Skip to contentSkip to conversation

Errors during a simple mount storm test

DISCUSSION Shehjar Tikoo 2 participants 3 messages Feb 4, 2010 1 message not in the archive

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

Hi All

The shell command below is probably not applicable to all real world setups but I wanted to check it out nonetheless. The problem is with the following command that is supposed run a mount-umount loop:

$ while [ true ]; do echo sending; mount localhost:/test -o noacl,nolock,tcp,mountproto=tcp /mnt;umount  /mnt; done

For the first hundred iterations, it works fine but then starts spewing errors with the mount command failing. For eg. the output looks like below:

sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted

Any ideas why the mount sequence stops abruptly? There dont seem to be any relevant messages in the dmesg output either.

The client and server are on the same machine:
Linux indus 2.6.31-17-generic Ubuntu SMP x86_64 GNU/Linux

I have verified through wireshark that the server is not receiving any mount requests once the mount command start failing. Instead there are only successful GETPORT requests for the MOUNTv3 program.

Thanks
-Shehjar

A message that is not in the archive (sent off-list or not yet received): [email protected]

#2 lore raw
Quoted 42 lines · Shehjar Tikoo

Hi All

The shell command below is probably not applicable to all real world setups but I wanted to check it out nonetheless. The problem is with the following command that is supposed run a mount-umount loop:

$ while [ true ]; do echo sending; mount localhost:/test -o 
noacl,nolock,tcp,mountproto=tcp /mnt;umount  /mnt; done

For the first hundred iterations, it works fine but then starts spewing errors with the mount command failing. For eg. the output looks like below:

sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted

Any ideas why the mount sequence stops abruptly? There dont seem to be any relevant messages in the dmesg output either.

Quoted 7 lines

The client and server are on the same machine:
Linux indus 2.6.31-17-generic Ubuntu SMP x86_64 GNU/Linux

I have verified through wireshark that the server is not receiving any mount requests once the mount command start failing. Instead there are only successful GETPORT requests for the MOUNTv3 program.

"netstat -t" will probably show you that all your free ports in the range 0-1023 are now in the TIME_WAIT state. This again means that you have to wait a couple of minutes for the TIME_WAITs to expire before you can try again.

So basically, it is a case of your test being flawed.

Trond

#3 lore raw
Quoted 50 lines · Trond Myklebust
Quoted 41 lines · Shehjar Tikoo

Hi All

The shell command below is probably not applicable to all real world setups but I wanted to check it out nonetheless. The problem is with the following command that is supposed run a mount-umount loop:

$ while [ true ]; do echo sending; mount localhost:/test -o noacl,nolock,tcp,mountproto=tcp /mnt;umount  /mnt; done

For the first hundred iterations, it works fine but then starts spewing errors with the mount command failing. For eg. the output looks like below:

sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted
sending
mount.nfs: mount system call failed
umount: /mnt: not mounted

Any ideas why the mount sequence stops abruptly? There dont seem to be any relevant messages in the dmesg output either.

Quoted 7 lines

The client and server are on the same machine:
Linux indus 2.6.31-17-generic Ubuntu SMP x86_64 GNU/Linux

I have verified through wireshark that the server is not receiving any mount requests once the mount command start failing. Instead there are only successful GETPORT requests for the MOUNTv3 program.

Quoted 6 lines

"netstat -t" will probably show you that all your free ports in the range 0-1023 are now in the TIME_WAIT state. This again means that you have to wait a couple of minutes for the TIME_WAITs to expire before you can try again.

So basically, it is a case of your test being flawed.

Thanks!
I'll to resort to using noresvport in that case.

-Shehjar

Quoted 3 lines

Trond