Leadtek DTV-1000S
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 11 lines · Ryan Day
Michael-
I wanted to see if you might be able to assist in getting a DTV-1000S to work. I followed the instructions on the Whirlpool forum (DL the firmware, cp it to/lib/firmware, dl the dtv-1000s files from kernellabs.com, untar, make, make install, reboot), and everything looks good when I install, but when I reboot, the boot up hangs and eventually freezes.I thought reinstalling might give me a better chance for success with a clean slate to work with, but the problem continues. Unfortunately, I don't have any of the error logs or anything, as I reinstalled.
Quoted 8 lines
I can't remember the message at the first hang, but the freeze is caused by a failure to load the LIRC module.
Also of note is that I'm installing this card as a second tuner. I have a DTV-2000H already installed. I don't know if that changes anything.
Sorry I can't provide better info, but any advice you can give would be great.
Ryan,
This is really a question for the linux-media mailing list, so I've added it in cc -- please use REPLY-TO-ALL in your correspondence, so that anybody else that may have seen this issue can chime in with their advice, or perhaps they may benefit themselves simply by reading your problem description. Also, please remember that your response on the mailing list should appear below the quoted thread.
Meanwhile, why would failure to load the LIRC module cause a problem on your board, causing a system hang... Sounds fishy to me -- are you sure about this?
Have you tried deleting / blacklisting the module that you believe to be freezing your system?
Have you tried moving your PCI card to another slot?
Have you google'd for other users of your motherboard who might be suffering from similar issues?
I updated the dtv1000s tree yesterday, with the intention of getting it merged into the master branch. Perhaps there is a bug in the new repository that is not present in the old repository?
The current repository that you probably have already tested is located here:
http://kernellabs.com/hg/~mkrufky/dtv1000s
The only difference in the new tree when compared to the older tree, is that I've pulled in the latest v4l-dvb core changes from the master branch on linuxtv.org, and updated the DTV1000S patch to account for the latest board additions in the saa7134 driver. The dtv1000s support itself hasn't changed at all. To eliminate this as a possible cause, you can try testing the older tree, instead. The older tree that has already been tested by other users of both flavors of this dtv1000s board is located here:
http://kernellabs.com/hg/~mkrufky/dtv1000s.old
If the older repository works but the new one doesn't, that would indicate that there is a problem in the master v4l-dvb repository.
If all else fails, try removing the other board that you have installed, and see if that is a factor in this problem
Please test and report your findings back to the mailing list as a reply-to-all response in this thread.
I hope this helps.
Regards,
Mike Krufky
Hi Mike, Mauro,
Am Mittwoch, den 21.10.2009, 15:33 -0400 schrieb Michael Krufky:
Quoted 42 lines · Ryan Day
Quoted 11 lines
Michael-
I wanted to see if you might be able to assist in getting a DTV-1000S to work. I followed the instructions on the Whirlpool forum (DL the firmware, cp it to/lib/firmware, dl the dtv-1000s files from kernellabs.com, untar, make, make install, reboot), and everything looks good when I install, but when I reboot, the boot up hangs and eventually freezes.I thought reinstalling might give me a better chance for success with a clean slate to work with, but the problem continues. Unfortunately, I don't have any of the error logs or anything, as I reinstalled.
Quoted 8 lines
I can't remember the message at the first hang, but the freeze is caused by a failure to load the LIRC module.
Also of note is that I'm installing this card as a second tuner. I have a DTV-2000H already installed. I don't know if that changes anything.
Sorry I can't provide better info, but any advice you can give would be great.
Ryan,
This is really a question for the linux-media mailing list, so I've added it in cc -- please use REPLY-TO-ALL in your correspondence, so that anybody else that may have seen this issue can chime in with their advice, or perhaps they may benefit themselves simply by reading your problem description. Also, please remember that your response on the mailing list should appear below the quoted thread.
Meanwhile, why would failure to load the LIRC module cause a problem on your board, causing a system hang... Sounds fishy to me -- are you sure about this?
Have you tried deleting / blacklisting the module that you believe to be freezing your system?
Have you tried moving your PCI card to another slot?
Have you google'd for other users of your motherboard who might be suffering from similar issues?
Quoted 7 lines
I updated the dtv1000s tree yesterday, with the intention of getting it merged into the master branch. Perhaps there is a bug in the new repository that is not present in the old repository?
The current repository that you probably have already tested is located here:
there is another report for problems with the DTV-1000S now.
Checking the above and the master tree, it turns out that the card's analog entry made it into the #if 0 flyvideo tweaks in saa7134-cards.c and is not valid there.
Have to leave the house now, Mike please fix it or I'll send a fix when back later in the evening.
Cheers,
Hermann
Quoted 26 lines
The only difference in the new tree when compared to the older tree, is that I've pulled in the latest v4l-dvb core changes from the master branch on linuxtv.org, and updated the DTV1000S patch to account for the latest board additions in the saa7134 driver. The dtv1000s support itself hasn't changed at all. To eliminate this as a possible cause, you can try testing the older tree, instead. The older tree that has already been tested by other users of both flavors of this dtv1000s board is located here:
http://kernellabs.com/hg/~mkrufky/dtv1000s.old
If the older repository works but the new one doesn't, that would indicate that there is a problem in the master v4l-dvb repository.
If all else fails, try removing the other board that you have installed, and see if that is a factor in this problem
Please test and report your findings back to the mailing list as a reply-to-all response in this thread.
I hope this helps.
Regards,
Mike Krufky
Quoted 31 lines · hermann pitton
Hi Mike, Mauro,
Am Mittwoch, den 21.10.2009, 15:33 -0400 schrieb Michael Krufky:
Quoted 12 lines · Ryan Day
Quoted 11 lines
Michael-
I wanted to see if you might be able to assist in getting a DTV-1000S to work. I followed the instructions on the Whirlpool forum (DL the firmware, cp it to/lib/firmware, dl the dtv-1000s files from kernellabs.com, untar, make, make install, reboot), and everything looks good when I install, but when I reboot, the boot up hangs and eventually freezes.I thought reinstalling might give me a better chance for success with a clean slate to work with, but the problem continues. Unfortunately, I don't have any of the error logs or anything, as I reinstalled.
Quoted 9 lines
Quoted 8 lines
I can't remember the message at the first hang, but the freeze is caused by a failure to load the LIRC module.
Also of note is that I'm installing this card as a second tuner. I have a DTV-2000H already installed. I don't know if that changes anything.
Sorry I can't provide better info, but any advice you can give would be great.
there is another report for problems with the DTV-1000S now.
Checking the above and the master tree, it turns out that the card's analog entry made it into the #if 0 flyvideo tweaks in
saa7134-cards.cand is not valid there.
Quoted 6 lines
Have to leave the house now, Mike please fix it or I'll send a fix when back later in the evening.
Cheers,
Hermann
Thanks for spotting this, Hermann ... I just fixed the problem and pushed it to my DTV1000S tree. I'll issue a pull request to Mauro right now.
Cheers,
Mike
Hi,
Thanks for fixing this, I can confirm that it now compiles and
inserts and the remote works, so does the av input to the tvcard however the card does not seem to be able to tune any channels, I have checked the old driver and that is still able to tune in channels. The output from my dmesg is below.
Thanks
Michael Obst
[ 502.761860] saa7130/34: v4l2 driver version 0.2.15 loaded [ 502.761886] saa7130[0]: found at 0000:04:01.0, rev: 1, irq: 17, latency: 64, mmio: 0xfebffc00 [ 502.761890] saa7130[0]: subsystem: 107d:6655, board: Leadtek Winfast DTV1000S [card=175,autodetected] [ 502.761898] saa7130[0]: board init: gpio is 2121400 [ 502.761938] input: saa7134 IR (Leadtek Winfast DTV as /devices/pci0000:00/0000:00:1e.0/0000:04:01.0/input/input10 [ 502.761966] IRQ 17/saa7130[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 502.912003] saa7130[0]: i2c eeprom 00: 7d 10 55 66 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 [ 502.912009] saa7130[0]: i2c eeprom 10: 00 ff 82 0e ff 20 ff ff ff ff ff ff ff ff ff ff [ 502.912014] saa7130[0]: i2c eeprom 20: 01 40 01 01 01 ff 01 03 08 ff 00 8a ff ff ff ff [ 502.912019] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912024] saa7130[0]: i2c eeprom 40: ff 35 00 c0 00 10 03 02 ff 04 ff ff ff ff ff ff [ 502.912029] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912034] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912040] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912045] saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912050] saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912055] saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912060] saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912065] saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912070] saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912075] saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.912080] saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 502.928502] Chip ID is not zero. It is not a TEA5767 [ 502.928544] tuner 0-0060: chip found @ 0xc0 (saa7130[0]) [ 502.960501] tda8290: no gate control were provided! [ 502.960589] saa7130[0]: registered device video0 [v4l2] [ 502.960602] saa7130[0]: registered device vbi0 [ 502.963002] saa7134 ALSA driver for DMA sound loaded [ 502.963003] saa7130[0]/alsa: Leadtek Winfast DTV1000S doesn't support digital audio [ 502.963600] dvb_init() allocating 1 frontend [ 503.032771] tda18271 0-0060: creating new instance [ 503.040502] TDA18271HD/C2 detected @ 0-0060 [ 503.436003] DVB: registering new adapter (saa7130[0]) [ 503.436006] DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)... [ 503.764502] tda10048_firmware_upload: waiting for firmware upload (dvb-fe-tda10048-1.0.fw)... [ 503.764506] saa7134 0000:04:01.0: firmware: requesting dvb-fe-tda10048-1.0.fw [ 503.766223] tda10048_firmware_upload: firmware read 24878 bytes. [ 503.766224] tda10048_firmware_upload: firmware uploading [ 507.844010] tda10048_firmware_upload: firmware uploaded
2009/11/1 Michael Krufky <[email protected]>:
Quoted 52 lines
Quoted 31 lines · hermann pitton
Hi Mike, Mauro,
Am Mittwoch, den 21.10.2009, 15:33 -0400 schrieb Michael Krufky:
Quoted 12 lines · Ryan Day
Quoted 11 lines
Michael-
I wanted to see if you might be able to assist in getting a DTV-1000S to work. I followed the instructions on the Whirlpool forum (DL the firmware, cp it to/lib/firmware, dl the dtv-1000s files from kernellabs.com, untar, make, make install, reboot), and everything looks good when I install, but when I reboot, the boot up hangs and eventually freezes.I thought reinstalling might give me a better chance for success with a clean slate to work with, but the problem continues. Unfortunately, I don't have any of the error logs or anything, as I reinstalled.
Quoted 9 lines
Quoted 8 lines
I can't remember the message at the first hang, but the freeze is caused by a failure to load the LIRC module.
Also of note is that I'm installing this card as a second tuner. I have a DTV-2000H already installed. I don't know if that changes anything.
Sorry I can't provide better info, but any advice you can give would be great.
there is another report for problems with the DTV-1000S now.
Checking the above and the master tree, it turns out that the card's analog entry made it into the #if 0 flyvideo tweaks in
saa7134-cards.cand is not valid there.Quoted 6 lines
Have to leave the house now, Mike please fix it or I'll send a fix when back later in the evening.
Cheers,
HermannThanks for spotting this, Hermann ... I just fixed the problem and pushed it to my DTV1000S tree. I'll issue a pull request to Mauro right now.
Cheers,
Mike
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 9 lines · Michael Obst
Hi,
Thanks for fixing this, I can confirm that it now compiles and inserts and the remote works, so does the av input to the tvcard however the card does not seem to be able to tune any channels, I have checked the old driver and that is still able to tune in channels. The output from my dmesg is below.Thanks
Michael Obst
Michael,
This is an interesting problem -- the part of your dmesg that stands out to me is this:
Quoted 2 lines
[ 502.928544] tuner 0-0060: chip found @
0xc0(saa7130[0]) [ 502.960501] tda8290: no gate control were provided!
That error message was added as a safety measure -- it shouldn't be possible to ever hit that code path. Are you running any non-GPL binary drivers on your system, such as NVIDIA or anything else?
Let me explain:
The "no gate control were provided!" message was added by Mauro to the tda8290 driver, mainly as a check to ensure that we don't call a null function pointer. The gate control is actually provided by the tda8290 driver itself, by either tda8290_i2c_bridge or tda8295_i2c_bridge, depending on which hardware is present. In your case, it's a tda8290.
The function pointer is filled during the tda829x_attach() function, before we call the tda829x_find_tuner function, where this error message is displayed. The only way for this to have occurred, as far as I can tell, is if the probe to detect the tda8290 itself had failed.
Have you repeated your test with the same problem each time, or did this only happen once?
Can you try again, from a cold reboot?
Also, I'm just assuming that this failure occurred during a digital tune -- is that correct? Does analog television work?
If the problem is reproducible, can you also show us dmesg during a failed tune?
I'm very interested in hearing more about this -- please let me know.
Regards,
Mike
Quoted 42 lines · Michael Krufky
Quoted 9 lines · Michael Obst
Hi,
Thanks for fixing this, I can confirm that it now compiles and inserts and the remote works, so does the av input to the tvcard however the card does not seem to be able to tune any channels, I have checked the old driver and that is still able to tune in channels. The output from my dmesg is below.Thanks
Michael ObstMichael,
This is an interesting problem -- the part of your dmesg that stands out to me is this:
Quoted 2 lines
[ 502.928544] tuner 0-0060: chip found @
0xc0(saa7130[0]) [ 502.960501] tda8290: no gate control were provided!That error message was added as a safety measure -- it shouldn't be possible to ever hit that code path. Are you running any non-GPL binary drivers on your system, such as NVIDIA or anything else?
Let me explain:
The "no gate control were provided!" message was added by Mauro to the tda8290 driver, mainly as a check to ensure that we don't call a null function pointer. The gate control is actually provided by the tda8290 driver itself, by either
tda8290_i2c_bridgeortda8295_i2c_bridge, depending on which hardware is present. In your case, it's a tda8290.The function pointer is filled during the
tda829x_attach()function, before we call thetda829x_find_tunerfunction, where this error message is displayed. The only way for this to have occurred, as far as I can tell, is if the probe to detect the tda8290 itself had failed.Have you repeated your test with the same problem each time, or did this only happen once?
Quoted 8 lines
Can you try again, from a cold reboot?
Also, I'm just assuming that this failure occurred during a digital tune -- is that correct? Does analog television work?
If the problem is reproducible, can you also show us dmesg during a failed tune?
I'm very interested in hearing more about this -- please let me know.
Oops, on second look, seems that the error occurred during analog bring-up ... does digital tv work?
-Mike
This problem is reproducible and occurs the same from a cold boot or inserting saa7134. Analog tv has never worked on this card, I was under the impression there was no analog tuner on the card (looking at
http://www.leadtek.com/eng/tv_tuner/image/digital_tv.pdf). The info was simply from doing a modprobe on saa7134. The only lines in the dmesg that were different from the old driver was
saa7130[0]/alsa: Leadtek Winfast DTV1000S doesn't support digital audio
So I guess the analog part has always failed
I am using the nvidia driver and a driver for my wireless card, I will turn these off and see if I can get a different result.
During tuning for digital tv with the old driver I got
[ 1081.808505] tda18271: performing RF tracking filter calibration [ 1086.152006] tda18271: RF tracking filter calibration complete [ 1091.020535] hda-intel: IRQ timing workaround is activated for card
#0. Suggest a bigger bdl_pos_adj.
The final line did not appear when I tried to tune using the new version
[ 1225.904503] tda18271: performing RF tracking filter calibration [ 1230.272003] tda18271: RF tracking filter calibration complete
Thanks
Michael Obst
2009/11/1 Michael Krufky <[email protected]>:
Quoted 61 lines · Michael Krufky
Quoted 42 lines
Quoted 9 lines · Michael Obst
Hi,
Thanks for fixing this, I can confirm that it now compiles and inserts and the remote works, so does the av input to the tvcard however the card does not seem to be able to tune any channels, I have checked the old driver and that is still able to tune in channels. The output from my dmesg is below.Thanks
Michael ObstMichael,
This is an interesting problem -- the part of your dmesg that stands out to me is this:
Quoted 2 lines
[ 502.928544] tuner 0-0060: chip found @
0xc0(saa7130[0]) [ 502.960501] tda8290: no gate control were provided!That error message was added as a safety measure -- it shouldn't be possible to ever hit that code path. Are you running any non-GPL binary drivers on your system, such as NVIDIA or anything else?
Let me explain:
The "no gate control were provided!" message was added by Mauro to the tda8290 driver, mainly as a check to ensure that we don't call a null function pointer. The gate control is actually provided by the tda8290 driver itself, by either
tda8290_i2c_bridgeortda8295_i2c_bridge, depending on which hardware is present. In your case, it's a tda8290.The function pointer is filled during the
tda829x_attach()function, before we call thetda829x_find_tunerfunction, where this error message is displayed. The only way for this to have occurred, as far as I can tell, is if the probe to detect the tda8290 itself had failed.Have you repeated your test with the same problem each time, or did this only happen once?
Quoted 8 lines
Can you try again, from a cold reboot?
Also, I'm just assuming that this failure occurred during a digital tune -- is that correct? Does analog television work?
If the problem is reproducible, can you also show us dmesg during a failed tune?
I'm very interested in hearing more about this -- please let me know.
Oops, on second look, seems that the error occurred during analog bring-up ... does digital tv work?
-Mike
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 63 lines
2009/11/1 Michael Krufky <[email protected]>:
Quoted 61 lines · Michael Krufky
Quoted 42 lines
Quoted 9 lines · Michael Obst
Hi,
Thanks for fixing this, I can confirm that it now compiles and inserts and the remote works, so does the av input to the tvcard however the card does not seem to be able to tune any channels, I have checked the old driver and that is still able to tune in channels. The output from my dmesg is below.Thanks
Michael ObstMichael,
This is an interesting problem -- the part of your dmesg that stands out to me is this:
Quoted 2 lines
[ 502.928544] tuner 0-0060: chip found @
0xc0(saa7130[0]) [ 502.960501] tda8290: no gate control were provided!That error message was added as a safety measure -- it shouldn't be possible to ever hit that code path. Are you running any non-GPL binary drivers on your system, such as NVIDIA or anything else?
Let me explain:
The "no gate control were provided!" message was added by Mauro to the tda8290 driver, mainly as a check to ensure that we don't call a null function pointer. The gate control is actually provided by the tda8290 driver itself, by either
tda8290_i2c_bridgeortda8295_i2c_bridge, depending on which hardware is present. In your case, it's a tda8290.The function pointer is filled during the
tda829x_attach()function, before we call thetda829x_find_tunerfunction, where this error message is displayed. The only way for this to have occurred, as far as I can tell, is if the probe to detect the tda8290 itself had failed.Have you repeated your test with the same problem each time, or did this only happen once?
Quoted 8 lines
Can you try again, from a cold reboot?
Also, I'm just assuming that this failure occurred during a digital tune -- is that correct? Does analog television work?
If the problem is reproducible, can you also show us dmesg during a failed tune?
I'm very interested in hearing more about this -- please let me know.
Oops, on second look, seems that the error occurred during analog bring-up ... does digital tv work?
-Mike
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 19 lines · Michael Obst
This problem is reproducible and occurs the same from a cold boot or inserting saa7134. Analog tv has never worked on this card, I was under the impression there was no analog tuner on the card (looking at
http://www.leadtek.com/eng/tv_tuner/image/digital_tv.pdf). The info was simply from doing a modprobe on saa7134. The only lines in the dmesg that were different from the old driver wassaa7130[0]/alsa: Leadtek Winfast DTV1000S doesn't support digital audio
So I guess the analog part has always failed
I am using the nvidia driver and a driver for my wireless card, I will turn these off and see if I can get a different result.
During tuning for digital tv with the old driver I got
[ 1081.808505] tda18271: performing RF tracking filter calibration [ 1086.152006] tda18271: RF tracking filter calibration complete [ 1091.020535] hda-intel: IRQ timing workaround is activated for card
Quoted 7 lines
#0. Suggest a bigger
bdl_pos_adj.The final line did not appear when I tried to tune using the new version
[ 1225.904503] tda18271: performing RF tracking filter calibration [ 1230.272003] tda18271: RF tracking filter calibration complete
Michael,
The policy on this mailing list is to reply BELOW the quoted text. Please keep this in mind for the future.
I didn't realize the board had a saa7130 chipset -- That explains a lot. This means that there actually is no tda8290 on the board. (the tda8290 is usually found inside the saa7131 chipset)
You can remove the line, TUNER_PHILIPS_TDA8290 from the card definition in saa7134-cards.c -- replace it with TUNER_ABSENT.
That shouldn't fix the problem, but it would be interesting to hear if it changes anything. I see that communication with the tuner is working properly... It's taking 5 seconds to complete the rf tracking filter calibration in either case, so we know that the line of communication to the tuner itself isn't a problem.
I think this will be easier if we meet in irc. Can you meed me in #linuxtv on irc.freenode.net?
If not, please enable module option debug=1 to tda18271 and send back full dmesg, unedited, including startup of the device and a tune attempt.
Also, enable debug=1 for the tda10048 module -- maybe something changed there. I just tested this code with my ATSC saa7134 board that uses the tda18271, and it's working fine, so I doubt it's the tuner persay, but we should investigate anyway.
-Mike
Quoted 118 lines · Michael Krufky
Quoted 63 lines
2009/11/1 Michael Krufky <[email protected]>:
Quoted 61 lines · Michael Krufky
Quoted 42 lines
Quoted 9 lines · Michael Obst
Hi,
Thanks for fixing this, I can confirm that it now compiles and inserts and the remote works, so does the av input to the tvcard however the card does not seem to be able to tune any channels, I have checked the old driver and that is still able to tune in channels. The output from my dmesg is below.Thanks
Michael ObstMichael,
This is an interesting problem -- the part of your dmesg that stands out to me is this:
Quoted 2 lines
[ 502.928544] tuner 0-0060: chip found @
0xc0(saa7130[0]) [ 502.960501] tda8290: no gate control were provided!That error message was added as a safety measure -- it shouldn't be possible to ever hit that code path. Are you running any non-GPL binary drivers on your system, such as NVIDIA or anything else?
Let me explain:
The "no gate control were provided!" message was added by Mauro to the tda8290 driver, mainly as a check to ensure that we don't call a null function pointer. The gate control is actually provided by the tda8290 driver itself, by either
tda8290_i2c_bridgeortda8295_i2c_bridge, depending on which hardware is present. In your case, it's a tda8290.The function pointer is filled during the
tda829x_attach()function, before we call thetda829x_find_tunerfunction, where this error message is displayed. The only way for this to have occurred, as far as I can tell, is if the probe to detect the tda8290 itself had failed.Have you repeated your test with the same problem each time, or did this only happen once?
Quoted 8 lines
Can you try again, from a cold reboot?
Also, I'm just assuming that this failure occurred during a digital tune -- is that correct? Does analog television work?
If the problem is reproducible, can you also show us dmesg during a failed tune?
I'm very interested in hearing more about this -- please let me know.
Oops, on second look, seems that the error occurred during analog bring-up ... does digital tv work?
-Mike
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.htmlQuoted 19 lines · Michael Obst
This problem is reproducible and occurs the same from a cold boot or inserting saa7134. Analog tv has never worked on this card, I was under the impression there was no analog tuner on the card (looking at
http://www.leadtek.com/eng/tv_tuner/image/digital_tv.pdf). The info was simply from doing a modprobe on saa7134. The only lines in the dmesg that were different from the old driver wassaa7130[0]/alsa: Leadtek Winfast DTV1000S doesn't support digital audio
So I guess the analog part has always failed
I am using the nvidia driver and a driver for my wireless card, I will turn these off and see if I can get a different result.
During tuning for digital tv with the old driver I got
[ 1081.808505] tda18271: performing RF tracking filter calibration [ 1086.152006] tda18271: RF tracking filter calibration complete [ 1091.020535] hda-intel: IRQ timing workaround is activated for cardQuoted 7 lines
#0. Suggest a bigger
bdl_pos_adj.The final line did not appear when I tried to tune using the new version
[ 1225.904503] tda18271: performing RF tracking filter calibration [ 1230.272003] tda18271: RF tracking filter calibration completeMichael,
The policy on this mailing list is to reply BELOW the quoted text. Please keep this in mind for the future.
I didn't realize the board had a saa7130 chipset -- That explains a lot. This means that there actually is no tda8290 on the board. (the tda8290 is usually found inside the saa7131 chipset)
You can remove the line,
TUNER_PHILIPS_TDA8290from the card definition insaa7134-cards.c-- replace it withTUNER_ABSENT.That shouldn't fix the problem, but it would be interesting to hear if it changes anything. I see that communication with the tuner is working properly... It's taking 5 seconds to complete the rf tracking filter calibration in either case, so we know that the line of communication to the tuner itself isn't a problem.
I think this will be easier if we meet in irc. Can you meed me in #linuxtv on irc.freenode.net?
If not, please enable module option debug=1 to tda18271 and send back full dmesg, unedited, including startup of the device and a tune attempt.
Quoted 7 lines
Also, enable debug=1 for the tda10048 module -- maybe something changed there. I just tested this code with my ATSC saa7134 board that uses the tda18271, and it's working fine, so I doubt it's the tuner persay, but we should investigate anyway.
-Mike
For any interested readers, Michael did some testing and helped me to find the cause of the problem... Turns out one of my recent tda18271 changesets broke the std_map override functionality of the tda18271 driver -- I already pushed up a fix and requested merge to the master branch.
For those that want their dtv1000s board working with the latest code, use the following tree:
http://kernellabs.com/hg/~mkrufky/dtv1000s-fix
I will delete the tree once the fix is merged into the v4l-dvb master branch.
-Mike