Elgato EyeTV DTT deluxe v2 - i2c enumeration failed
Hi, I recently purchased the Elgato EyeTV DTT deluxe v2 stick. I am running Ubuntu 8.10 with Linux 2.6.28-15-generic. I installed v4l-dvb from mercurial with a slight change of linux/drivers/media/dvb/dvb-usb/dvb-usb-ids.h to account for the USB ID of the device (#define USB_PID_ELGATO_EYETV_DTT_Dlx 0x002c). After insertion the stick is recognized, however no frontend is activated since the i2c enumeration failed. This might be related to a missing udev rule. Any support is appreciated. This is the corresponding part from dmesg
kernel: [24106.302688] usb 2-1: new high speed USB device using ehci_hcd and address 45
kernel: [24106.459222] usb 2-1: configuration #1 chosen from 1 choice
kernel: [24106.459730] dvb-usb: found a 'Elgato EyeTV Dtt Dlx PD378S' in cold state, will try to load a firmware
kernel: [24106.459738] usb 2-1: firmware: requesting dvb-usb-dib0700-1.20.fw
kernel: [24106.523808] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'
kernel: [24106.733953] dib0700: firmware started successfully.
kernel: [24107.244517] dvb-usb: found a 'Elgato EyeTV Dtt Dlx PD378S' in warm state.
kernel: [24107.244631] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
kernel: [24107.244862] DVB: registering new adapter (Elgato EyeTV Dtt Dlx PD378S)
kernel: [24107.327206] dib0700: stk7070p_frontend_attach: dib7000p_i2c_enumeration failed. Cannot continue
kernel: [24107.327211]
kernel: [24107.327216] dvb-usb: no frontend was attached by 'Elgato EyeTV Dtt Dlx PD378S'
kernel: [24107.327223] dvb-usb: Elgato EyeTV Dtt Dlx PD378S successfully initialized and connected.
kernel: [24107.327703] dib0700: ir protocol setup failed
kernel: [24130.411288] dvb-usb: Elgato EyeTV Dtt Dlx PD378S successfully deinitialized and disconnected.
Quoted 7 lines · On Wednesday 24 February 2010 21:23:45 Bringfried Stecklum wrote:
Hi, I recently purchased the Elgato EyeTV DTT deluxe v2 stick. I am running Ubuntu 8.10 with Linux 2.6.28-15-generic. I installed v4l-dvb from
mercurial with a slight change oflinux/drivers/media/dvb/dvb-usb/dvb-usb-ids.hto account for the USB ID of the device (#defineUSB_PID_ELGATO_EYETV_DTT_Dlx0x002c). After insertion the stick is recognized, however no frontend is activated since the i2c enumeration failed. This might be related to a missing udev rule.
Most likely Elgato has changed the USB ID of their product, because it is not the same product. In general (I'd say 50% of the cases) changing the USB ID is not the right solution to get the hardware work.
If you can, open the stick to see on which hardware the device is based on, or search the internet to find out.
If you're lucky another minor quirk in this or another driver is sufficient to make it work.
Signature · 2 lines
Patrick Boettcher - KernelLabs http://www.kernellabs.com/