USB host on 83xx
I have two nearly identical boards, with very different behavior.
Older 8347 (PVR: 0x80830011)
New 8347 (PVR: 0x80830031)
I've tried a number of kernels (vintages) on both with wild results.
2.6.20 - Same kernel works on both(*)
2.6.28 - Kernel runs great on OLD, machine check on NEW
2.6.32.6 - Ditto
The problem occurs (only on the new silicon) during the USB host initialization. The root hub is found and initialized, then the EHCI subsystem is reset (to force it to find siblings on the bus). This results in a machine check at the point where the PHY is being reinitialized.
I've peppered the driver with messages - here's what I see:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
********** ehci_fsl_setup.272
********** ehci_fsl_setup.296
********** ehci_fsl_setup.299
********** ehci_fsl_reinit.257
********** mpc83xx_usb_setup.192
********** mpc83xx_usb_setup.207
********** mpc83xx_usb_setup.215
********** mpc83xx_usb_setup.220
********** mpc83xx_setup_phy.163
********** mpc83xx_setup_phy.180
********** mpc83xx_setup_phy.182
********** mpc83xx_usb_setup.238
********** mpc83xx_usb_setup.245
********** mpc83xx_usb_setup.249
********** mpc83xx_usb_setup.251
********** ehci_fsl_reinit.259
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
********** ehci_fsl_reinit.261
********** ehci_fsl_setup.301
fsl-ehci fsl-ehci.0: irq 39, io base 0xff022000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
********** ehci_hub_control.559 - req: 40966
********** ehci_hub_control.637
hub 1-0:1.0: 2 ports detected
********** ehci_hub_control.559 - req: 40960
********** ehci_hub_control.642
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Freescale On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.28 ehci_hcd
usb usb1: SerialNumber: fsl-ehci.0
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
********** ehci_fsl_setup.272
********** ehci_fsl_setup.296
********** ehci_fsl_setup.299
********** ehci_fsl_reinit.257
********** mpc83xx_usb_setup.192
********** mpc83xx_usb_setup.207
********** mpc83xx_usb_setup.215
********** mpc83xx_setup_phy.163
********** mpc83xx_setup_phy.180
MACHINE CHECK - so dead it can't even print the message!At this point, it should carry on like this:
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
********** ehci_hub_control.559 - req: 41728
********** ehci_hub_control.648
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: Product: USB2.0 Hub
********** ehci_hub_control.559 - req: 41728
********** ehci_hub_control.648You can see that it successfully found the connected external HUB.
Any ideas why this happens? This [basic] code used to work (2.6.20) on both platforms. I know that's a long time ago, but MACHINE CHECK??
(*) To get this platform to run 2.6.20, I had to patch the CPU tables to recognize it as 8347 (kernels of that vintage relied on the SVR to make choices, not PVR)
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Quoted 4 lines · Gary Thomas
I have two nearly identical boards, with very different behavior.
Older 8347 (PVR:
0x80830011)
New 8347 (PVR:0x80830031)
I lied (more precisely I was lied to and I passed it on - I've never seen these boards in person, just worked on them from thousands of miles away).
The boards have more than a rev difference:
OLD - 8347EA (SVR: 0x80540011, PVR: 0x80830011)
NEW - 8343E (SVR: 0x80570030, PVR: 0x80830031)
Could this have any bearing on the problems?
Quoted 96 lines
I've tried a number of kernels (vintages) on both with wild results.
2.6.20 - Same kernel works on
both(*)
2.6.28 - Kernel runs great on OLD, machine check on NEW 2.6.32.6 - DittoThe problem occurs (only on the new silicon) during the USB host initialization. The root hub is found and initialized, then the EHCI subsystem is reset (to force it to find siblings on the bus). This results in a machine check at the point where the PHY is being reinitialized.
I've peppered the driver with messages - here's what I see:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 ********** ehci_fsl_setup.272
********** ehci_fsl_setup.296
********** ehci_fsl_setup.299
********** ehci_fsl_reinit.257
********** mpc83xx_usb_setup.192
********** mpc83xx_usb_setup.207
********** mpc83xx_usb_setup.215
********** mpc83xx_usb_setup.220
********** mpc83xx_setup_phy.163
********** mpc83xx_setup_phy.180
********** mpc83xx_setup_phy.182
********** mpc83xx_usb_setup.238
********** mpc83xx_usb_setup.245
********** mpc83xx_usb_setup.249
********** mpc83xx_usb_setup.251
********** ehci_fsl_reinit.259
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
********** ehci_fsl_reinit.261
********** ehci_fsl_setup.301
fsl-ehci fsl-ehci.0: irq 39, io base0xff022000fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
********** ehci_hub_control.559 - req: 40966
********** ehci_hub_control.637
hub 1-0:1.0: 2 ports detected
********** ehci_hub_control.559 - req: 40960
********** ehci_hub_control.642
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Freescale On-Chip EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.28ehci_hcd
usb usb1: SerialNumber: fsl-ehci.0
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 ********** ehci_fsl_setup.272
********** ehci_fsl_setup.296
********** ehci_fsl_setup.299
********** ehci_fsl_reinit.257
********** mpc83xx_usb_setup.192
********** mpc83xx_usb_setup.207
********** mpc83xx_usb_setup.215
********** mpc83xx_setup_phy.163
********** mpc83xx_setup_phy.180
MACHINE CHECK - so dead it can't even print the message!At this point, it should carry on like this:
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
********** ehci_hub_control.559 - req: 41728
********** ehci_hub_control.648
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 usb 1-1: Product: USB2.0 Hub
********** ehci_hub_control.559 - req: 41728
********** ehci_hub_control.648You can see that it successfully found the connected external HUB.
Any ideas why this happens? This [basic] code used to work (2.6.20) on both platforms. I know that's a long time ago, but MACHINE CHECK??
(*) To get this platform to run 2.6.20, I had to patch the CPU tables to recognize it as 8347 (kernels of that vintage relied on the SVR to make choices, not PVR)
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Quoted 6 lines · Gary Thomas
Quoted 4 lines · Gary Thomas
I have two nearly identical boards, with very different behavior.
Older 8347 (PVR:
0x80830011)
New 8347 (PVR:0x80830031)
Quoted 7 lines
I lied (more precisely I was lied to and I passed it on - I've never seen these boards in person, just worked on them from thousands of miles away).
The boards have more than a rev difference:
OLD - 8347EA (SVR:0x80540011, PVR:0x80830011)
NEW - 8343E (SVR:0x80570030, PVR:0x80830031)
This turned out to be a powerup/strapping issue. This is now fixed and the SVR is 0x80550030 on the failing board. No change in behavior.
Does anyone have any ideas about this?
Quoted 100 lines
Could this have any bearing on the problems?
Quoted 96 lines
I've tried a number of kernels (vintages) on both with wild results.
2.6.20 - Same kernel works on
both(*)
2.6.28 - Kernel runs great on OLD, machine check on NEW 2.6.32.6 - DittoThe problem occurs (only on the new silicon) during the USB host initialization. The root hub is found and initialized, then the EHCI subsystem is reset (to force it to find siblings on the bus). This results in a machine check at the point where the PHY is being reinitialized.
I've peppered the driver with messages - here's what I see:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 ********** ehci_fsl_setup.272
********** ehci_fsl_setup.296
********** ehci_fsl_setup.299
********** ehci_fsl_reinit.257
********** mpc83xx_usb_setup.192
********** mpc83xx_usb_setup.207
********** mpc83xx_usb_setup.215
********** mpc83xx_usb_setup.220
********** mpc83xx_setup_phy.163
********** mpc83xx_setup_phy.180
********** mpc83xx_setup_phy.182
********** mpc83xx_usb_setup.238
********** mpc83xx_usb_setup.245
********** mpc83xx_usb_setup.249
********** mpc83xx_usb_setup.251
********** ehci_fsl_reinit.259
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
********** ehci_fsl_reinit.261
********** ehci_fsl_setup.301
fsl-ehci fsl-ehci.0: irq 39, io base0xff022000fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
********** ehci_hub_control.559 - req: 40966
********** ehci_hub_control.637
hub 1-0:1.0: 2 ports detected
********** ehci_hub_control.559 - req: 40960
********** ehci_hub_control.642
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Freescale On-Chip EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.28ehci_hcd
usb usb1: SerialNumber: fsl-ehci.0
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 ********** ehci_fsl_setup.272
********** ehci_fsl_setup.296
********** ehci_fsl_setup.299
********** ehci_fsl_reinit.257
********** mpc83xx_usb_setup.192
********** mpc83xx_usb_setup.207
********** mpc83xx_usb_setup.215
********** mpc83xx_setup_phy.163
********** mpc83xx_setup_phy.180
MACHINE CHECK - so dead it can't even print the message!At this point, it should carry on like this:
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
********** ehci_hub_control.559 - req: 41728
********** ehci_hub_control.648
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 usb 1-1: Product: USB2.0 Hub
********** ehci_hub_control.559 - req: 41728
********** ehci_hub_control.648You can see that it successfully found the connected external HUB.
Any ideas why this happens? This [basic] code used to work (2.6.20) on both platforms. I know that's a long time ago, but MACHINE CHECK??
(*) To get this platform to run 2.6.20, I had to patch the CPU tables to recognize it as 8347 (kernels of that vintage relied on the SVR to make choices, not PVR)
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Quoted 11 lines · Gary Thomas
Quoted 10 lines · Gary Thomas
Quoted 4 lines · Gary Thomas
I have two nearly identical boards, with very different behavior.
Older 8347 (PVR:
0x80830011)
New 8347 (PVR:0x80830031)I lied (more precisely I was lied to and I passed it on - I've never seen these boards in person, just worked on them from thousands of miles away).
Quoted 9 lines
Quoted 3 lines
The boards have more than a rev difference:
OLD - 8347EA (SVR:0x80540011, PVR:0x80830011)
NEW - 8343E (SVR:0x80570030, PVR:0x80830031)This turned out to be a powerup/strapping issue. This is now fixed and the SVR is
0x80550030on the failing board. No change in behavior.Does anyone have any ideas about this?
Even more data; it turns out that after the first write to the USB/DR port status/control register, the processor is dead :-( Using a BDI:
** Dump the USB/DR machine registers
asp8347>md 0xff023100ff023100 : 40000001 11000100 06000000 00000000 @............... ff023110 : 00000000 00000000 00000000 00000000 ................ ff023120 : 01000000 86010000 00000000 00000000 ................ ff023130 : 00000000 00000000 00000000 00000000 ................ ff023140 : 00000800 00000000 00000000 00000000 ................ ff023150 : 00000000 00000000 00000000 00000000 ................ ff023160 : 10100000 00000000 00000000 00000000 ................ ff023170 : 00000008 00000000 00000000 00000000 ................ ff023180 : 01000000 00000090 00000000 00000000 ................ ff023190 : 00000000 00000000 00000000 00000000 ................ ff0231a0 : 00000000 20100000 00000000 00000000 .... ........... ff0231b0 : 00000000 00000000 00000000 00000000 ................ ff0231c0 : 80008000 00000000 00000000 00000000 ................ ff0231d0 : 00000000 00000000 00000000 00000000 ................ ff0231e0 : 00000000 00000000 00000000 00000000 ................ ff0231f0 : 00000000 00000000 00000000 00000000 ................
** Write to the port status/control register
asp8347>mm 0xff023184 0x80
** Display the USB/DR registers
asp8347>md 0xff023100
# SAP: read access failed
This of course works fine on the 1.1 silicon.
Quoted 101 lines
Quoted 100 lines
Could this have any bearing on the problems?
Quoted 96 lines
I've tried a number of kernels (vintages) on both with wild results.
2.6.20 - Same kernel works on
both(*)
2.6.28 - Kernel runs great on OLD, machine check on NEW 2.6.32.6 - DittoThe problem occurs (only on the new silicon) during the USB host initialization. The root hub is found and initialized, then the EHCI subsystem is reset (to force it to find siblings on the bus). This results in a machine check at the point where the PHY is being reinitialized.
I've peppered the driver with messages - here's what I see:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 ********** ehci_fsl_setup.272
********** ehci_fsl_setup.296
********** ehci_fsl_setup.299
********** ehci_fsl_reinit.257
********** mpc83xx_usb_setup.192
********** mpc83xx_usb_setup.207
********** mpc83xx_usb_setup.215
********** mpc83xx_usb_setup.220
********** mpc83xx_setup_phy.163
********** mpc83xx_setup_phy.180
********** mpc83xx_setup_phy.182
********** mpc83xx_usb_setup.238
********** mpc83xx_usb_setup.245
********** mpc83xx_usb_setup.249
********** mpc83xx_usb_setup.251
********** ehci_fsl_reinit.259
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
********** ehci_fsl_reinit.261
********** ehci_fsl_setup.301
fsl-ehci fsl-ehci.0: irq 39, io base0xff022000fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
********** ehci_hub_control.559 - req: 40966
********** ehci_hub_control.637
hub 1-0:1.0: 2 ports detected
********** ehci_hub_control.559 - req: 40960
********** ehci_hub_control.642
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Freescale On-Chip EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.28ehci_hcd
usb usb1: SerialNumber: fsl-ehci.0
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 ********** ehci_fsl_setup.272
********** ehci_fsl_setup.296
********** ehci_fsl_setup.299
********** ehci_fsl_reinit.257
********** mpc83xx_usb_setup.192
********** mpc83xx_usb_setup.207
********** mpc83xx_usb_setup.215
********** mpc83xx_setup_phy.163
********** mpc83xx_setup_phy.180
MACHINE CHECK - so dead it can't even print the message!At this point, it should carry on like this:
********** ehci_hub_control.559 - req: 8963
********** ehci_hub_control.805
********** ehci_hub_control.559 - req: 41728
********** ehci_hub_control.648
********** ehci_hub_control.559 - req: 8961
********** ehci_hub_control.574
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 usb 1-1: Product: USB2.0 Hub
********** ehci_hub_control.559 - req: 41728
********** ehci_hub_control.648You can see that it successfully found the connected external HUB.
Any ideas why this happens? This [basic] code used to work (2.6.20) on both platforms. I know that's a long time ago, but MACHINE CHECK??
(*) To get this platform to run 2.6.20, I had to patch the CPU tables to recognize it as 8347 (kernels of that vintage relied on the SVR to make choices, not PVR)
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------