davinci_emac driver: modify to allow support for DA8xx
PATCH 1/1 davinci_emac driver: modify to allow support for DA8xx
Abstract out $ARCH specific parts of the davinci_emac driver.
Some Davinci devices contain an EMAC implemetation that has small differences from the devices currently supported by the driver. Abstrating those sections into static inlines in the $ARCH include files allows those parts to be modified per $ARCH.
Specifically this patch will allow DA830 and DA850 devices to use the same driver as many DMXXXX devices.
---
Applies to u-boot-ti
Only tested on DA830
drivers/net/davinci_emac.c | 61 ++++++++++++------------------ include/asm-arm/arch-davinci/emac_defs.h | 35 +++++++++++++++++ 2 files changed, 59 insertions(+), 37 deletions(-)
drivers/net/davinci_emac.c +24 -37
@@ -1,6 +1,10 @@/* * Ethernet driver for TI TMS320DM644x (DaVinci) chips. * +* Copyright (C) 2009 Nick Thompson, GE Fanuc Ltd <[email protected]> +* +* Abstracted out code not common to all davinci class devices. +* * Copyright (C) 2007 Sergey Kubushyn <[email protected]> * * Parts shamelessly stolen from TI's dm644x_emac.c. Original copyright
@@ -119,7 +123,8 @@ static int davinci_eth_phy_detect(void) active_phy_addr =0xff ; -if ((phy_act_state = adap_mdio->ALIVE) ==0 ) + phy_act_state = adap_mdio->ALIVE &EMAC_MDIO_PHY_MASK ; +if (phy_act_state ==0 )return (0 );/* No active PHYs */ debug_emac ("davinci_eth_phy_detect(), ALIVE = 0x%08x\n" , phy_act_state);
@@ -261,10 +266,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)/* Reset EMAC module and disable interrupts in wrapper */ adap_emac->SOFTRESET =1 ;while (adap_emac->SOFTRESET !=0 ) {;} - adap_ewrap->EWCTL =0 ; -for (cnt =0 ; cnt <5 ; cnt++) { - clkdiv = adap_ewrap->EWCTL; - } +davinci_reset_emac_wrapper (adap_ewrap); rx_desc = emac_rx_desc;
@@ -272,30 +274,11 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis) adap_emac->RXCONTROL =0x01 ;/* Set MAC Addresses & Init multicast Hash to 0 (disable any multicast receive) */ -/* Using channel 0 only - other channels are disabled */ - adap_emac->MACINDEX =0 ; - adap_emac->MACADDRHI = - (davinci_eth_mac_addr[3 ] <<24 ) | - (davinci_eth_mac_addr[2 ] <<16 ) | - (davinci_eth_mac_addr[1 ] <<8 ) | - (davinci_eth_mac_addr[0 ]); - adap_emac->MACADDRLO = - (davinci_eth_mac_addr[5 ] <<8 ) | - (davinci_eth_mac_addr[4 ]); +davinci_emac_set_mac_addr (adap_emac, davinci_eth_mac_addr); adap_emac->MACHASH1 =0 ; adap_emac->MACHASH2 =0 ; -/* Set source MAC address - REQUIRED */ - adap_emac->MACSRCADDRHI = - (davinci_eth_mac_addr[3 ] <<24 ) | - (davinci_eth_mac_addr[2 ] <<16 ) | - (davinci_eth_mac_addr[1 ] <<8 ) | - (davinci_eth_mac_addr[0 ]); - adap_emac->MACSRCADDRLO = - (davinci_eth_mac_addr[4 ] <<8 ) | - (davinci_eth_mac_addr[5 ]); -/* Set DMA 8 TX / 8 RX Head pointers to 0 */ addr = &adap_emac->TX0HDP;for (cnt =0 ; cnt <16 ; cnt++)
@@ -341,7 +324,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis) adap_emac->RXUNICASTSET =0x01 ;/* Enable MII interface and Full duplex mode */ - adap_emac->MACCONTROL = (EMAC_MACCONTROL_MIIEN_ENABLE |EMAC_MACCONTROL_FULLDUPLEX_ENABLE ); +davinci_enable_mii (adap_emac);/* Init MDIO & get link state */ clkdiv = (EMAC_MDIO_BUS_FREQ /EMAC_MDIO_CLOCK_FREQ ) -1 ;
@@ -374,9 +357,9 @@ static void davinci_eth_ch_teardown(int ch)* Note: A task delay can be called here to pend rather than * occupying CPU cycles - anyway it has been found that teardown * takes very few cpu cycles and does not affect functionality */ - dly--; -udelay (1 ); -if (dly ==0 ) + dly--; +udelay (1 ); +if (dly ==0 )break ; } adap_emac->TX0CP = cnt;
@@ -389,9 +372,9 @@ static void davinci_eth_ch_teardown(int ch)* Note: A task delay can be called here to pend rather than * occupying CPU cycles - anyway it has been found that teardown * takes very few cpu cycles and does not affect functionality */ - dly--; -udelay (1 ); -if (dly ==0 ) + dly--; +udelay (1 ); +if (dly ==0 )break ; } adap_emac->RX0CP = cnt;
@@ -411,7 +394,7 @@ static void davinci_eth_close(struct eth_device *dev)/* Reset EMAC module and disable interrupts in wrapper */ adap_emac->SOFTRESET =1 ; - adap_ewrap->EWCTL =0 ; +davinci_reset_emac_wrapper (adap_ewrap);debug_emac ("- emac_close\n" ); }
@@ -445,9 +428,9 @@ static int davinci_eth_send_packet (struct eth_device *dev, emac_tx_desc->buffer = (u_int8_t *) packet; emac_tx_desc->buff_off_len = (length &0xffff ); emac_tx_desc->pkt_flag_len = ((length &0xffff ) | -EMAC_CPPI_SOP_BIT | -EMAC_CPPI_OWNERSHIP_BIT | -EMAC_CPPI_EOP_BIT ); +EMAC_CPPI_SOP_BIT | +EMAC_CPPI_OWNERSHIP_BIT | +EMAC_CPPI_EOP_BIT );/* Send the packet */ adap_emac->TX0HDP = (unsigned int ) emac_tx_desc;
@@ -485,7 +468,7 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)printf ("WARN: emac_rcv_pkt: Error in packet\n" ); }else {NetReceive (rx_curr_desc->buffer, - (rx_curr_desc->buff_off_len &0xffff )); + (rx_curr_desc->buff_off_len &0xffff )); ret = rx_curr_desc->buff_off_len &0xffff ; }
@@ -596,6 +579,7 @@ int davinci_emac_initialize(void) phy_id |= tmp &0x0000ffff ;switch (phy_id) { +#ifdef PHY_LXT972 case PHY_LXT972 :sprintf (phy.name,"LXT972 @ 0x%02x" , active_phy_addr); phy.init = lxt972_init_phy;
@@ -603,6 +587,8 @@ int davinci_emac_initialize(void) phy.get_link_speed = lxt972_get_link_speed; phy.auto_negotiate = lxt972_auto_negotiate;break ; +#endif +#ifdef PHY_DP83848 case PHY_DP83848 :sprintf (phy.name,"DP83848 @ 0x%02x" , active_phy_addr); phy.init = dp83848_init_phy;
@@ -610,6 +596,7 @@ int davinci_emac_initialize(void) phy.get_link_speed = dp83848_get_link_speed; phy.auto_negotiate = dp83848_auto_negotiate;break ; +#endif default :sprintf (phy.name,"GENERIC @ 0x%02x" , active_phy_addr); phy.init = gen_init_phy;
include/asm-arm/arch-davinci/emac_defs.h +35 -0
@@ -338,4 +338,39 @@ int dp83848_get_link_speed(int phy_addr);int dp83848_init_phy (int phy_addr);int dp83848_auto_negotiate (int phy_addr); +static inline void davinci_emac_set_mac_addr (volatile emac_regs *adap_emac, +u_init8 *mac_addr) +{ +unsigned long mac_hi; +unsigned long mac_lo; + + mac_hi = (mac_addr[3 ] <<24 ) | (mac_addr[2 ] <<16 ) | + (mac_addr[1 ] <<8 ) | (mac_addr[0 ]); + mac_lo = (mac_addr[5 ] <<8 ) | (mac_addr[4 ]); + +/* Using channel 0 only - other channels are disabled */ + adap_emac->MACINDEX =0 ; + adap_emac->MACADDRHI = mac_hi; + adap_emac->MACADDRLO = mac_lo; + +/* Set source MAC address - REQUIRED */ + adap_emac->MACSRCADDRHI = mac_hi; + adap_emac->MACSRCADDRLO = mac_lo; +} + +static inline void davinci_enable_mii (volatile emac_regs *adap_emac) +{ + adap_emac->MACCONTROL = (EMAC_MACCONTROL_MIIEN_ENABLE | +EMAC_MACCONTROL_FULLDUPLEX_ENABLE ); +} + +static inline void davinci_reset_emac_wrapper (volatile ewrap_regs *adap_ewrap) +{ +u_int32_t dummy; + + adap_ewrap->EWCTL =0 ; +for (cnt =0 ; cnt <5 ; cnt++) + dummy = adap_ewrap->EWCTL; +} +#endif /* _DM644X_EMAC_H_ */
Paulraj
PATCH 1/1 davinci_emac driver: modify to allow support for DA8xx
Quoted 58 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Nick Thompson
Sent: Tuesday, October 20, 2009 9:21 AM
To: Ben Warren; u-boot at lists.denx.de
Subject: [U-Boot] [PATCH 1/1]davinci_emacdriver: modify to allow support for DA8xxAbstract out $ARCH specific parts of the
davinci_emacdriver.Some Davinci devices contain an EMAC implemetation that has small differences from the devices currently supported by the driver. Abstrating those sections into static inlines in the $ARCH include files allows those parts to be modified per $ARCH.
Specifically this patch will allow DA830 and DA850 devices to use the same driver as many DMXXXX devices.
Signed-off-by Nick Thompson <[email protected]>---
Applies to u-boot-ti
Only tested on DA830drivers/net/davinci_emac.c | 61 ++++++++++++------------- ----- include/asm-arm/arch-davinci/emac_defs.h | 35 +++++++++++++++++ 2 files changed, 59 insertions(+), 37 deletions(-)drivers/net/davinci_emac.c +1
-0@@ -1,6 +1,10 @@/* * Ethernet driver for TI TMS320DM644x (DaVinci) chips. * +* Copyright (C) 2009 Nick Thompson, GE Fanuc Ltd <[email protected]>
+ *
+ * Abstracted out code not common to all davinci class devices.
+ *
* Copyright (C) 2007 Sergey Kubushyn <[email protected]>
*
* Parts shamelessly stolen from TI'sdm644x_emac.c. Original copyrightdrivers/net/davinci_emac.c +2
-1@@ -119,7 +123,8 @@ static int davinci_eth_phy_detect(void) active_phy_addr =0xff ; -if ((phy_act_state = adap_mdio->ALIVE) ==0 ) + phy_act_state = adap_mdio->ALIVE &EMAC_MDIO_PHY_MASK ; +if (phy_act_state ==0 )return (0 );/* No active PHYs */ debug_emac("davinci_eth_phy_detect(), ALIVE = 0x%08x\n",
phy_act_state);
drivers/net/davinci_emac.c static int davinci_eth_open(struct eth_device *dev, · line 270
Quoted 9 lines
drivers/net/davinci_emac.c +1
-4@@ -261,10 +266,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)/* Reset EMAC module and disable interrupts in wrapper */ adap_emac->SOFTRESET = 1;while (adap_emac->SOFTRESET !=0 ) {;} - adap_ewrap->EWCTL =0 ; -for (cnt =0 ; cnt <5 ; cnt++) { - clkdiv = adap_ewrap->EWCTL; - } +davinci_reset_emac_wrapper (adap_ewrap);
Dm6467 and DM365 uses a different set of registers to do this. Some time back I had submitted a patch.
It will be better if we modify this driver only once to support all DaVinci SOCs.
I submiited a patch for DM365 and DM6467 some time back
http://www.mail-archive.com/u-boot at lists.denx.de/msg23031.html
Ben can you comment on the above, I don't think I received any comments from you.
Quoted 189 lines
drivers/net/davinci_emac.c +0
-0rx_desc = emac_rx_desc;@@ -272,30 +274,11 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis) adap_emac->RXCONTROL = 0x01;/* Set MAC Addresses & Init multicast Hash to 0 (disable any multicast receive) */
drivers/net/davinci_emac.c +2
-21-/* Using channel 0 only - other channels are disabled */ - adap_emac->MACINDEX =0 ; - adap_emac->MACADDRHI = - (davinci_eth_mac_addr[3 ] <<24 ) | - (davinci_eth_mac_addr[2 ] <<16 ) | - (davinci_eth_mac_addr[1 ] <<8 ) | - (davinci_eth_mac_addr[0 ]); - adap_emac->MACADDRLO = - (davinci_eth_mac_addr[5 ] <<8 ) | - (davinci_eth_mac_addr[4 ]); +davinci_emac_set_mac_addr (adap_emac, davinci_eth_mac_addr); adap_emac->MACHASH1 =0 ; adap_emac->MACHASH2 =0 ; -/* Set source MAC address - REQUIRED */ - adap_emac->MACSRCADDRHI = - (davinci_eth_mac_addr[3 ] <<24 ) | - (davinci_eth_mac_addr[2 ] <<16 ) | - (davinci_eth_mac_addr[1 ] <<8 ) | - (davinci_eth_mac_addr[0 ]); - adap_emac->MACSRCADDRLO = - (davinci_eth_mac_addr[4 ] <<8 ) | - (davinci_eth_mac_addr[5 ]); -/* Set DMA 8 TX / 8 RX Head pointers to 0 */ addr = &adap_emac->TX0HDP;for (cnt =0 ; cnt <16 ; cnt++)@@ -341,7 +324,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis) adap_emac->RXUNICASTSET = 0x01;/* Enable MII interface and Full duplex mode */ - adap_emac->MACCONTROL = (EMAC_MACCONTROL_MIIEN_ENABLE | EMAC_MACCONTROL_FULLDUPLEX_ENABLE); +davinci_enable_mii (adap_emac);drivers/net/davinci_emac.c +0
-0/* Init MDIO & get link state */ clkdiv = (EMAC_MDIO_BUS_FREQ /EMAC_MDIO_CLOCK_FREQ ) -1 ;@@ -374,9 +357,9 @@ static void davinci_eth_ch_teardown(int ch)* Note: A task delay can be called here to pend rather than
* occupying CPU cycles - anyway it has been found that
teardown
* takes very few cpu cycles and does not affect
functionality */drivers/net/davinci_emac.c +3
-3- dly--; -udelay (1 ); -if (dly ==0 ) + dly--; +udelay (1 ); +if (dly ==0 )break ; } adap_emac->TX0CP = cnt;@@ -389,9 +372,9 @@ static void davinci_eth_ch_teardown(int ch)* Note: A task delay can be called here to pend rather than
* occupying CPU cycles - anyway it has been found that
teardown
* takes very few cpu cycles and does not affect
functionality */drivers/net/davinci_emac.c +12
-8- dly--; -udelay (1 ); -if (dly ==0 ) + dly--; +udelay (1 ); +if (dly ==0 )break ; } adap_emac->RX0CP = cnt;@@ -411,7 +394,7 @@ static void davinci_eth_close(struct eth_device *dev)/* Reset EMAC module and disable interrupts in wrapper */ adap_emac->SOFTRESET =1 ; - adap_ewrap->EWCTL =0 ; +davinci_reset_emac_wrapper (adap_ewrap);debug_emac ("- emac_close\n" ); }@@ -445,9 +428,9 @@ static int davinci_eth_send_packet (struct eth_device *dev, emac_tx_desc->buffer = (u_int8_t *) packet; emac_tx_desc->buff_off_len = (length &0xffff ); emac_tx_desc->pkt_flag_len = ((length &0xffff ) | -EMAC_CPPI_SOP_BIT | -EMAC_CPPI_OWNERSHIP_BIT | -EMAC_CPPI_EOP_BIT ); +EMAC_CPPI_SOP_BIT | +EMAC_CPPI_OWNERSHIP_BIT | +EMAC_CPPI_EOP_BIT );/* Send the packet */ adap_emac->TX0HDP = (unsigned int ) emac_tx_desc;@@ -485,7 +468,7 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)printf ("WARN: emac_rcv_pkt: Error in packet\n" ); }else {NetReceive (rx_curr_desc->buffer, - (rx_curr_desc->buff_off_len &0xffff )); + (rx_curr_desc->buff_off_len &0xffff )); ret = rx_curr_desc->buff_off_len &0xffff ; }@@ -596,6 +579,7 @@ int davinci_emac_initialize(void) phy_id |= tmp &0x0000ffff ;switch (phy_id) { +#ifdef PHY_LXT972 case PHY_LXT972 :sprintf (phy.name,"LXT972 @ 0x%02x" , active_phy_addr); phy.init = lxt972_init_phy;@@ -603,6 +587,8 @@ int davinci_emac_initialize(void) phy.get_link_speed = lxt972_get_link_speed; phy.auto_negotiate = lxt972_auto_negotiate;break ; +#endif +#ifdef PHY_DP83848 case PHY_DP83848 :sprintf (phy.name,"DP83848 @ 0x%02x" , active_phy_addr); phy.init = dp83848_init_phy;@@ -610,6 +596,7 @@ int davinci_emac_initialize(void) phy.get_link_speed = dp83848_get_link_speed; phy.auto_negotiate = dp83848_auto_negotiate;break ; +#endif default :sprintf (phy.name,"GENERIC @ 0x%02x" , active_phy_addr); phy.init = gen_init_phy;include/asm- renamed from include/asm-arm/arch-davinci/emac_defs.h +0
-0
arm/arch-davinci/emac_defs.h
index 96bc80e..fc70a31 100644include/asm-arm/arch-davinci/emac_defs.h +27
-0@@ -338,4 +338,39 @@ int dp83848_get_link_speed(int phy_addr);int dp83848_init_phy (int phy_addr);int dp83848_auto_negotiate (int phy_addr); +static inline void davinci_emac_set_mac_addr (volatile emac_regs *adap_emac, +u_init8 *mac_addr) +{ +unsigned long mac_hi; +unsigned long mac_lo; + + mac_hi = (mac_addr[3 ] <<24 ) | (mac_addr[2 ] <<16 ) | + (mac_addr[1 ] <<8 ) | (mac_addr[0 ]); + mac_lo = (mac_addr[5 ] <<8 ) | (mac_addr[4 ]); + +/* Using channel 0 only - other channels are disabled */ + adap_emac->MACINDEX =0 ; + adap_emac->MACADDRHI = mac_hi; + adap_emac->MACADDRLO = mac_lo; + +/* Set source MAC address - REQUIRED */ + adap_emac->MACSRCADDRHI = mac_hi; + adap_emac->MACSRCADDRLO = mac_lo; +} + +static inline void davinci_enable_mii (volatile emac_regs *adap_emac) +{ + adap_emac->MACCONTROL = (EMAC_MACCONTROL_MIIEN_ENABLE | +EMAC_MACCONTROL_FULLDUPLEX_ENABLE ); +} + +static inline void davinci_reset_emac_wrapper(volatile ewrap_regs
*adap_ewrap)include/asm-arm/arch-davinci/emac_defs.h +8
-0+{ +u_int32_t dummy; + + adap_ewrap->EWCTL =0 ; +for (cnt =0 ; cnt <5 ; cnt++) + dummy = adap_ewrap->EWCTL; +} +#endif /* _DM644X_EMAC_H_ */ _______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH 1/1 davinci_emac driver: modify to allow support for DA8xx
Quoted 70 lines · Sandeep
Quoted 57 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de[mailto:s-paulraj at ti.com] On Behalf Of Nick Thompson
Sent: Tuesday, October 20, 2009 9:21 AM
To: Ben Warren; u-boot at lists.denx.de
Subject: [U-Boot] [PATCH 1/1]davinci_emacdriver: modify to allow support for DA8xxAbstract out $ARCH specific parts of the
davinci_emacdriver.Some Davinci devices contain an EMAC implemetation that has small differences from the devices currently supported by the driver. Abstrating those sections into static inlines in the $ARCH include files allows those parts to be modified per $ARCH.
Specifically this patch will allow DA830 and DA850 devices to use the same driver as many DMXXXX devices.
Signed-off-by Nick Thompson <[email protected]>---
Applies to u-boot-ti
Only tested on DA830drivers/net/davinci_emac.c | 61 ++++++++++++------------- ----- include/asm-arm/arch-davinci/emac_defs.h | 35 +++++++++++++++++ 2 files changed, 59 insertions(+), 37 deletions(-)drivers/net/davinci_emac.c +1
-0@@ -1,6 +1,10 @@/* * Ethernet driver for TI TMS320DM644x (DaVinci) chips. * +* Copyright (C) 2009 Nick Thompson, GE Fanuc Ltd <[email protected]>
+ *
+ * Abstracted out code not common to all davinci class devices.
+ *
* Copyright (C) 2007 Sergey Kubushyn <[email protected]>
*
* Parts shamelessly stolen from TI'sdm644x_emac.c. Original copyrightdrivers/net/davinci_emac.c +2
-1@@ -119,7 +123,8 @@ static int davinci_eth_phy_detect(void) active_phy_addr =0xff ; -if ((phy_act_state = adap_mdio->ALIVE) ==0 ) + phy_act_state = adap_mdio->ALIVE &EMAC_MDIO_PHY_MASK ; +if (phy_act_state ==0 )return (0 );/* No active PHYs */ debug_emac("davinci_eth_phy_detect(), ALIVE = 0x%08x\n",
phy_act_state);drivers/net/davinci_emac.c static int davinci_eth_open(struct eth_device *dev, · line 270
Quoted 9 lines
drivers/net/davinci_emac.c +1
-4@@ -261,10 +266,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis)/* Reset EMAC module and disable interrupts in wrapper */ adap_emac->SOFTRESET = 1;while (adap_emac->SOFTRESET !=0 ) {;} - adap_ewrap->EWCTL =0 ; -for (cnt =0 ; cnt <5 ; cnt++) { - clkdiv = adap_ewrap->EWCTL; - } +davinci_reset_emac_wrapper (adap_ewrap);Dm6467 and DM365 uses a different set of registers to do this. Some time back I had submitted a patch.
Quoted 7 lines
It will be better if we modify this driver only once to support all DaVinci SOCs.
I submiited a patch for DM365 and DM6467 some time back
http://www.mail-archive.com/u-boot at lists.denx.de/msg23031.html
Ben can you comment on the above, I don't think I received any comments from you.
I think the two changes are largely compatible. The main difference (ignoring the gigabit changes) is that I've used static inlines rather than #ifdef. As I understand it, this is the preferred method.
I think the Sandeep's changes could also be done with static inline "methods", which, in general, can derisk changes for one SoC from effecting another as the base code need not be changed.
The disadvantage is that you may not have a method hook in place to make the changes you need, without changing several files to add one in and supply all the other SoC specific methods. Well, that and the fact the code is now stored in several files, rather than one.
I'm happy to go either way (inlines or ifdef's), if someone wants to make a call on what is most acceptable (for u-boot).
Quoted 189 lines
Quoted 188 lines
drivers/net/davinci_emac.c +0
-0rx_desc = emac_rx_desc;@@ -272,30 +274,11 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis) adap_emac->RXCONTROL = 0x01;/* Set MAC Addresses & Init multicast Hash to 0 (disable any multicast receive) */
drivers/net/davinci_emac.c +2
-21-/* Using channel 0 only - other channels are disabled */ - adap_emac->MACINDEX =0 ; - adap_emac->MACADDRHI = - (davinci_eth_mac_addr[3 ] <<24 ) | - (davinci_eth_mac_addr[2 ] <<16 ) | - (davinci_eth_mac_addr[1 ] <<8 ) | - (davinci_eth_mac_addr[0 ]); - adap_emac->MACADDRLO = - (davinci_eth_mac_addr[5 ] <<8 ) | - (davinci_eth_mac_addr[4 ]); +davinci_emac_set_mac_addr (adap_emac, davinci_eth_mac_addr); adap_emac->MACHASH1 =0 ; adap_emac->MACHASH2 =0 ; -/* Set source MAC address - REQUIRED */ - adap_emac->MACSRCADDRHI = - (davinci_eth_mac_addr[3 ] <<24 ) | - (davinci_eth_mac_addr[2 ] <<16 ) | - (davinci_eth_mac_addr[1 ] <<8 ) | - (davinci_eth_mac_addr[0 ]); - adap_emac->MACSRCADDRLO = - (davinci_eth_mac_addr[4 ] <<8 ) | - (davinci_eth_mac_addr[5 ]); -/* Set DMA 8 TX / 8 RX Head pointers to 0 */ addr = &adap_emac->TX0HDP;for (cnt =0 ; cnt <16 ; cnt++)@@ -341,7 +324,7 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis) adap_emac->RXUNICASTSET = 0x01;/* Enable MII interface and Full duplex mode */ - adap_emac->MACCONTROL = (EMAC_MACCONTROL_MIIEN_ENABLE | EMAC_MACCONTROL_FULLDUPLEX_ENABLE); +davinci_enable_mii (adap_emac);drivers/net/davinci_emac.c +0
-0/* Init MDIO & get link state */ clkdiv = (EMAC_MDIO_BUS_FREQ /EMAC_MDIO_CLOCK_FREQ ) -1 ;@@ -374,9 +357,9 @@ static void davinci_eth_ch_teardown(int ch)* Note: A task delay can be called here to pend rather than
* occupying CPU cycles - anyway it has been found that
teardown
* takes very few cpu cycles and does not affect
functionality */drivers/net/davinci_emac.c +3
-3- dly--; -udelay (1 ); -if (dly ==0 ) + dly--; +udelay (1 ); +if (dly ==0 )break ; } adap_emac->TX0CP = cnt;@@ -389,9 +372,9 @@ static void davinci_eth_ch_teardown(int ch)* Note: A task delay can be called here to pend rather than
* occupying CPU cycles - anyway it has been found that
teardown
* takes very few cpu cycles and does not affect
functionality */drivers/net/davinci_emac.c +12
-8- dly--; -udelay (1 ); -if (dly ==0 ) + dly--; +udelay (1 ); +if (dly ==0 )break ; } adap_emac->RX0CP = cnt;@@ -411,7 +394,7 @@ static void davinci_eth_close(struct eth_device *dev)/* Reset EMAC module and disable interrupts in wrapper */ adap_emac->SOFTRESET =1 ; - adap_ewrap->EWCTL =0 ; +davinci_reset_emac_wrapper (adap_ewrap);debug_emac ("- emac_close\n" ); }@@ -445,9 +428,9 @@ static int davinci_eth_send_packet (struct eth_device *dev, emac_tx_desc->buffer = (u_int8_t *) packet; emac_tx_desc->buff_off_len = (length &0xffff ); emac_tx_desc->pkt_flag_len = ((length &0xffff ) | -EMAC_CPPI_SOP_BIT | -EMAC_CPPI_OWNERSHIP_BIT | -EMAC_CPPI_EOP_BIT ); +EMAC_CPPI_SOP_BIT | +EMAC_CPPI_OWNERSHIP_BIT | +EMAC_CPPI_EOP_BIT );/* Send the packet */ adap_emac->TX0HDP = (unsigned int ) emac_tx_desc;@@ -485,7 +468,7 @@ static int davinci_eth_rcv_packet (struct eth_device *dev)printf ("WARN: emac_rcv_pkt: Error in packet\n" ); }else {NetReceive (rx_curr_desc->buffer, - (rx_curr_desc->buff_off_len &0xffff )); + (rx_curr_desc->buff_off_len &0xffff )); ret = rx_curr_desc->buff_off_len &0xffff ; }@@ -596,6 +579,7 @@ int davinci_emac_initialize(void) phy_id |= tmp &0x0000ffff ;switch (phy_id) { +#ifdef PHY_LXT972 case PHY_LXT972 :sprintf (phy.name,"LXT972 @ 0x%02x" , active_phy_addr); phy.init = lxt972_init_phy;@@ -603,6 +587,8 @@ int davinci_emac_initialize(void) phy.get_link_speed = lxt972_get_link_speed; phy.auto_negotiate = lxt972_auto_negotiate;break ; +#endif +#ifdef PHY_DP83848 case PHY_DP83848 :sprintf (phy.name,"DP83848 @ 0x%02x" , active_phy_addr); phy.init = dp83848_init_phy;@@ -610,6 +596,7 @@ int davinci_emac_initialize(void) phy.get_link_speed = dp83848_get_link_speed; phy.auto_negotiate = dp83848_auto_negotiate;break ; +#endif default :sprintf (phy.name,"GENERIC @ 0x%02x" , active_phy_addr); phy.init = gen_init_phy;include/asm- renamed from include/asm-arm/arch-davinci/emac_defs.h +0
-0
arm/arch-davinci/emac_defs.h
index 96bc80e..fc70a31 100644include/asm-arm/arch-davinci/emac_defs.h +27
-0@@ -338,4 +338,39 @@ int dp83848_get_link_speed(int phy_addr);int dp83848_init_phy (int phy_addr);int dp83848_auto_negotiate (int phy_addr); +static inline void davinci_emac_set_mac_addr (volatile emac_regs *adap_emac, +u_init8 *mac_addr) +{ +unsigned long mac_hi; +unsigned long mac_lo; + + mac_hi = (mac_addr[3 ] <<24 ) | (mac_addr[2 ] <<16 ) | + (mac_addr[1 ] <<8 ) | (mac_addr[0 ]); + mac_lo = (mac_addr[5 ] <<8 ) | (mac_addr[4 ]); + +/* Using channel 0 only - other channels are disabled */ + adap_emac->MACINDEX =0 ; + adap_emac->MACADDRHI = mac_hi; + adap_emac->MACADDRLO = mac_lo; + +/* Set source MAC address - REQUIRED */ + adap_emac->MACSRCADDRHI = mac_hi; + adap_emac->MACSRCADDRLO = mac_lo; +} + +static inline void davinci_enable_mii (volatile emac_regs *adap_emac) +{ + adap_emac->MACCONTROL = (EMAC_MACCONTROL_MIIEN_ENABLE | +EMAC_MACCONTROL_FULLDUPLEX_ENABLE ); +} + +static inline void davinci_reset_emac_wrapper(volatile ewrap_regs
*adap_ewrap)include/asm-arm/arch-davinci/emac_defs.h +8
-0+{ +u_int32_t dummy; + + adap_ewrap->EWCTL =0 ; +for (cnt =0 ; cnt <5 ; cnt++) + dummy = adap_ewrap->EWCTL; +} +#endif /* _DM644X_EMAC_H_ */ _______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot