gspca pac7302: add debug register write interface
PATCH 2/2 gspca pac7302: add debug register write interface
From: Márton Németh <[email protected]>
Add debug register write interface to pac7302 to be able to set for example the edge detect mode (bit 2 register 0x55) or the test pattern (bit 0..3, register 0x72) and test overlay (bit 4, register 0x72) from the user space. Only write of register page 0 is supported by this patch.
The patch was tested together with Labtec Webcam 2200 (USB ID 093a:2626).
---
This patch replaces http://linuxtv.org/hg/~jfrancois/v4l-dvb/rev/da22d3ea5fc7 and
http://linuxtv.org/hg/~jfrancois/v4l-dvb/rev/9b3580f8fee8 .
---
linux/drivers/media/video/gspca/pac7302.c +54 -0
@@ -53,6 +53,7 @@#define MODULE_NAME "pac7302" +#include <media/v4l2-chip-ident.h> #include "gspca.h" MODULE_AUTHOR ("Thomas Kaiser [email protected]" );
@@ -982,6 +983,55 @@ static int sd_getvflip(struct gspca_devreturn 0 ; } +#ifdef CONFIG_VIDEO_ADV_DEBUG +static int sd_dbg_s_register (struct gspca_dev *gspca_dev, +struct v4l2_dbg_register *reg) +{ +int ret = -EINVAL ; +__u8 index; +__u8 value; + +/* reg->reg: bit0..15: reserved for register index (wIndex is 16bit +long on the USB bus) +*/ +if (reg->match.type ==V4L2_CHIP_MATCH_HOST && + reg->match.addr ==0 && + (reg->reg <0x000000ff ) && + (reg->val <=0x000000ff ) + ) { +/* Currently writing to page 0 is only supported. */ +/* reg_w() only supports 8bit index */ + index = reg->reg &0x000000ff ; + value = reg->val &0x000000ff ; + +/* Note that there shall be no access to other page +by any other function between the page swith and +the actual register write */ + ret =reg_w (gspca_dev,0xff ,0x00 );/* page 0 */ +if (0 <= ret) + ret =reg_w (gspca_dev, index, value); + +if (0 <= ret) + ret =reg_w (gspca_dev,0xdc ,0x01 ); + } +return ret; +} + +static int sd_chip_ident (struct gspca_dev *gspca_dev, +struct v4l2_dbg_chip_ident *chip) +{ +int ret = -EINVAL ; + +if (chip->match.type ==V4L2_CHIP_MATCH_HOST && + chip->match.addr ==0 ) { + chip->revision =0 ; + chip->ident =V4L2_IDENT_UNKNOWN ; + ret =0 ; + } +return ret; +} +#endif +/* sub-driver description for pac7302 */ static struct sd_desc sd_desc = { .name =MODULE_NAME ,
@@ -994,6 +1044,10 @@ static struct sd_desc sd_desc = { .stop0 = sd_stop0, .pkt_scan = sd_pkt_scan, .dq_callback = do_autogain, +#ifdef CONFIG_VIDEO_ADV_DEBUG + .set_register = sd_dbg_s_register, + .get_chip_ident = sd_chip_ident, +#endif };/* -- module initialisation -- */
From: Márton Németh <[email protected]>
Add debug register write interface to pac7302 to be able to set for example the edge detect mode (bit 2 register 0x55) or the test pattern (bit 0..3, register 0x72) and test overlay (bit 4, register 0x72) from the user space. Only write of register page 0 is supported by this patch.
The patch was tested together with Labtec Webcam 2200 (USB ID 093a:2626).
---
The patch is based on 13335:3fd924da7091 from http://linuxtv.org/hg/~jfrancois/gspca/ .
---
linux/drivers/media/video/gspca/pac7302.c +54 -0
@@ -68,6 +68,7 @@#define MODULE_NAME "pac7302" +#include <media/v4l2-chip-ident.h> #include "gspca.h" MODULE_AUTHOR ("Thomas Kaiser [email protected]" );
@@ -1164,6 +1165,55 @@return 0 ; } +#ifdef CONFIG_VIDEO_ADV_DEBUG +static int sd_dbg_s_register (struct gspca_dev *gspca_dev, +struct v4l2_dbg_register *reg) +{ +int ret = -EINVAL ; +__u8 index; +__u8 value; + +/* reg->reg: bit0..15: reserved for register index (wIndex is 16bit +long on the USB bus) +*/ +if (reg->match.type ==V4L2_CHIP_MATCH_HOST && + reg->match.addr ==0 && + (reg->reg <0x000000ff ) && + (reg->val <=0x000000ff ) + ) { +/* Currently writing to page 0 is only supported. */ +/* reg_w() only supports 8bit index */ + index = reg->reg &0x000000ff ; + value = reg->val &0x000000ff ; + +/* Note that there shall be no access to other page +by any other function between the page swith and +the actual register write */ + ret =reg_w (gspca_dev,0xff ,0x00 );/* page 0 */ +if (0 <= ret) + ret =reg_w (gspca_dev, index, value); + +if (0 <= ret) + ret =reg_w (gspca_dev,0xdc ,0x01 ); + } +return ret; +} + +static int sd_chip_ident (struct gspca_dev *gspca_dev, +struct v4l2_dbg_chip_ident *chip) +{ +int ret = -EINVAL ; + +if (chip->match.type ==V4L2_CHIP_MATCH_HOST && + chip->match.addr ==0 ) { + chip->revision =0 ; + chip->ident =V4L2_IDENT_UNKNOWN ; + ret =0 ; + } +return ret; +} +#endif +/* sub-driver description for pac7302 */ static struct sd_desc sd_desc = { .name =MODULE_NAME ,
@@ -1176,6 +1226,10 @@ .stop0 = sd_stop0, .pkt_scan = sd_pkt_scan, .dq_callback = do_autogain, +#ifdef CONFIG_VIDEO_ADV_DEBUG + .set_register = sd_dbg_s_register, + .get_chip_ident = sd_chip_ident, +#endif };/* -- module initialisation -- */