Skip to contentSkip to conversation

I can't make forwarding

DISCUSSION Patrick Chemla 3 participants 5 messages Feb 16, 2010 – Mar 4, 2010

lore
Share & tools
lore
#0 lore raw

Hi,

I have problems to setup a NAT router using iptables.

My NAT Router is running Fedora 11.

I have 2 interfaces, eth0 10.0.0.1 is internal, eth1 172.25.2.2 is external.

I have 10 external public addresses coming to the interface eth1 that I want to forward to 10 internal computers on eth0.

When I try to ping or access an external web server from the NAT server itself, it works very fine. I see on the remote server the external address of the NAT router itself.
When I try to ping or wget an external web server from an internal 10.0.0.151 computer, using TCPDUMP both on the foreign server interface and on the eth1 of the NAT router, I see that packets reach the external server with the right IP 192.114.84.144, I see that the external server send back something, but I can't get it back on the eth1 tcpdump.

Here is my iptables:
============
iptables -n -L -v
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source
destination
1664 208K ACCEPT all -- * * 0.0.0.0/0
0.0.0.0/0 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT icmp -- * *
0.0.0.0/0 0.0.0.0/0
0 0 ACCEPT all -- lo *
0.0.0.0/0 0.0.0.0/0
0 0 ACCEPT tcp -- * *
0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22

Chain FORWARD (policy ACCEPT 3499 packets, 213K bytes)
pkts bytes target prot opt in out source
destination
0 0 ACCEPT all -- eth0 eth1
10.0.0.151 192.114.84.144 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT all -- eth1 eth0
192.114.84.144 10.0.0.151 state NEW,RELATED,ESTABLISHED

Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source
destination
466 71467 ACCEPT all -- * *
0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT icmp -- * *
0.0.0.0/0 0.0.0.0/0

Here is my NAT table:
=============
iptables -n -t nat -L -v
Chain PREROUTING (policy ACCEPT 915 packets, 129K bytes)
pkts bytes target prot opt in out source
destination
0 0 DNAT tcp -- eth1 *
192.114.84.144 0.0.0.0/0 to:10.0.0.151

Chain POSTROUTING (policy ACCEPT 75 packets, 6372 bytes)
pkts bytes target prot opt in out source
destination
16 960 SNAT all -- * eth1
10.0.0.151 0.0.0.0/0 to:192.114.84.144

Chain OUTPUT (policy ACCEPT 36 packets, 3998 bytes)
pkts bytes target prot opt in out source
destination

I think I ACCEPT and FORWARD all, I have both SNAT and DNAT, but I missed something.

Help will be welcome.

Patrick

#1 lore raw

Hi,

I tried more and doing this I can access to internet from a computer in the local network:
iptables --flush
iptables --table nat --flush
iptables --delete-chain
iptables --table nat --delete-chain
iptables --table nat --append POSTROUTING --out-interface eth1 -j MASQUERADE iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE

But the computer is viewed with the NAT router external local IP.

I need to have internal computers viewed with a different IP external address.

Patrick

Quoted 76 lines · Patrick Chemla

Hi,

I have problems to setup a NAT router using iptables.

My NAT Router is running Fedora 11.

I have 2 interfaces, eth0 10.0.0.1 is internal, eth1 172.25.2.2 is external.

I have 10 external public addresses coming to the interface eth1 that I want to forward to 10 internal computers on eth0.

When I try to ping or access an external web server from the NAT server itself, it works very fine. I see on the remote server the external address of the NAT router itself.
When I try to ping or wget an external web server from an internal 10.0.0.151 computer, using TCPDUMP both on the foreign server interface and on the eth1 of the NAT router, I see that packets reach the external server with the right IP 192.114.84.144, I see that the external server send back something, but I can't get it back on the eth1 tcpdump.

Here is my iptables:
============
iptables -n -L -v
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source
destination
1664 208K ACCEPT all -- * *
0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT icmp -- * *
0.0.0.0/0 0.0.0.0/0
0 0 ACCEPT all -- lo *
0.0.0.0/0 0.0.0.0/0
0 0 ACCEPT tcp -- * *
0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22

Chain FORWARD (policy ACCEPT 3499 packets, 213K bytes)
pkts bytes target prot opt in out
source destination
0 0 ACCEPT all -- eth0 eth1
10.0.0.151 192.114.84.144 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT all -- eth1 eth0
192.114.84.144 10.0.0.151 state NEW,RELATED,ESTABLISHED

Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source
destination
466 71467 ACCEPT all -- * *
0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT icmp -- * *
0.0.0.0/0 0.0.0.0/0

Here is my NAT table:
=============
iptables -n -t nat -L -v
Chain PREROUTING (policy ACCEPT 915 packets, 129K bytes)
pkts bytes target prot opt in out source
destination
0 0 DNAT tcp -- eth1 *
192.114.84.144 0.0.0.0/0 to:10.0.0.151

Chain POSTROUTING (policy ACCEPT 75 packets, 6372 bytes)
pkts bytes target prot opt in out source
destination
16 960 SNAT all -- * eth1
10.0.0.151 0.0.0.0/0 to:192.114.84.144

Chain OUTPUT (policy ACCEPT 36 packets, 3998 bytes)
pkts bytes target prot opt in out source
destination

I think I ACCEPT and FORWARD all, I have both SNAT and DNAT, but I missed something.

Help will be welcome.

Patrick

Signature · 3 lines
To unsubscribe from this list: send the line "unsubscribe netfilter" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#2 lore raw
In reply to Patrick Chemla
Quoted 45 lines · On 16.02.2010 12:34, [email protected] wrote:

Hi,

I have problems to setup a NAT router using iptables.

My NAT Router is running Fedora 11.

I have 2 interfaces, eth0 10.0.0.1 is internal, eth1 172.25.2.2 is external.

I have 10 external public addresses coming to the interface eth1 that I want to forward to 10 internal computers on eth0.

When I try to ping or access an external web server from the NAT server itself, it works very fine. I see on the remote server the external address of the NAT router itself.
When I try to ping or wget an external web server from an internal 10.0.0.151 computer, using TCPDUMP both on the foreign server interface and on the eth1 of the NAT router, I see that packets reach the external server with the right IP 192.114.84.144, I see that the external server send back something, but I can't get it back on the eth1 tcpdump.

Here is my iptables:
============
iptables -n -L -v
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source
destination
1664 208K ACCEPT all -- * * 0.0.0.0/0
0.0.0.0/0 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT icmp -- * *
0.0.0.0/0 0.0.0.0/0
0 0 ACCEPT all -- lo *
0.0.0.0/0 0.0.0.0/0
0 0 ACCEPT tcp -- * *
0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22

Chain FORWARD (policy ACCEPT 3499 packets, 213K bytes)
pkts bytes target prot opt in out source
destination
0 0 ACCEPT all -- eth0 eth1
10.0.0.151 192.114.84.144 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT all -- eth1 eth0
192.114.84.144 10.0.0.151 state NEW,RELATED,ESTABLISHED

Quoted 7 lines

Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source
destination
466 71467 ACCEPT all -- * * 0.0.0.0/0
0.0.0.0/0 state NEW,RELATED,ESTABLISHED
0 0 ACCEPT icmp -- * *
0.0.0.0/0 0.0.0.0/0

Why have all the ACCEPT rules, if the policy of all chains is ACCEPT? Use at least a DROP policy in INPUT and FORWARD chain.

EXT_IF=eth1
INT_IF=eth0
INT_IP01=10.0.0.151

iptables -A FORWARD -o $INT_IF -d $INT_IP01 -m state ... -p ... -j ACCEPT iptables -A FORWARD -i $INT_IF -s $INT_IP ... -j ACCEPT

Quoted 21 lines

Here is my NAT table:
=============
iptables -n -t nat -L -v
Chain PREROUTING (policy ACCEPT 915 packets, 129K bytes)
pkts bytes target prot opt in out source
destination
0 0 DNAT tcp -- eth1 *
192.114.84.144 0.0.0.0/0 to:10.0.0.151

Chain POSTROUTING (policy ACCEPT 75 packets, 6372 bytes)
pkts bytes target prot opt in out source
destination
16 960 SNAT all -- * eth1
10.0.0.151 0.0.0.0/0 to:192.114.84.144

Chain OUTPUT (policy ACCEPT 36 packets, 3998 bytes)
pkts bytes target prot opt in out source
destination

Quoted 6 lines

I think I ACCEPT and FORWARD all, I have both SNAT and DNAT, but I missed something.

Help will be welcome.

Patrick

ok, lets work this out:

goal 1: I want a request coming from the internet - towards a specific ip of the external interface of the gateway, to be redirected to a certain ip inside my internal network.

EXT_IF=eth1
EXT_IP01=192.114.84.144
INT_IP01=10.0.0.151

iptables -t nat -A PREROUTING -i $EXT_IF -d $EXT_IP01 -j DNAT --to-destination $INT_IP01

This will map external request to the internal server, traffic coming back will re-translated by itself.

Repeat for every external/internal IP pair...

goal 2: All traffic originating from a certain internal ip - should leave the external interface with a certain ip.

iptables -t nat -A POSTROUTING -o $EXT_IF -s $INT_IP01 -j SNAT --to-source $EXT_IP01

Repeat for every internal/external IP pair...

Writing all those stuff in the nat table, one might prefer assigning the external IPs to the servers and route the traffic through.

Best regards

Mart

#3 lore raw

Multiple IPs to 2 interfaces problem with default route

Hi,

I have set up a Fedora 11 NAT server to NAT outgoing traffic to 2 interfaces to 2 ISPs.

My internal interface is eth0, the 2 external interfaces are eth1 for ISP1 and eth2 for ISP2, each one with a pool of IP addresses.

I wrote a script who create for each internal server the corresponding NAT fonction :

interface= outgoing interface for the wanted ISP
public_ip= public IP address affected to this server on the ISP network server_ip= internal server local ip address

/sbin/iptables -t nat -A PREROUTING -p tcp -i $interface -s $public_ip/32 -j DNAT --to-destination $server_ip /sbin/iptables -t nat -A POSTROUTING -s $server_ip/32 -j SNAT -o $interface --to-source $public_ip

It works very fine with one interface, but when I try to activate the second interface, I think I get a problem with the default route.

When I started the interfaces, eth1 got a public IP and a default gateway. This default gateway is the default gateway for all the server. eth2 has his own public IP, own gateway.

I tried to remove the default gateway, thinking the route will be according to the NAT setup, but no more packet can get out of the server.

But I need to split packets to interfaces eth1 and eth2 according to the public IP of the internal server, not according to a default route always pointing to eth1.

How can I set up these routes?

Patrick

#4 lore raw

Re: Multiple IPs to 2 interfaces problem with default route

Quoted 10 lines · Patrick Chemla

I have set up a Fedora 11 NAT server to NAT outgoing traffic to 2 interfaces to 2 ISPs.

It works very fine with one interface, but when I try to activate the second interface, I think I get a problem with the default route.

When I started the interfaces, eth1 got a public IP and a default gateway. This default gateway is the default gateway for all the server. eth2 has his own public IP, own gateway.

Quoted 8 lines

I tried to remove the default gateway, thinking the route will be according to the NAT setup, but no more packet can get out of the server.

But I need to split packets to interfaces eth1 and eth2 according to the public IP of the internal server, not according to a default route always pointing to eth1.

How can I set up these routes?

Look for "source based routing" or "policy routing" - this hasn't got much to do with NAT or netfilter.

Something like
http://lartc.org/howto/lartc.rpdb.html
may help you.

c'ya
sven-haegar

Signature · 2 lines
Three may keep a secret, if two of them are dead.
- Ben F.