Skip to contentSkip to conversation

sky2: Enable/disable WOL per hardware device

PATCH Applied Mike McCormack 2 participants 3 messages Jan 19, 2010 – Jan 23, 2010

Subsystems (2)
Networking Network drivers
lore
Share & tools
lore

Mike McCormack

author
#0 lore raw

PATCH 1/1 sky2: Enable/disable WOL per hardware device

Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip, not per port. On dual port cards, Y2_HW_WOL_ON should be enabled if either sky2 port has WOL enabled.

Found while reviewing code for a WOL regression, though this is probably not the cause of the regression.

Signed-off-by Mike McCormack <[email protected]>
---
 drivers/net/sky2.c |   29 ++++++++++++++++++++++-------
 1 files changed, 22 insertions(+), 7 deletions(-)
drivers/net/sky2.c +22 -7
index 4c06020..d86b7e8 100644
@@ -3238,6 +3238,27 @@ static inline u8 sky2_wol_supported(const struct sky2_hw *hw)
 	return sky2_is_copper(hw) ? (WAKE_PHY | WAKE_MAGIC) : 0;
 }
 
+static void sky2_hw_set_wol(struct sky2_hw *hw)
+{
+	int wol = 0;
+	int i;
+
+	for (i = 0; i < hw->ports; i++) {
+		struct net_device *dev = hw->dev[i];
+		struct sky2_port *sky2 = netdev_priv(dev);
+
+		if (sky2->wol)
+			wol = 1;
+	}
+
+	if (hw->chip_id == CHIP_ID_YUKON_EC_U ||
+	    hw->chip_id == CHIP_ID_YUKON_EX ||
+	    hw->chip_id == CHIP_ID_YUKON_FE_P)
+		sky2_write32(hw, B0_CTST, wol ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF);
+
+	device_set_wakeup_enable(&hw->pdev->dev, wol);
+}
+
 static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
 {
 	const struct sky2_port *sky2 = netdev_priv(dev);

@@ -3257,13 +3278,7 @@ static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
 
 	sky2->wol = wol->wolopts;
 
-	if (hw->chip_id == CHIP_ID_YUKON_EC_U ||
-	    hw->chip_id == CHIP_ID_YUKON_EX ||
-	    hw->chip_id == CHIP_ID_YUKON_FE_P)
-		sky2_write32(hw, B0_CTST, sky2->wol
-			     ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF);
-
-	device_set_wakeup_enable(&hw->pdev->dev, sky2->wol);
+	sky2_hw_set_wol(hw);
 
 	if (!netif_running(dev))
 		sky2_wol_init(sky2);
Signature · 1 line
1.5.6.5
maintainer
#1 lore raw

From: Mike McCormack <[email protected]>
Date: Tue, 19 Jan 2010 23:11:26 +0900

Quoted 8 lines

Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip, not per port. On dual port cards, Y2_HW_WOL_ON should be enabled if either sky2 port has WOL enabled.

Found while reviewing code for a WOL regression, though this is probably not the cause of the regression.

Signed-off-by Mike McCormack <[email protected]>

Stephen? ACK?

maintainer Applied
#2 lore raw
In reply to Mike McCormack

From: Mike McCormack <[email protected]>
Date: Tue, 19 Jan 2010 23:11:26 +0900

Quoted 8 lines

Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip, not per port. On dual port cards, Y2_HW_WOL_ON should be enabled if either sky2 port has WOL enabled.

Found while reviewing code for a WOL regression, though this is probably not the cause of the regression.

Signed-off-by Mike McCormack <[email protected]>

Applied, thanks Mike.