Skip to contentSkip to conversation

samsung: move DRAM parameters

PATCH New Seunghyeon Rhee (이승현) 2 participants 4 messages Nov 4, 2009 – Nov 5, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 samsung: move DRAM parameters

Move the definitions of DRAM parameters from SoC description (s3c6400.h) to board description (smdk6400.h). DRAM parameters are rather board-specific than SoC specific. According to the current source, one may have to change the definitions in s3c6400.h in addition to creating the new board description whenever he wants to add support for a new board based on s3c6400. I don't think this meets the U-Boot policy of separating SoC description and board description. There will be no observable changes in operation. It's just to make it easier to add support for new boards.

---
 include/configs/smdk6400.h |   21 +++++++++++++++++++++
 include/s3c6400.h          |   21 ---------------------
 2 files changed, 21 insertions(+), 21 deletions(-)
include/configs/smdk6400.h +21 -0
index f6e1221..a2b46fd 100644
@@ -309,4 +309,25 @@
 # error "usb_ohci.c is currently broken with MMU enabled."
 #endif
 
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define DMC1_MEM_CFG	0x80010012	/* Chip1, Burst4, Row/Column bit */
+#define DMC1_MEM_CFG2	0xB45
+#define DMC1_CHIP0_CFG	0x150F8		/* 0x4000_0000 ~ 0x43ff_ffff (64MB) */
+#define DMC_DDR_32_CFG	0x0 		/* 32bit, DDR */
+
+/* Memory Parameters */
+/* DDR Parameters */
+#define DDR_tREFRESH		7800	/* ns */
+#define DDR_tRAS		45	/* ns (min: 45ns)*/
+#define DDR_tRC 		68	/* ns (min: 67.5ns)*/
+#define DDR_tRCD		23	/* ns (min: 22.5ns)*/
+#define DDR_tRFC		80	/* ns (min: 80ns)*/
+#define DDR_tRP 		23	/* ns (min: 22.5ns)*/
+#define DDR_tRRD		15	/* ns (min: 15ns)*/
+#define DDR_tWR 		15	/* ns (min: 15ns)*/
+#define DDR_tXSR		120	/* ns (min: 120ns)*/
+#define DDR_CASL		3	/* CAS Latency 3 */
+
 #endif	/* __CONFIG_H */
include/s3c6400.h +0 -21
index e527c08..34d0d15 100644
@@ -814,27 +814,6 @@
 #endif
 
 
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define DMC1_MEM_CFG	0x80010012	/* Chip1, Burst4, Row/Column bit */
-#define DMC1_MEM_CFG2	0xB45
-#define DMC1_CHIP0_CFG	0x150F8		/* 0x4000_0000 ~ 0x43ff_ffff (64MB) */
-#define DMC_DDR_32_CFG	0x0 		/* 32bit, DDR */
-
-/* Memory Parameters */
-/* DDR Parameters */
-#define DDR_tREFRESH		7800	/* ns */
-#define DDR_tRAS		45	/* ns (min: 45ns)*/
-#define DDR_tRC 		68	/* ns (min: 67.5ns)*/
-#define DDR_tRCD		23	/* ns (min: 22.5ns)*/
-#define DDR_tRFC		80	/* ns (min: 80ns)*/
-#define DDR_tRP 		23	/* ns (min: 22.5ns)*/
-#define DDR_tRRD		15	/* ns (min: 15ns)*/
-#define DDR_tWR 		15	/* ns (min: 15ns)*/
-#define DDR_tXSR		120	/* ns (min: 120ns)*/
-#define DDR_CASL		3	/* CAS Latency 3 */
-
 /*
  * mDDR memory configuration
  */
Signature · 8 lines
1.6.2.5


-- 
Seunghyeon Rhee, Ph.D. / Director
LPM Technology Inc.
T +82-70-8255-6007  F +82-2-6442-6462
M +82-10-2790-0657
#1 lore raw

PATCH 1/1 samsung: move DRAM parameters

Dear Seunghyeon Rhee,

2009/11/4 "Seunghyeon Rhee (???)" <[email protected]>:

Quoted 83 lines

Move the definitions of DRAM parameters from SoC description (s3c6400.h) to board description (smdk6400.h). DRAM parameters are rather board-specific than SoC specific. According to the current source, one may have to change the definitions in s3c6400.h in addition to creating the new board description whenever he wants to add support for a new board based on s3c6400. I don't think this meets the U-Boot policy of separating SoC description and board description. There will be no observable changes in operation. It's just to make it easier to add support for new boards.

---
?include/configs/smdk6400.h | ? 21 +++++++++++++++++++++ ?include/s3c6400.h ? ? ? ? ?| ? 21 --------------------- ?2 files changed, 21 insertions(+), 21 deletions(-)

include/configs/smdk6400.h +0 -0
index f6e1221..a2b46fd 100644
@@ -309,4 +309,25 @@

?# error "usb_ohci.c is currently broken with MMU enabled." ?#endif

include/configs/smdk6400.h +21 -0
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define DMC1_MEM_CFG ? 0x80010012 ? ? ?/* Chip1, Burst4, Row/Column bit */
+#define DMC1_MEM_CFG2 ?0xB45
+#define DMC1_CHIP0_CFG 0x150F8 ? ? ? ? /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */
+#define DMC_DDR_32_CFG 0x0 ? ? ? ? ? ? /* 32bit, DDR */
+
+/* Memory Parameters */
+/* DDR Parameters */
+#define DDR_tREFRESH ? ? ? ? ? 7800 ? ?/* ns */
+#define DDR_tRAS ? ? ? ? ? ? ? 45 ? ? ?/* ns (min: 45ns)*/
+#define DDR_tRC ? ? ? ? ? ? ? ?68 ? ? ?/* ns (min: 67.5ns)*/
+#define DDR_tRCD ? ? ? ? ? ? ? 23 ? ? ?/* ns (min: 22.5ns)*/
+#define DDR_tRFC ? ? ? ? ? ? ? 80 ? ? ?/* ns (min: 80ns)*/
+#define DDR_tRP ? ? ? ? ? ? ? ?23 ? ? ?/* ns (min: 22.5ns)*/
+#define DDR_tRRD ? ? ? ? ? ? ? 15 ? ? ?/* ns (min: 15ns)*/
+#define DDR_tWR ? ? ? ? ? ? ? ?15 ? ? ?/* ns (min: 15ns)*/
+#define DDR_tXSR ? ? ? ? ? ? ? 120 ? ? /* ns (min: 120ns)*/
+#define DDR_CASL ? ? ? ? ? ? ? 3 ? ? ? /* CAS Latency 3 */
+

?#endif /* __CONFIG_H */

include/s3c6400.h +0 -0
index e527c08..34d0d15 100644
@@ -814,27 +814,6 @@

?#endif

include/s3c6400.h +0 -21
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define DMC1_MEM_CFG ? 0x80010012 ? ? ?/* Chip1, Burst4, Row/Column bit */
-#define DMC1_MEM_CFG2 ?0xB45
-#define DMC1_CHIP0_CFG 0x150F8 ? ? ? ? /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */
-#define DMC_DDR_32_CFG 0x0 ? ? ? ? ? ? /* 32bit, DDR */
-
-/* Memory Parameters */
-/* DDR Parameters */
-#define DDR_tREFRESH ? ? ? ? ? 7800 ? ?/* ns */
-#define DDR_tRAS ? ? ? ? ? ? ? 45 ? ? ?/* ns (min: 45ns)*/
-#define DDR_tRC ? ? ? ? ? ? ? ?68 ? ? ?/* ns (min: 67.5ns)*/
-#define DDR_tRCD ? ? ? ? ? ? ? 23 ? ? ?/* ns (min: 22.5ns)*/
-#define DDR_tRFC ? ? ? ? ? ? ? 80 ? ? ?/* ns (min: 80ns)*/
-#define DDR_tRP ? ? ? ? ? ? ? ?23 ? ? ?/* ns (min: 22.5ns)*/
-#define DDR_tRRD ? ? ? ? ? ? ? 15 ? ? ?/* ns (min: 15ns)*/
-#define DDR_tWR ? ? ? ? ? ? ? ?15 ? ? ?/* ns (min: 15ns)*/
-#define DDR_tXSR ? ? ? ? ? ? ? 120 ? ? /* ns (min: 120ns)*/
-#define DDR_CASL ? ? ? ? ? ? ? 3 ? ? ? /* CAS Latency 3 */
-

?/*
?* mDDR memory configuration
?*/
--
1.6.2.5

Quoted 10 lines

--
Seunghyeon Rhee, Ph.D. / Director
LPM Technology Inc.
T +82-70-8255-6007 ?F +82-2-6442-6462
M +82-10-2790-0657
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

yes,
DRAM parameters are board specific.
But I think it is not good way to move DRAM parameters to board configuration file.
At first, we need to move cpu/arm1176/s3c64xx/cpu_init.S to board directory. (please see smdkc100/mem_setup.S)
And.. let's think about where to move DRAM parameters. Please give your opinion.

Thanks
Minkyu Kang

Signature · 2 lines
from. prom.
www.promsoft.net
#2 lore raw

PATCH 1/1 samsung: move DRAM parameters

Dear Minkyu Kang,

What causes the current ambiguity is, in my opinion, the "parameters" themselves and "the way of setting them." As you know, DRAM controller is integrated in the SoC while the parameters required to set them are dependent on the external components, DRAM chips.

In this respect, cpu_init.S - I don't like the name because all it does is set up the memory controller. mem_setup.S is more appropriate - don't need to be moved to board description stuffs. The memory controller (the hardware logic in the SoC) is not changeable according to the board design. Neither does the way of setting it, which is in charge of cpu_init.S. What is
changed from board to board is not cpu_init.S but the parameters. If we move it to board directory, we have to add redundant code - actually several copies of the same file - every time we add support for a new board with the same SoC.

Thererfore, I think cpu_init.S(or mem_setup.S) would better be placed with SoC stuffs like it is now while DRAM parameters be moved to board description stuffs. We can make the function for setting up the DRAM controller completely independent of board design by introducing more macro definitions if necessary. All we have to do for adding support for new boards then will be reduced to creating the new board's description. No redundant codes, no repeated modification of the SoC description will be required.

Best regards,
Seunghyeon

Seunghyeon Rhee, Ph.D. / Director
LPM Technology Inc.
T +82-70-8255-6007 F +82-2-6442-6462
M +82-10-2790-0657

Minkyu Kang ? ?:

Quoted 111 lines

Dear Seunghyeon Rhee,

2009/11/4 "Seunghyeon Rhee (???)" <[email protected]>:

Quoted 83 lines

Move the definitions of DRAM parameters from SoC description (s3c6400.h) to board description (smdk6400.h). DRAM parameters are rather board-specific than SoC specific. According to the current source, one may have to change the definitions in s3c6400.h in addition to creating the new board description whenever he wants to add support for a new board based on s3c6400. I don't think this meets the U-Boot policy of separating SoC description and board description. There will be no observable changes in operation. It's just to make it easier to add support for new boards.

---
 include/configs/smdk6400.h |   21 +++++++++++++++++++++
 include/s3c6400.h          |   21 ---------------------
 2 files changed, 21 insertions(+), 21 deletions(-)
include/configs/smdk6400.h +21 -0
index f6e1221..a2b46fd 100644
@@ -309,4 +309,25 @@
 # error "usb_ohci.c is currently broken with MMU enabled."
 #endif
 
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define DMC1_MEM_CFG   0x80010012      /* Chip1, Burst4, Row/Column bit */
+#define DMC1_MEM_CFG2  0xB45
+#define DMC1_CHIP0_CFG 0x150F8         /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */
+#define DMC_DDR_32_CFG 0x0             /* 32bit, DDR */
+
+/* Memory Parameters */
+/* DDR Parameters */
+#define DDR_tREFRESH           7800    /* ns */
+#define DDR_tRAS               45      /* ns (min: 45ns)*/
+#define DDR_tRC                68      /* ns (min: 67.5ns)*/
+#define DDR_tRCD               23      /* ns (min: 22.5ns)*/
+#define DDR_tRFC               80      /* ns (min: 80ns)*/
+#define DDR_tRP                23      /* ns (min: 22.5ns)*/
+#define DDR_tRRD               15      /* ns (min: 15ns)*/
+#define DDR_tWR                15      /* ns (min: 15ns)*/
+#define DDR_tXSR               120     /* ns (min: 120ns)*/
+#define DDR_CASL               3       /* CAS Latency 3 */
+
 #endif /* __CONFIG_H */
include/s3c6400.h +0 -22
index e527c08..34d0d15 100644
@@ -814,27 +814,6 @@
 #endif
 
 
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define DMC1_MEM_CFG   0x80010012      /* Chip1, Burst4, Row/Column bit */
-#define DMC1_MEM_CFG2  0xB45
-#define DMC1_CHIP0_CFG 0x150F8         /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */
-#define DMC_DDR_32_CFG 0x0             /* 32bit, DDR */
-
-/* Memory Parameters */
-/* DDR Parameters */
-#define DDR_tREFRESH           7800    /* ns */
-#define DDR_tRAS               45      /* ns (min: 45ns)*/
-#define DDR_tRC                68      /* ns (min: 67.5ns)*/
-#define DDR_tRCD               23      /* ns (min: 22.5ns)*/
-#define DDR_tRFC               80      /* ns (min: 80ns)*/
-#define DDR_tRP                23      /* ns (min: 22.5ns)*/
-#define DDR_tRRD               15      /* ns (min: 15ns)*/
-#define DDR_tWR                15      /* ns (min: 15ns)*/
-#define DDR_tXSR               120     /* ns (min: 120ns)*/
-#define DDR_CASL               3       /* CAS Latency 3 */
-
 /*
 * mDDR memory configuration
 */
--

1.6.2.5

Quoted 11 lines

--
Seunghyeon Rhee, Ph.D. / Director
LPM Technology Inc.
T +82-70-8255-6007 F +82-2-6442-6462
M +82-10-2790-0657
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

yes,
DRAM parameters are board specific.
But I think it is not good way to move DRAM parameters to board configuration file.
At first, we need to move cpu/arm1176/s3c64xx/cpu_init.S to board directory. (please see smdkc100/mem_setup.S)
And.. let's think about where to move DRAM parameters. Please give your opinion.

Thanks
Minkyu Kang

#3 lore raw

PATCH 1/1 samsung: move DRAM parameters

Dear Seunghyeon Rhee,

please do not top posting.

2009/11/5 "Seunghyeon Rhee (???)" <[email protected]>:

Quoted 18 lines

Dear Minkyu Kang,

What causes the current ambiguity is, in my opinion, the "parameters" themselves and "the way of setting them." As you know, DRAM controller is integrated in the SoC while the parameters required to set them are dependent on the external components, DRAM chips.

In this respect, cpu_init.S - I don't like the name because all it does is set up the memory controller. mem_setup.S is more appropriate - don't need to be moved to board description stuffs. The memory controller (the hardware logic in the SoC) is not changeable according to the board design. Neither does the way of setting it, which is in charge of cpu_init.S. What is
changed from board to board is not cpu_init.S but the parameters. If we move it to board directory, we have to add redundant code - actually several copies of the same file - every time we add support for a new board with the same SoC.

Quoted 8 lines

Thererfore, I think cpu_init.S(or mem_setup.S) would better be placed with SoC stuffs like it is now while DRAM parameters be moved to board description stuffs. We can make the function for setting up the DRAM controller completely independent of board design by introducing more macro definitions if necessary. All we have to do for adding support for new boards then will be reduced to creating the new board's description. No redundant codes, no repeated modification of the SoC description will be required.

Agreed.
But, I'm not sure that move it to board configuration file. let's figure out and discuss.. including regard your suggestion.

Quoted 120 lines

Best regards,
Seunghyeon

Seunghyeon Rhee, Ph.D. / Director
LPM Technology Inc.
T +82-70-8255-6007 F +82-2-6442-6462
M +82-10-2790-0657

Minkyu Kang ? ?:

Quoted 108 lines

Dear Seunghyeon Rhee,

2009/11/4 "Seunghyeon Rhee (???)" <[email protected]>:

Quoted 83 lines

Move the definitions of DRAM parameters from SoC description (s3c6400.h) to board description (smdk6400.h). DRAM parameters are rather board-specific than SoC specific. According to the current source, one may have to change the definitions in s3c6400.h in addition to creating the new board description whenever he wants to add support for a new board based on s3c6400. I don't think this meets the U-Boot policy of separating SoC description and board description. There will be no observable changes in operation. It's just to make it easier to add support for new boards.

---
 include/configs/smdk6400.h |   21 +++++++++++++++++++++
 include/s3c6400.h          |   21 ---------------------
 2 files changed, 21 insertions(+), 21 deletions(-)
include/configs/smdk6400.h +21 -0
index f6e1221..a2b46fd 100644
@@ -309,4 +309,25 @@
 # error "usb_ohci.c is currently broken with MMU enabled."
 #endif
 
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define DMC1_MEM_CFG   0x80010012      /* Chip1, Burst4, Row/Column bit */
+#define DMC1_MEM_CFG2  0xB45
+#define DMC1_CHIP0_CFG 0x150F8         /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */
+#define DMC_DDR_32_CFG 0x0             /* 32bit, DDR */
+
+/* Memory Parameters */
+/* DDR Parameters */
+#define DDR_tREFRESH           7800    /* ns */
+#define DDR_tRAS               45      /* ns (min: 45ns)*/
+#define DDR_tRC                68      /* ns (min: 67.5ns)*/
+#define DDR_tRCD               23      /* ns (min: 22.5ns)*/
+#define DDR_tRFC               80      /* ns (min: 80ns)*/
+#define DDR_tRP                23      /* ns (min: 22.5ns)*/
+#define DDR_tRRD               15      /* ns (min: 15ns)*/
+#define DDR_tWR                15      /* ns (min: 15ns)*/
+#define DDR_tXSR               120     /* ns (min: 120ns)*/
+#define DDR_CASL               3       /* CAS Latency 3 */
+
 #endif /* __CONFIG_H */
include/s3c6400.h +0 -22
index e527c08..34d0d15 100644
@@ -814,27 +814,6 @@
 #endif
 
 
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define DMC1_MEM_CFG   0x80010012      /* Chip1, Burst4, Row/Column bit */
-#define DMC1_MEM_CFG2  0xB45
-#define DMC1_CHIP0_CFG 0x150F8         /* 0x4000_0000 ~ 0x43ff_ffff (64MB) */
-#define DMC_DDR_32_CFG 0x0             /* 32bit, DDR */
-
-/* Memory Parameters */
-/* DDR Parameters */
-#define DDR_tREFRESH           7800    /* ns */
-#define DDR_tRAS               45      /* ns (min: 45ns)*/
-#define DDR_tRC                68      /* ns (min: 67.5ns)*/
-#define DDR_tRCD               23      /* ns (min: 22.5ns)*/
-#define DDR_tRFC               80      /* ns (min: 80ns)*/
-#define DDR_tRP                23      /* ns (min: 22.5ns)*/
-#define DDR_tRRD               15      /* ns (min: 15ns)*/
-#define DDR_tWR                15      /* ns (min: 15ns)*/
-#define DDR_tXSR               120     /* ns (min: 120ns)*/
-#define DDR_CASL               3       /* CAS Latency 3 */
-
 /*
 * mDDR memory configuration
 */
--

1.6.2.5

Quoted 11 lines

--
Seunghyeon Rhee, Ph.D. / Director
LPM Technology Inc.
T +82-70-8255-6007 F +82-2-6442-6462
M +82-10-2790-0657
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

yes,
DRAM parameters are board specific.
But I think it is not good way to move DRAM parameters to board configuration file.
At first, we need to move cpu/arm1176/s3c64xx/cpu_init.S to board directory. (please see smdkc100/mem_setup.S)
And.. let's think about where to move DRAM parameters. Please give your opinion.

Quoted 8 lines
Quoted 3 lines

Thanks
Minkyu Kang

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Thanks
Minkyu Kang

Signature · 2 lines
from. prom.
www.promsoft.net