Chronic USB disconnect events for Pinnacle Dazzle DVC 100 video capture device
I have a Pinnacle Dazzle DVC 100 USB video capture device hooked up to a security camera capturing video 24/7. A few times a month, my kernel suddenly decides that the USB device was disconnected and reconnected, resulting in the device getting a new number and causing my recording software to stop recording until I restart it with the new device number. Here is an example of the dmesg output when it happens:
[1126917.418424] usb 2-8: USB disconnect, address 3 [1126917.444413] em28xx #0: disconnecting em28xx #0 video [1126917.445563] em28xx #0: device /dev/video4 is open! Deregistration and memory deallocation are deferred on close. [1126917.701033] usb 2-8: new high speed USB device using ehci_hcd and address 4 [1126917.846251] usb 2-8: configuration #1 chosen from 1 choice [1126917.847514] em28xx new video device (2304:021a): interface 0, class 255 [1126917.847552] em28xx Has usb audio class [1126917.847554] em28xx #1: Alternate settings: 8 [1126917.847556] em28xx #1: Alternate setting 0, max size= 0 [1126917.847557] em28xx #1: Alternate setting 1, max size= 1024 [1126917.847559] em28xx #1: Alternate setting 2, max size= 1448 [1126917.847605] em28xx #1: Alternate setting 3, max size= 2048 [1126917.847607] em28xx #1: Alternate setting 4, max size= 2304 [1126917.847608] em28xx #1: Alternate setting 5, max size= 2580 [1126917.847610] em28xx #1: Alternate setting 6, max size= 2892 [1126917.847611] em28xx #1: Alternate setting 7, max size= 3072 [1126917.849350] em28xx #1: em28xx chip ID = 18 [1126918.507903] saa7115' 7-0025: saa7113 found (1f7113d0e100000) @ 0x4a (em28xx #1) [1126919.323999] em28xx #1: i2c eeprom 00: 1a eb 67 95 04 23 1a 02 12 00 11 03 98 10 6a 2e [1126919.324013] em28xx #1: i2c eeprom 10: 00 00 06 57 4e 00 00 00 60 00 00 00 02 00 00 00 [1126919.324022] em28xx #1: i2c eeprom 20: 02 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 [1126919.324028] em28xx #1: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 01 00 00 00 00 00 00 [1126919.324033] em28xx #1: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [1126919.324039] em28xx #1: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [1126919.324046] em28xx #1: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 2e 03 50 00 69 00 [1126919.324058] em28xx #1: i2c eeprom 70: 6e 00 6e 00 61 00 63 00 6c 00 65 00 20 00 53 00 [1126919.324070] em28xx #1: i2c eeprom 80: 79 00 73 00 74 00 65 00 6d 00 73 00 20 00 47 00 [1126919.324083] em28xx #1: i2c eeprom 90: 6d 00 62 00 48 00 00 00 10 03 44 00 56 00 43 00 [1126919.324096] em28xx #1: i2c eeprom a0: 31 00 30 00 30 00 00 00 32 00 30 00 33 00 35 00 [1126919.324108] em28xx #1: i2c eeprom b0: 36 00 30 00 37 00 35 00 31 00 33 00 34 00 31 00 [1126919.324121] em28xx #1: i2c eeprom c0: 30 00 32 00 30 00 30 00 30 00 31 00 00 00 32 00 [1126919.324134] em28xx #1: i2c eeprom d0: 33 00 31 00 32 00 33 00 00 00 00 00 00 00 00 00 [1126919.324147] em28xx #1: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [1126919.324159] em28xx #1: i2c eeprom f0: 00 00 00 00 00 00 00 00 69 4d 74 05 ad 62 5d 0e [1126919.324173] EEPROM ID= 0x9567eb1a, hash = 0x20810e85 [1126919.324175] Vendor/Product ID= 2304:021a [1126919.324177] AC97 audio (5 sample rates) [1126919.324179] 300mA max power [1126919.324182] Table at 0x06, strings=0x1098, 0x2e6a, 0x0000 [1126919.917596] em28xx #1: V4L2 device registered as /dev/video5 and /dev/vbi5 [1126919.917606] em28xx #1: Found Pinnacle Dazzle DVC 90/DVC 100
This machine is running Ubuntu 8.10 with kernel 2.6.27-17-generic. Is this a known problem for this particular capture device or a potential driver issue? Should I be bugging the USB people instead of this list? Any ideas would be appreciated.
thanks,
-Ben Swartzlander
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
Quoted 6 lines · Ben Swartzlander
I have a Pinnacle Dazzle DVC 100 USB video capture device hooked up to a security camera capturing video 24/7. A few times a month, my kernel suddenly decides that the USB device was disconnected and reconnected, resulting in the device getting a new number and causing my recording software to stop recording until I restart it with the new device number. Here is an example of the dmesg output when it happens:
The USB host controller might be going to sleep if the PC's suspend/resume kicked in. Or, is there a USB hub involved which might have been power cycled? It's pretty hard to figure out *why* the hardware decided to disconnect the USB device.
The reason the device gets a new device number is because it is still in use when the disconnect occurs. If the application were not running at the time of the disconnect event, you would get the same device number.
Also, it's probably worth mentioning that these sorts of devices are not really designed for capture 24/7, so it might be overheating or some bug in the hardware.
Devin
Signature · 7 lines
Devin J. Heitmueller - Kernel Labs http://www.kernellabs.com -- video4linux-list mailing list Unsubscribe mailto:[email protected]?subject=unsubscribe https://www.redhat.com/mailman/listinfo/video4linux-list
Quoted 20 lines · Devin Heitmueller
Quoted 7 lines · Ben Swartzlander
I have a Pinnacle Dazzle DVC 100 USB video capture device hooked up to a security camera capturing video 24/7. A few times a month, my kernel suddenly decides that the USB device was disconnected and reconnected, resulting in the device getting a new number and causing my recording software to stop recording until I restart it with the new device number. Here is an example of the dmesg output when it happens:
The USB host controller might be going to sleep if the PC's suspend/resume kicked in. Or, is there a USB hub involved which might have been power cycled? It's pretty hard to figure out *why* the hardware decided to disconnect the USB device.
The reason the device gets a new device number is because it is still in use when the disconnect occurs. If the application were not running at the time of the disconnect event, you would get the same device number.
Quoted 7 lines
Also, it's probably worth mentioning that these sorts of devices are not really designed for capture 24/7, so it might be overheating or some bug in the hardware.
Devin
try to update to ubuntu 9.04 from 8.10 this solve my problem
but I think I need to modprobe blacklist any usb keu that need the ehci (usb2)
or it kicks my em2860 vstream to usb1 hub
8.10 = my ehci was loaded after ohci
9.04 = ehci loaded before all the time
--
This message has been verified by LastSpam (http://www.lastspam.com) eMail security service, provided by SoluLAN Ce courriel a ete verifie par le service de securite pour courriels LastSpam (http://www.lastspam.com), fourni par SoluLAN (http://www.solulan.com) www.solulan.com
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list