Skip to contentSkip to conversation

How to optimise encrypted filesystems on an SSD?

dm-crypt mark 2 participants 2 messages Feb 5, 2010 – Feb 6, 2010

lore
Share & tools
lore

mark

author
#0 lore raw

Hi there.

For a while I've been using LUKS/dm-crypt with LVM2 to secure hard drives in laptops and servers. Recently I've moved one of my filesystems onto a solid-state drive (Intel X25-M-G2 80GB with latest firmware).

There are some excellent instructions here
http://thunk.org/tytso/blog/2009/02/20/aligning-filesystems-to-an-ssds-erase-block-size/
on how to align ext4 and LVM to the erase block size of the SSD. However I've not been able to find a recipe for optimising an encrypted filesystem in the same way.

A typical usage case for me would be this, from following defaults for encrypted lvm on the Debian installer:

/dev/sda1 79GB crypt-luks
/dev/mapper/sda1_crypt holds PV for LVM2
PV has a VG with two LVs, 4GB swap and the rest for ext4 /
/dev/sda5 256MB ext2 /boot

Could anyone explain how I might go about aligning/optimising this, or point me to some instructions? Am I better putting lvm over luks or luks over lvm? Or something entirely different?

Thanks in advance,
Mark

#1 lore raw
Quoted 6 lines · mark

For a while I've been using LUKS/dm-crypt with LVM2 to secure hard drives in laptops and servers. Recently I've moved one of my filesystems onto a solid-state drive (Intel X25-M-G2 80GB with latest firmware).

There are some excellent instructions here
http://thunk.org/tytso/blog/2009/02/20/aligning-filesystems-to-an-ssds-erase-block-size/

Beware - that page is completely obsolete regarding lvm2 now! Recent version have much more better support for data alignment (with new kernels it should be automatic)

Quoted 7 lines

on how to align ext4 and LVM to the erase block size of the SSD. However I've not been able to find a recipe for optimising an encrypted filesystem in the same way.

A typical usage case for me would be this, from following defaults for encrypted lvm on the Debian installer:

Quoted 8 lines

/dev/sda1 79GB crypt-luks
/dev/mapper/sda1_crypt holds PV for LVM2
PV has a VG with two LVs, 4GB swap and the rest for ext4 /
/dev/sda5 256MB ext2 /boot

Could anyone explain how I might go about aligning/optimising this, or point me to some instructions? Am I better putting lvm over luks or luks over lvm? Or something entirely different?

Just in short:
(cryptsetup will get support for automatic alignment according to kernel exported device parameters soon, so all this will be automatic)

- the underlying device must be aligned
(if using partitions, be sure you have start of partition aligned, better use "fdisk -u" to calculate in sectors.
If not sure, align to 1M or even 4M offset, this will always fit:-) (fdisk from latest util-linux-ng should support automatic alignment)

- be sure that lvm2 PV metadata (data start) is always aligned (see pvcreate --dataalignment parameter)
(latest lvm2 already have support for automatic data alignment if kernel exports proper alignment data)

- for cryptetup/LUKS - use "--align-payload" parameter (default is alignment to 4k boundary, not enough for SSD). Note that parameter is in 512 bytes sectors!

e.g. you want to align to 4MB boundary ( = 8192 * 512 bytes), use

cryptsetup luksFormat --align-payload=8192 ...

verify with cryptsetup luksDump (see Payload offset)

(I usually set lvm2 extent size to 4MB and aling LUKS the same, so the LUKS header takes exactly one extent.)

- and finally, you should optimize FS above that device stack

(From the kernel point of view, there is no difference
if you put lvm2 over LUKS or vice versa - both should work the same. Just configuration is different, I have some old slides describing activation of volumes here http://mbroz.fedorapeople.org/talks/LinuxAlt2008-eng/ )

Milan