoted 20 lines · Wolfgang Grandegger
Hi Sebastian,
Quoted 17 lines · Sebastian Haas
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Oliver,
I'm not yet sure how to actually start the development. There is so much
to do, and I've not much time to spend on this, unfortunately. Because of this I can't rewrite the whole driver on my own in order to get a Socket-CAN driver but I can provide support, review patches, rent devices and make tests here.Oliver, you are not familiar with USB and I'm not very familiar with CAN
netdev internals, why not combining these twos. You are writing the CAN part and write the USB part.Quoted 6 lines
Quoted 3 lines
I'll also write a specification which contains any information you need to develop a CAN driver for the device (commands, sequences, error handling).
Alternatively, EMS Wuensche could also hire an expert doing the job ;-). Note that we do a lot of Socket-CAN work in our free time, which is a limited resource. Progress depends on funding to a certain extend.
Money is also a limited resource. ;-)
Quoted 7 lines
Quoted 6 lines
Let's become serious again, I know and respect that many of Socket-CAN and the Staging developers spend their free time working on it. We will of course work on the driver, but since we've not much time it may take several months. If someone wants to help, we would be very glad and happy to support the person as far as we can with devices, answers and tests.
OK, no problem. I really appreciate your support for Socket-CAN so far.
Indeed. Me too.
I tried to take a second look into
cpc-usb_drv.cand i would suggest to remove all the procfs and the chardev stuff and then create a CAN netdev when you identified an USB node analogue to/* Detect available channels */ for (i = 0; i < EMS_PCMCIA_MAX_CHAN; i++) { dev = alloc_sja1000dev(0); if (dev == NULL) { err = -ENOMEM; goto failure_cleanup; } card->net_dev[i] = dev; priv = netdev_priv(dev); priv->priv = card; SET_NETDEV_DEV(dev, &pdev->dev);as you know from your
ems_pcmcia.cdriverand
struct
net_device*alloc_sja1000dev(intsizeof_priv){ struct net_device *dev; struct sja1000_priv *priv; dev = alloc_candev(sizeof(struct sja1000_priv) + sizeof_priv); if (!dev) return NULL; priv = netdev_priv(dev); priv->dev = dev; priv->can.bittiming_const = &sja1000_bittiming_const; priv->can.do_set_bittiming = sja1000_set_bittiming; priv->can.do_set_mode = sja1000_set_mode; if (sizeof_priv) priv->priv = (void *)priv + sizeof(struct sja1000_priv); return dev; }as you know from the
sja1000.c(which can probably be used for theLPC2119_PRODUCT_IDwe should try to implement first).Then we need something like this stuff
static const struct
net_device_opssja1000_netdev_ops= {.ndo_open = sja1000_open, .ndo_stop = sja1000_close, .ndo_start_xmit = sja1000_start_xmit,};
int
register_sja1000dev(struct net_device *dev){ if (!sja1000_probe_chip(dev)) return -ENODEV; dev->netdev_ops = &sja1000_netdev_ops; dev->flags |= IFF_ECHO; /* we support local echo */ set_reset_mode(dev); chipset_init(dev); return register_candev(dev); }from
sja1000.cAnd then we have an USB CAN node that has a belonging CAN netdevice (maybe there is something else we can look at that's used in other USB ethernet adapters).
I know from the PEAK USB driver at
http://www.peak-system.com/fileadmin/media/linux/files/peak-linux-driver.6.11.tar.gz
that i just needed to duplicate and modify the usb rx/tx stuff and redirect the CAN frames into the network stack. But this PEAK driver does not have a netlink configuration interface and can only be taken as a limited example ...
I assume, when the driver (
cpc_usb.corems_usb.canalogue to theems_pcmcia.c?) is prepared as described above, one can go and connect the rx/tx dataflow and the netlink configuration.Unfortunately i'm short of time the next two weeks but maybe you can start and create such a new C-file (probably based on
ems_pcmcia.c) ?Best regards,
Oliver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
iEYEARECAAYFAkqlKDsACgkQpqRB8PJG7XwpdgCglYjvGi/z1z5tX1ozgF/YTA1j 9pwAnAkIHScIlic0KZNZEDWT09jUt3N1
=OVN3
-----END PGP SIGNATURE-----
Signature · 7 lines
EMS Dr. Thomas Wuensche e.K. Sonnenhang 3 85304 Ilmmuenster HRA Neuburg a.d. Donau, HR-Nr. 70.106 Phone: +49-8441-490260 Fax : +49-8441-81860 http://www.ems-wuensche.com
Quoted 2 lines · Sebastian Haas
Okay, I've just finished the first version today. It is much less effort
as I previously thought. 95% is written and compiles fine.
Great!
Quoted 6 lines
Just the
sending part is missing and optimization (it is just a basic implementation without USB anchors and stuff like that).I think the further development should proceed at the Socket-CAN mailing list, cause of things needs to be clarified specific to the core.
Yep! Good idea.
Many thanks,
Oliver