Skip to contentSkip to conversation

Terratec Cinergy 600 TV MK3: Problem with Radio/RDS

DISCUSSION Roland Egli 3 participants 5 messages Nov 9, 2009 – Nov 12, 2009 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

Hi all

I have the TV card "Terratec Cinergy 600 TV MK3" with SAA7134HL. The tuner is a Philips FM1216ME/H-3 and there is an additional RDS decoder SAA6588T.

For loading the module I use

$ modprobe saa7134 card=48 tuner=38

TV works fine, but I have a problem with the radio. The sound is very noisy, not stereo and there is as well no RDS reception (saa6588 module is loaded as well).

The following infos go to the log:

Nov  9 21:33:52 oslo kernel: [ 1667.403249] saa7130/34: v4l2 driver version 0.2.15 loaded
Nov  9 21:33:52 oslo kernel: [ 1667.403319] saa7134[0]: found at 0000:02:0b.0, rev: 1, irq: 23, latency: 64, mmio: 0xfeaff400
Nov  9 21:33:52 oslo kernel: [ 1667.403330] saa7134[0]: subsystem: 153b:1158, board: Terratec Cinergy 600 TV MK3 [card=48,insmod option]
Nov  9 21:33:52 oslo kernel: [ 1667.403365] saa7134[0]: board init: gpio is 50000
Nov  9 21:33:52 oslo kernel: [ 1667.403483] input: saa7134 IR (Terratec Cinergy 60 as /devices/pci0000:00/0000:00:1e.0/0000:02:0b.0/input/input7
Nov  9 21:33:52 oslo kernel: [ 1667.403567] IRQ 23/saa7134[0]: IRQF_DISABLED is not guaranteed on shared IRQs
Nov  9 21:33:52 oslo kernel: [ 1667.559198] saa7134[0]: i2c eeprom 00: 3b 15 58 11 ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559225] saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559251] saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559276] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559300] saa7134[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559326] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559351] saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559376] saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559400] saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559425] saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559450] saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559475] saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559500] saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559524] saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559549] saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559574] saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Nov  9 21:33:52 oslo kernel: [ 1667.559602] i2c-adapter i2c-0: Invalid 7-bit address 0x7a
Nov  9 21:33:52 oslo kernel: [ 1667.592173] tuner 0-0043: chip found @ 0x86 (saa7134[0])
Nov  9 21:33:52 oslo kernel: [ 1667.592284] tda9887 0-0043: creating new instance
Nov  9 21:33:52 oslo kernel: [ 1667.592287] tda9887 0-0043: tda988[5/6/7] found
Nov  9 21:33:52 oslo kernel: [ 1667.632092] All bytes are equal. It is not a TEA5767
Nov  9 21:33:52 oslo kernel: [ 1667.632309] tuner 0-0060: chip found @ 0xc0 (saa7134[0])
Nov  9 21:33:52 oslo kernel: [ 1667.646672] tuner-simple 0-0060: creating new instance
Nov  9 21:33:52 oslo kernel: [ 1667.646680] tuner-simple 0-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
Nov  9 21:33:52 oslo kernel: [ 1667.736118] saa6588 0-0010: saa6588 found @ 0x20 (saa7134[0])
Nov  9 21:33:52 oslo kernel: [ 1667.744073] saa7134[0]: found RDS decoder
Nov  9 21:33:52 oslo kernel: [ 1667.752207] saa7134[0]: registered device video1 [v4l2]
Nov  9 21:33:52 oslo kernel: [ 1667.752276] saa7134[0]: registered device vbi0
Nov  9 21:33:52 oslo kernel: [ 1667.752337] saa7134[0]: registered device radio0
Nov  9 21:33:52 oslo kernel: [ 1667.768981] saa7134 ALSA driver for DMA sound loaded
Nov  9 21:33:52 oslo kernel: [ 1667.769069] IRQ 23/saa7134[0]: IRQF_DISABLED is not guaranteed on shared IRQs
Nov  9 21:33:52 oslo kernel: [ 1667.769109] saa7134[0]/alsa: saa7134[0] at 0xfeaff400 irq 23 registered as card -2

Does anyone have an idea about the reason for this problem or even better a solution? Does anyone use the same card without problem?

Many thanks in advance.
Roland

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

#1 lore raw
Quoted 6 lines · Roland Egli

Hi all

I have the TV card "Terratec Cinergy 600 TV MK3" with SAA7134HL. The tuner is a Philips FM1216ME/H-3 and there is an additional RDS decoder SAA6588T.

Quoted 6 lines

For loading the module I use

$ modprobe saa7134 card=48 tuner=38

TV works fine, but I have a problem with the radio. The sound is very noisy, not stereo and there is as well no RDS reception (saa6588 module is loaded as well).

For RDS reception, you need a strong signal since the RDS carrier's level is well below the audio carrier level. Your only chance is to improve reception. What kind of antenna are you using? Are you sure it's connected to the _radio_ antenna jack and not the TV?

Thanks,
Hans

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

#2 lore raw

Hi,

Am Dienstag, den 10.11.2009, 15:50 +0100 schrieb Hans J. Koch:

Quoted 14 lines · Roland Egli
Quoted 6 lines

Hi all

I have the TV card "Terratec Cinergy 600 TV MK3" with SAA7134HL. The tuner is a Philips FM1216ME/H-3 and there is an additional RDS decoder SAA6588T.

Quoted 6 lines

For loading the module I use

$ modprobe saa7134 card=48 tuner=38

TV works fine, but I have a problem with the radio. The sound is very noisy, not stereo and there is as well no RDS reception (saa6588 module is loaded as well).

Quoted 8 lines

For RDS reception, you need a strong signal since the RDS carrier's level is well below the audio carrier level. Your only chance is to improve reception. What kind of antenna are you using? Are you sure it's connected to the _radio_ antenna jack and not the TV?

Thanks,
Hans

Hans, for what I know it makes no difference on that tuner, if radio comes in from the TV antenna connector or from the radio connector.

At least we don't have some dedicated separating RF input switch for that.

For example, the other way round, if you have a cable TV provider also providing radio, and radio freqs are not filtered from the TV input connected, radio will just work fine from the TV antenna connector and likely are all stereo. I can't tell anything for RDS.

If you now also connect that cheap rabbit ears antenna mostly coming with such cards, this might lead to overlapping frequencies noticed as too much noise on radio. Maybe we still miss something, but it is not in the tuner specs.

Me and one single other guy reported loud thrilling noise for radio if tuned into off on later driver revisions. I'm still not sure, if it is only caused by machine specific interferences, a network cable had some impact on it, but I saw/heard it later also on FMD hybrid devices on a different machine.

To connect the rabbit ears to the radio antenna connector will turn that annoying noise into normal static. On that FMD hybrid you usually will have the better radio reception from a roof mounted antenna for DVB-T and there is also no active RF input switching like we only saw it later on silicon hybrid devices.

For radio stereo it needs still some v4l2 app and kradio and mplayer with v4l2 radio support are still the best candidates, but I'm not on latest on radio apps around currently.

Reception improvement is of course still the best key for all.

Thanks,
Hermann

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

#3 lore raw
Quoted 53 lines · hermann pitton

Hi,

Am Dienstag, den 10.11.2009, 15:50 +0100 schrieb Hans J. Koch:

Quoted 11 lines · Roland Egli
Quoted 10 lines

Hi all

I have the TV card "Terratec Cinergy 600 TV MK3" with SAA7134HL. The tuner is a Philips FM1216ME/H-3 and there is an additional RDS decoder SAA6588T.

For loading the module I use

$ modprobe saa7134 card=48 tuner=38

TV works fine, but I have a problem with the radio. The sound is very noisy, not stereo and there is as well no RDS reception (saa6588 module is loaded as well).

Quoted 9 lines

For RDS reception, you need a strong signal since the RDS carrier's level is well below the audio carrier level. Your only chance is to improve reception. What kind of antenna are you using? Are you sure it's connected to the _radio_ antenna jack and not the TV?

Thanks,
Hans

Hans, for what I know it makes no difference on that tuner, if radio comes in from the TV antenna connector or from the radio connector.

At least we don't have some dedicated separating RF input switch for that.

For example, the other way round, if you have a cable TV provider also providing radio, and radio freqs are not filtered from the TV input connected, radio will just work fine from the TV antenna connector and likely are all stereo. I can't tell anything for RDS.

If you now also connect that cheap rabbit ears antenna mostly coming with such cards, this might lead to overlapping frequencies noticed as too much noise on radio. Maybe we still miss something, but it is not in the tuner specs.

Me and one single other guy reported loud thrilling noise for radio if tuned into off on later driver revisions. I'm still not sure, if it is only caused by machine specific interferences, a network cable had some impact on it, but I saw/heard it later also on FMD hybrid devices on a different machine.

To connect the rabbit ears to the radio antenna connector will turn that annoying noise into normal static. On that FMD hybrid you usually will have the better radio reception from a roof mounted antenna for DVB-T and there is also no active RF input switching like we only saw it later on silicon hybrid devices.

Quoted 11 lines

For radio stereo it needs still some v4l2 app and kradio and mplayer with v4l2 radio support are still the best candidates, but I'm not on latest on radio apps around currently.

Reception improvement is of course still the best key for all.

Thanks,
Hermann

Thanks for the answers and your further quesions, which I can answer here:
- I receive Radio and TV via cable, so the signal strength is ok (for stereo and rds)
- There are no frequency-filters so the tuner gets the whole bandwith
- In Windows with the original Terratec-SW everything (incl. RDS) works fine.

So I assume, there must be a problem in the driver in the area of radio.

Thanks for further help in advance.
Roland

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

#4 lore raw

Hi,

Am Donnerstag, den 12.11.2009, 21:35 +0100 schrieb Roland Egli:

Quoted 76 lines
Quoted 57 lines · hermann pitton

Hi,

Am Dienstag, den 10.11.2009, 15:50 +0100 schrieb Hans J. Koch:

Quoted 15 lines · Roland Egli
Quoted 7 lines

Hi all

I have the TV card "Terratec Cinergy 600 TV MK3" with SAA7134HL. The tuner is a Philips FM1216ME/H-3 and there is an additional RDS decoder SAA6588T.

Quoted 7 lines

For loading the module I use

$ modprobe saa7134 card=48 tuner=38

TV works fine, but I have a problem with the radio. The sound is very noisy, not stereo and there is as well no RDS reception (saa6588 module is loaded as well).

Quoted 9 lines

For RDS reception, you need a strong signal since the RDS carrier's level is well below the audio carrier level. Your only chance is to improve reception. What kind of antenna are you using? Are you sure it's connected to the _radio_ antenna jack and not the TV?

Thanks,
Hans

Hans, for what I know it makes no difference on that tuner, if radio comes in from the TV antenna connector or from the radio connector.

At least we don't have some dedicated separating RF input switch for that.

For example, the other way round, if you have a cable TV provider also providing radio, and radio freqs are not filtered from the TV input connected, radio will just work fine from the TV antenna connector and likely are all stereo. I can't tell anything for RDS.

If you now also connect that cheap rabbit ears antenna mostly coming with such cards, this might lead to overlapping frequencies noticed as too much noise on radio. Maybe we still miss something, but it is not in the tuner specs.

Me and one single other guy reported loud thrilling noise for radio if tuned into off on later driver revisions. I'm still not sure, if it is only caused by machine specific interferences, a network cable had some impact on it, but I saw/heard it later also on FMD hybrid devices on a different machine.

To connect the rabbit ears to the radio antenna connector will turn that annoying noise into normal static. On that FMD hybrid you usually will have the better radio reception from a roof mounted antenna for DVB-T and there is also no active RF input switching like we only saw it later on silicon hybrid devices.

Quoted 11 lines

For radio stereo it needs still some v4l2 app and kradio and mplayer with v4l2 radio support are still the best candidates, but I'm not on latest on radio apps around currently.

Reception improvement is of course still the best key for all.

Thanks,
Hermann

Thanks for the answers and your further quesions, which I can answer here:
- I receive Radio and TV via cable, so the signal strength is ok (for stereo and rds)
- There are no frequency-filters so the tuner gets the whole bandwith
- In Windows with the original Terratec-SW everything (incl. RDS) works fine.

Quoted 5 lines

So I assume, there must be a problem in the driver in the area of radio.

Thanks for further help in advance.
Roland

hm, Roland, radio sound is very noisy and not stereo.

To start from top and latest radio bug I do remember.

It is not _all_ only noise for radio with v4l1 apps and we don't deal with the bug described here you might eventually have fun with?

http://www.mail-archive.com/[email protected]/msg09814.html

Cheers,
Hermann

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list