Skip to contentSkip to conversation

2.6.31.5: /dev/input/event? are gone sometimes

PATCH Harald Dunkel 2 participants 2 messages Oct 24, 2009

lore
Share & tools
lore
#0 lore raw

Hi folks,

Sometimes (by chance, as it seems) the /dev/input/event? devices are not working after power-on or reboot. They are not listed in /proc/bus/input/devices. The mouse in X is not moving, keyboard is dead, etc. All I can do is reboot and hope.

Below you can find the diff of /proc/bus/input/devices between a bad and a good start.

udev is 146-5 (included with Debian Sid).

Any helpful hints would be highly appreciated. Of course I can send you the .config, if there is some interest.

Regards

Harri
===================================================================
% diff -u devices.bad devices.good

devices.good 2009-10-24 15:17:17.000000000 +0200 renamed from devices.bad 2009-10-24 15:08:24.000000000 +0200 +22 -4
@@ -3,7 +3,7 @@
 P: Phys=isa0060/serio0/input0
 S: Sysfs=/devices/platform/i8042/serio0/input/input0
 U: Uniq=
-H: Handlers=kbd
+H: Handlers=kbd event0
 B: EV=120013
 B: KEY=402000000 3803078f800d001 feffffdfffefffff fffffffffffffffe
 B: MSC=10
@@ -14,7 +14,7 @@
 P: Phys=usb-0000:00:1a.2-2/input0
 S: Sysfs=/devices/pci0000:00/0000:00:1a.2/usb5/5-2/5-2:1.0/input/input1
 U: Uniq=
-H: Handlers=kbd
+H: Handlers=kbd event1
 B: EV=120013
 B: KEY=1000000000007 ff980000000007ff febeffdfffefffff fffffffffffffffe
 B: MSC=10
@@ -25,7 +25,7 @@
 P: Phys=usb-0000:00:1a.2-2/input1
 S: Sysfs=/devices/pci0000:00/0000:00:1a.2/usb5/5-2/5-2:1.1/input/input2
 U: Uniq=
-H: Handlers=kbd mouse0
+H: Handlers=kbd mouse0 event2
 B: EV=17
 B: KEY=1f001f 2020000 3878d801d001 1e000000000000 0
 B: REL=103
@@ -36,7 +36,25 @@
 P: Phys=isa0061/input0
 S: Sysfs=/devices/platform/pcspkr/input/input3
 U: Uniq=
-H: Handlers=kbd
+H: Handlers=kbd event3
 B: EV=40001
 B: SND=6
 
+I: Bus=0019 Vendor=0000 Product=0001 Version=0000
+N: Name="Power Button"
+P: Phys=LNXPWRBN/button/input0
+S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
+U: Uniq=
+H: Handlers=kbd event4
+B: EV=3
+B: KEY=10000000000000 0
+
+I: Bus=0019 Vendor=0000 Product=0001 Version=0000
+N: Name="Power Button"
+P: Phys=PNP0C0C/button/input0
+S: Sysfs=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
+U: Uniq=
+H: Handlers=kbd event5
+B: EV=3
+B: KEY=10000000000000 0
+
#1 lore raw

Hi Harald,

Quoted 26 lines · Harald Dunkel

Hi folks,

Sometimes (by chance, as it seems) the /dev/input/event? devices are not working after power-on or reboot. They are not listed in /proc/bus/input/devices. The mouse in X is not moving, keyboard is dead, etc. All I can do is reboot and hope.

Below you can find the diff of /proc/bus/input/devices between a bad and a good start.

udev is 146-5 (included with Debian Sid).

Any helpful hints would be highly appreciated. Of course I can send you the .config, if there is some interest.

Regards

Harri
===================================================================
% diff -u devices.bad devices.good

devices.good 2009-10-24 15:17:17.000000000 +0200 line 6

Quoted 5 lines
devices.good 2009-10-24 15:17:17.000000000 +0200 renamed from devices.bad 2009-10-24 15:08:24.000000000 +0200 +1 -1
@@ -3,7 +3,7 @@
 P: Phys=isa0060/serio0/input0
 S: Sysfs=/devices/platform/i8042/serio0/input/input0
 U: Uniq=
-H: Handlers=kbd
+H: Handlers=kbd event0

Since evdev binds to -every_ input device registered its absence in the handlers list suggests that the module is not loaded. I am not sure how and when your distribution loads evdev; try making it built-in to avoid cases when it is not loaded for one reason or another.

Signature · 1 line
Dmitry