da830evm: Add support for TI EMAC
PATCH 1/1 da830evm: Add support for TI EMAC
Adds support for ethernet networking on the da830evm platform.
This platform uses an SoC EMAC interface and a 3 port ethernet switch as a PHY with an RMII interface. The PHY also has a i2c interface for configuring the switch functions.
--- board/davinci/da830evm/da830evm.c | 64 +++++++++++++++++++++++++++++- include/asm-arm/arch-davinci/emac_defs.h | 1 + include/configs/da830evm.h | 1 + 3 files changed, 64 insertions(+), 2 deletions(-)
board/davinci/da830evm/da830evm.c +62 -2
@@ -34,6 +34,8 @@#include <common.h> #include <i2c.h> +#include <net.h> +#include <netdev.h> #include <asm/arch/hardware.h> #include <asm/arch/emif_defs.h> #include <asm/io.h>
@@ -69,6 +71,20 @@ static const struct pinmux_config emifa_nand_pins[] = { { pinmux[18], 1, 5 }, }; +/* EMAC PHY interface pins */ +static const struct pinmux_config emac_pins[] = { + { pinmux[9 ],0 ,5 }, + { pinmux[10 ],2 ,1 }, + { pinmux[10 ],2 ,2 }, + { pinmux[10 ],2 ,3 }, + { pinmux[10 ],2 ,4 }, + { pinmux[10 ],2 ,5 }, + { pinmux[10 ],2 ,6 }, + { pinmux[10 ],2 ,7 }, + { pinmux[11 ],2 ,0 }, + { pinmux[11 ],2 ,1 }, +}; +/* UART pin muxer settings */ static const struct pinmux_config uart_pins[] = { { pinmux[8], 2, 7 },
@@ -77,8 +93,8 @@ static const struct pinmux_config uart_pins[] = {/* I2C pin muxer settings */ static const struct pinmux_config i2c_pins[] = { - { pinmux[9 ],2 ,3 }, - { pinmux[9 ],2 ,4 } + { pinmux[8 ],2 ,3 }, + { pinmux[8 ],2 ,4 } };/* USB0_DRVVBUS pin muxer settings */
@@ -98,6 +114,9 @@ static const struct pinmux_resource pinmuxes[] = {#ifdef CONFIG_USE_NAND PINMUX_ITEM(emifa_nand_pins),#endif +#if defined(CONFIG_DRIVER_TI_EMAC ) + PINMUX_ITEM(emac_pins), +#endif };int board_init (void )
@@ -169,3 +188,44 @@ int board_init(void)return (0 ); } + +#if defined(CONFIG_DRIVER_TI_EMAC ) + +#define PHY_SW_I2C_ADDR 0x5f/* Address of PHY on i2c bus */ + +/* +* Initializes on-board ethernet controllers. +*/ +int board_eth_init (bd_t *bis) +{ +u_int8_t mac_addr[6 ]; +u_int8_t switch_start_cmd[2 ] = {0x01 ,0x23 }; + +/* Read Ethernet MAC address from EEPROM */ +if (dvevm_read_mac_address (mac_addr)) +/* set address env if not already set */ +dv_configure_mac_address (mac_addr); + +/* read the address back from env */ +if (!eth_getenv_enetaddr ("ethaddr" , mac_addr)) +return -1 ; + +/* provide the resulting addr to the driver */ +davinci_eth_set_mac_addr (mac_addr); + +/* enable the Ethernet switch in the 3 port PHY */ +if (i2c_write (PHY_SW_I2C_ADDR ,0 ,0 , + switch_start_cmd,sizeof (switch_start_cmd))) { +printf ("Ethernet switch start failed!\n" ); +return -1 ; + } + +/* finally, initialise the driver */ +if (!davinci_emac_initialize ()) { +printf ("Error: Ethernet init failed!\n" ); +return -1 ; + } + +return 0 ; +} +#endif /* CONFIG_DRIVER_TI_EMAC */
include/asm-arm/arch-davinci/emac_defs.h +1 -0
@@ -316,6 +316,7 @@ typedef struct {int davinci_eth_phy_read (u_int8_t phy_addr,u_int8_t reg_num,u_int16_t *data);int davinci_eth_phy_write (u_int8_t phy_addr,u_int8_t reg_num,u_int16_t data); +void davinci_eth_set_mac_addr (const u_int8_t *addr); typedef struct {
include/configs/da830evm.h +1 -0
@@ -27,6 +27,7 @@/* * Board */ +#define CONFIG_DRIVER_TI_EMAC /* * SoC Configuration
Signature · 1 line
1.6.3.3
PATCH 1/1 da830evm: Add support for TI EMAC
Quoted 7 lines · Nick Thompson
Adds support for ethernet networking on the da830evm platform.
This platform uses an SoC EMAC interface and a 3 port ethernet switch as a PHY with an RMII interface. The PHY also has a i2c interface for configuring the switch functions.
Signed-off-by Nick Thompson <[email protected]>
This patch adds a new warning - sorry missed that during testing
A V2 patch is on the way
Paulraj
PATCH 1/1 da830evm: Add support for TI EMAC
In reply to Nick ThompsonQuoted 8 lines
Adds support for ethernet networking on the da830evm platform.
This platform uses an SoC EMAC interface and a 3 port ethernet switch as a PHY with an RMII interface. The PHY also has a i2c interface for configuring the switch functions.
Quoted 7 lines
Signed-off-by Nick Thompson <[email protected]>--- board/davinci/da830evm/da830evm.c | 64 +++++++++++++++++++++++++++++- include/asm-arm/arch-davinci/emac_defs.h | 1 + include/configs/da830evm.h | 1 + 3 files changed, 64 insertions(+), 2 deletions(-)
Pushed to u-boot-ti.
I verified that the EMAC driver worked fine on the DM365.
Thanks,
Sandeep