ata2.00: failed to set xfermode (err_mask=0x100),ata2.00: disabled, CD-ROM drive dead
dmesg:
ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: disabled
hardware:
WD 500GB SATA on PCI Sil 3512 card (boot device)
Pioneer CD-ROM on PIIX4
kernel.org vanilla sources
2.6.31.1
2.6.32.9
Upon upgrading to 2.6.32.9 my CD-ROM is now dead.
With 2.6.31.1 I was using the libata driver along with the old style IDE driver PIIX4 and both the HD and CD-ROM worked fine.
When I rolled the new 2.6.32.9 kernel, I decided to go all libata, thus removing all the old IDE stuff in make menuconfig, and adding the PIIX4 support in the libata section along with SCSI CD-ROM support in the SCSI section, per instructions I'd found.
Relevant .config snippets:
# ProtocolsCONFIG_BLK_DEV=yCONFIG_BLK_DEV_FD=yCONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
# SCSI device supportCONFIG_SCSI=yCONFIG_SCSI_DMA=yCONFIG_SCSI_PROC_FS=y
# SCSI support type (disk, tape, CD-ROM)CONFIG_BLK_DEV_SD=yCONFIG_BLK_DEV_SR=yCONFIG_SCSI_WAIT_SCAN=m
# SCSI TransportsCONFIG_ATA=yCONFIG_ATA_VERBOSE_ERROR=yCONFIG_ATA_SFF=yCONFIG_ATA_PIIX=yCONFIG_SATA_SIL=y
I always roll my drivers into the kernel. It's just my preference, so let's please not debate the merits of kernel modules in this thread. I only mention it as menuconfig for some odd reason doesn't give me the option to roll CONFIG_SCSI_WAIT_SCAN into the kernel, but insists on making it a module. The one exception to this, apparently, is if I completely disable module support, in which case it rolls it into the kernel. It would be nice if menuconfig gave an option to force it into the kernel even if module support is enabled. Seems silly to have all the SCSI stuff built into the kernel except this one thing. I don't think this is related to the current problem, but I mention it just in case. I'm not sure if the module is
actually loading. This probably is not the right name to give modprobe but
I don't know what it would be:
~$ modprobe CONFIG_SCSI_WAIT_SCAN
FATAL: Module CONFIG_SCSI_WAIT_SCAN not found.
Anyway, should I roll another 2.6.32.9 reverting back to the dual IDE/libata driver setup to get the CD-ROM working again, or is there some neat trick you fine folks can share that will force libata to start playing nice with PIIX4 and the CD-ROM?
Thanks.
Signature · 1 line
Stan
Quoted 3 lines · Stan Hoeppner
dmesg:
ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: disabled
Can you post the full dmesg output from bootup?
Quoted 66 lines
hardware:
WD 500GB SATA on PCI Sil 3512 card (boot device)
Pioneer CD-ROM on PIIX4kernel.org vanilla sources
2.6.31.1
2.6.32.9Upon upgrading to 2.6.32.9 my CD-ROM is now dead.
With 2.6.31.1 I was using the libata driver along with the old style IDE driver PIIX4 and both the HD and CD-ROM worked fine.
When I rolled the new 2.6.32.9 kernel, I decided to go all libata, thus removing all the old IDE stuff in make menuconfig, and adding the PIIX4 support in the libata section along with SCSI CD-ROM support in the SCSI section, per instructions I'd found.
Relevant .config snippets:
# ProtocolsCONFIG_BLK_DEV=yCONFIG_BLK_DEV_FD=yCONFIG_HAVE_IDE=y
#CONFIG_IDEis not set# SCSI device support
CONFIG_SCSI=yCONFIG_SCSI_DMA=yCONFIG_SCSI_PROC_FS=y# SCSI support type (disk, tape, CD-ROM)
CONFIG_BLK_DEV_SD=yCONFIG_BLK_DEV_SR=yCONFIG_SCSI_WAIT_SCAN=m# SCSI Transports
CONFIG_ATA=yCONFIG_ATA_VERBOSE_ERROR=yCONFIG_ATA_SFF=yCONFIG_ATA_PIIX=yCONFIG_SATA_SIL=yI always roll my drivers into the kernel. It's just my preference, so let's please not debate the merits of kernel modules in this thread. I only mention it as menuconfig for some odd reason doesn't give me the option to roll
CONFIG_SCSI_WAIT_SCANinto the kernel, but insists on making it a module. The one exception to this, apparently, is if I completely disable module support, in which case it rolls it into the kernel. It would be nice if menuconfig gave an option to force it into the kernel even if module support is enabled. Seems silly to have all the SCSI stuff built into the kernel except this one thing. I don't think this is related to the current problem, but I mention it just in case. I'm not sure if the module is
actually loading. This probably is not the right name to give modprobe but
I don't know what it would be:~$ modprobe
CONFIG_SCSI_WAIT_SCAN
FATAL: ModuleCONFIG_SCSI_WAIT_SCANnot found.Anyway, should I roll another 2.6.32.9 reverting back to the dual IDE/libata driver setup to get the CD-ROM working again, or is there some neat trick you fine folks can share that will force libata to start playing nice with PIIX4 and the CD-ROM?
Thanks.
Robert Hancock put forth on 3/15/2010 6:44 PM:
Quoted 6 lines · Stan Hoeppner
Quoted 3 lines
dmesg:
ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: disabledCan you post the full dmesg output from bootup?
Sure:
Linux version 2.6.32.9 (root@greer) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Wed Mar 10 19:02:00 CST 2010
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000018000000 (usable)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
DMI 2.2 present.last_pfn = 0x18000 max_arch_pfn = 0x100000
initial memory mapped : 0 - 01800000init_memory_mapping: 0000000000000000-0000000018000000
0000000000 - 0000400000 page 4k
0000400000 - 0018000000 page 2M
kernel direct mapping tables up to 18000000 @ 7000-b000
384MB LOWMEM available.
mapped low ram: 0 - 18000000
low ram: 0 - 18000000
node 0 low ram: 00000000 - 18000000
node 0 bootmap 00002000 - 00005000
(7 early reservations) ==> bootmem [0000000000 - 0018000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0001000000 - 00012c025c] TEXT DATA BSS ==> [0001000000 - 00012c025c]
#4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#5 [00012c1000 - 00012c707a] BRK ==> [00012c1000 - 00012c707a]
#6 [0000002000 - 0000005000] BOOTMAP ==> [0000002000 - 0000005000]
found SMP MP-table at [c00f5b90] f5b90
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00018000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x000000a0
0: 0x00000100 -> 0x00018000On node 0 totalpages: 98208free_area_init_node: node 0, pgdat c125e580, node_mem_map c12c8000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3968 pages, LIFO batch:0
Normal zone: 736 pages used for memmap
Normal zone: 93472 pages, LIFO batch:31
Using APIC driver default
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
MPTABLE: OEM ID: OEM00000
MPTABLE: Product ID: PROD00000000
MPTABLE: APIC at: 0xFEE00000
Processor #0 (Bootup-CPU)
Processor #1
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
SMP: Allowing 2 CPUs, 0 hotplug CPUsnr_irqs_gsi: 24
Allocating PCI resources starting at 18000000 (gap: 18000000:e6c00000) NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 10 pages/cpu @c1800000 s20280 r0 d20680 u2097152
pcpu-alloc: s20280 r0 d20680 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 97440 Kernel command line: auto BOOT_IMAGE=Linux ro root=802
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Enabling fast FPU save and restore... done.
Initializing CPU#0
Memory: 386032k/393216k available (1772k kernel code, 6424k reserved, 660k data, 244k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff92000 - 0xfffff000 ( 436 kB)
vmalloc : 0xd8800000 - 0xfff90000 ( 631 MB)
lowmem : 0xc0000000 - 0xd8000000 ( 384 MB)
.init : 0xc1261000 - 0xc129e000 ( 244 kB)
.data : 0xc11bb258 - 0xc1260418 ( 660 kB)
.text : 0xc1000000 - 0xc11bb258 (1772 kB)Checking if this processor honours the WP bit even in supervisor mode...Ok. Hierarchical RCU implementation.
NR_IRQS:320
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 511.876 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 1023.75 BogoMIPS (lpj=2047504)
Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
mce: CPU supports 5 MCE banks
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 9k freed
ExtINT not setup in hardware but reported by MP table
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: Intel Celeron (Mendocino) stepping 05
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU1: Intel Celeron (Mendocino) stepping 05
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (2047.60 BogoMIPS).
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb440, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
pci 0000:00:00.0: reg 10 32bit mmio pref: [0xe4400000-0xe47fffff] pci 0000:00:07.1: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:07.2: reg 20 io port: [0x9000-0x901f]
pci 0000:00:07.3: quirk: region 4000-403f claimed by PIIX4 ACPI pci 0000:00:07.3: quirk: region 5000-500f claimed by PIIX4 SMB pci 0000:00:0d.0: reg 10 32bit mmio: [0xe4910000-0xe4910fff]
pci 0000:00:0d.0: reg 14 io port: [0x9400-0x943f]
pci 0000:00:0d.0: reg 18 32bit mmio: [0xe4800000-0xe48fffff]
pci 0000:00:0d.0: reg 30 32bit mmio pref: [0xe0000000-0xe00fffff] pci 0000:00:0d.0: supports D1 D2
pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0d.0: PME# disabled
pci 0000:00:0f.0: reg 10 32bit mmio: [0xe4000000-0xe43fffff]
pci 0000:00:0f.0: reg 14 32bit mmio: [0xe4900000-0xe490ffff]
pci 0000:00:0f.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] pci 0000:00:11.0: reg 10 io port: [0x9800-0x9807]
pci 0000:00:11.0: reg 14 io port: [0x9c00-0x9c03]
pci 0000:00:11.0: reg 18 io port: [0xa000-0xa007]
pci 0000:00:11.0: reg 1c io port: [0xa400-0xa403]
pci 0000:00:11.0: reg 20 io port: [0xa800-0xa80f]
pci 0000:00:11.0: reg 24 32bit mmio: [0xe4911000-0xe49111ff]
pci 0000:00:11.0: reg 30 32bit mmio pref: [0xe2000000-0xe207ffff] pci 0000:00:11.0: supports D1 D2
pci 0000:00:13.0: reg 10 io port: [0xac00-0xac07]
pci 0000:00:13.0: reg 14 io port: [0xb000-0xb003]
pci 0000:00:13.0: reg 20 io port: [0xb400-0xb4ff]
pci 0000:00:13.0: reg 30 32bit mmio pref: [0xe3000000-0xe301ffff] pci 0000:00:13.1: reg 10 io port: [0xb800-0xb807]
pci 0000:00:13.1: reg 14 io port: [0xbc00-0xbc03]
pci 0000:00:13.1: reg 20 io port: [0xc000-0xc0ff]
vgaarb: device added: PCI:0000:00:0f.0,decodes=io+mem,owns=io+mem,locks=none pci 0000:00:07.0: PIIX/ICH IRQ router [8086:7110]
Switching to clocksource tsc
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: disabled pci 0000:00:01.0: MEM window: disabled pci 0000:00:01.0: PREFETCH window: disabled
pci_bus 0000:00: resource 0 io: [0x00-0xffff]pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
pci 0000:00:00.0: Limiting direct PCI/PCI transfers
pci 0000:00:0d.0: Firmware left e100 interrupts enabled; disabling pci 0000:00:0f.0: Boot video device
platform rtc_cmos: registered platform RTC device (no PNP device found) SGI XFS with security attributes, no debug enabled
msgmni has been set to 754
io scheduler noop registered
io scheduler deadline registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077ata_piix 0000:00:07.1: version 2.13
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
ata1: port disabled. ignoring.sata_sil 0000:00:11.0: version 2.4sata_sil 0000:00:11.0: PCI->APIC IRQ transform: INT A -> IRQ 19 scsi2 : sata_sil
scsi3 : sata_sil
ata3: SATA max UDMA/100 mmio m512@0xe4911000 tf 0xe4911080 irq 19
ata4: SATA max UDMA/100 mmio m512@0xe4911000 tf 0xe49110c0 irq 19
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:00:0d.0: PCI->APIC IRQ transform: INT A -> IRQ 17
e100 0000:00:0d.0: PME# disabled
e100: eth0: e100_probe: addr 0xe4910000, irq 17, MAC addr 00:90:27:65:01:69
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all micertc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one day, 114 bytes nvram
i2c /dev entries driverpiix4_smbus 0000:00:07.3: SMBus Host Controller at 0x5000, revision 0
w83781d: Found a W83782D chip at 0x290
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: ATA-8: WDC WD5000AAKS-00V1A0, 05.01D05, max UDMA/133 ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata3.00: configured for UDMA/100
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: failed to set xfermode (err_mask=0x100)
TCP cubic registered
NET: Registered protocol family 17
Using IPI Shortcut modertc_cmos rtc_cmos: setting system clock to 2010-03-10 20:53:54 UTC (1268254434) ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: limiting speed to MWDMA2:PIO3
ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: disabled
scsi 2:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 05.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 2:0:0:0: [sda] Attached SCSI disk
ata4: SATA link down (SStatus 0 SControl 310)
VFS: Mounted root (ext2 filesystem) readonly on device 8:2. Freeing unused kernel memory: 244k freed
Adding 995988k swap on /dev/sda5. Priority:-1 extents:1 across:995988k XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
XFS mounting filesystem sda7
Ending clean XFS mount for filesystem: sda7
e100 0000:00:0d.0: firmware: using built-in firmware e100/d101m_ucode.bin
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
warning: `ntpd' uses 32-bit capabilities (legacy support in use)
e100: eth0 NIC Link is Down
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
Signature · 1 line
Stan
Hello,
Quoted 9 lines · Stan Hoeppner
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: failed to set xfermode (err_mask=0x100)
TCP cubic registered
NET: Registered protocol family 17
Using IPI Shortcut modertc_cmosrtc_cmos: setting system clock to 2010-03-10 20:53:54 UTC (1268254434) ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: limiting speed to MWDMA2:PIO3
ata2.00: failed to set xfermode (err_mask=0x100)
AC_ERR_OTHER on SETXFER, that's rare. Maybe the drive needs ATA_HORKAGE_NOSETXFER? Can you please post boot log with ide driver?
Thanks.
Signature · 1 line
tejun
Tejun Heo put forth on 3/24/2010 7:38 PM:
Quoted 13 lines
Hello,
Quoted 9 lines · Stan Hoeppner
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: failed to set xfermode (err_mask=0x100)
TCP cubic registered
NET: Registered protocol family 17
Using IPI Shortcut modertc_cmosrtc_cmos: setting system clock to 2010-03-10 20:53:54 UTC (1268254434) ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: limiting speed to MWDMA2:PIO3
ata2.00: failed to set xfermode (err_mask=0x100)
Quoted 2 lines
AC_ERR_OTHERon SETXFER, that's rare. Maybe the drive needsATA_HORKAGE_NOSETXFER? Can you please post boot log with ide driver?
Hello Tejun,
Here is the relevant dmesg output for my kernel with the PIIX IDE driver:
Linux version 2.6.32.9 (root@greer) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Wed Mar 17 20:21:58 CDT 2010
...
Uniform Multi-Platform E-IDE driver
piix 0000:00:07.1: IDE controller (0x8086:0x7111 rev 0x01)
piix 0000:00:07.1: IDE port disabled
piix 0000:00:07.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf008-0xf00f
Probing IDE interface ide0...
hda: Pioneer CD-ROM ATAPI Model DR-A24X 0102, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: MWDMA2 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
ide-cd driver 5.00
ide-cd: hda: ATAPI 20X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
I must admit the CD-ROM drive is rather old, a late 90's model slot loading Pioneer drive, but it works fine with the PIIX IDE driver. If it is needed for success under libata, where would I set ATA_HORKAGE_NOSETXFER?
I have no problem continuing to use the PIIX IDE driver, but I understand all of the old IDE drivers are or will be deprecated in the not to distant future. This is why I tried to get the drive working under libata.
Thanks.
Signature · 1 line
Stan
Quoted 38 lines · Stan Hoeppner
Tejun Heo put forth on 3/24/2010 7:38 PM:
Quoted 13 lines
Hello,
Quoted 9 lines · Stan Hoeppner
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: failed to set xfermode (err_mask=0x100)
TCP cubic registered
NET: Registered protocol family 17
Using IPI Shortcut modertc_cmosrtc_cmos: setting system clock to 2010-03-10 20:53:54 UTC (1268254434) ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: limiting speed to MWDMA2:PIO3
ata2.00: failed to set xfermode (err_mask=0x100)Quoted 2 lines
AC_ERR_OTHERon SETXFER, that's rare. Maybe the drive needsATA_HORKAGE_NOSETXFER? Can you please post boot log with ide driver?Hello Tejun,
Here is the relevant dmesg output for my kernel with the PIIX IDE driver:
Linux version 2.6.32.9 (root@greer) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Wed Mar 17 20:21:58 CDT 2010
...
Uniform Multi-Platform E-IDE driver
piix 0000:00:07.1: IDE controller (0x8086:0x7111 rev0x01)
piix 0000:00:07.1: IDE port disabled
piix 0000:00:07.1: not 100% native mode: will probe irqs lateride0: BM-DMA at 0xf008-0xf00fProbing IDE interface ide0...
hda: Pioneer CD-ROM ATAPI Model DR-A24X 0102, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: MWDMA2 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
ide-cd driver 5.00
ide-cd: hda: ATAPI 20X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
Quoted 3 lines
I must admit the CD-ROM drive is rather old, a late 90's model slot loading Pioneer drive, but it works fine with the PIIX IDE driver. If it is needed for success under libata, where would I set
ATA_HORKAGE_NOSETXFER?
Hello,
If you are going to try to skip SETXFER, I think you will need an entry in ata_device_blacklist, something like this.
drivers/ata/libata-core.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)
drivers/ata/libata-core.c +1 -0
@@ -4388,6 +4388,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {* device and controller are SATA. */ { "PIONEER DVD-RW DVRTD08", "1.00", ATA_HORKAGE_NOSETXFER }, + { "Pioneer CD-ROM ATAPI Model DR-A24X 0102", "E1.02", ATA_HORKAGE_NOSETXFER }, /* End Marker */ { }
David Milburn put forth on 3/25/2010 4:52 PM:
Quoted 56 lines · Stan Hoeppner
Quoted 38 lines
Tejun Heo put forth on 3/24/2010 7:38 PM:
Quoted 13 lines
Hello,
Quoted 9 lines · Stan Hoeppner
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: failed to set xfermode (err_mask=0x100)
TCP cubic registered
NET: Registered protocol family 17
Using IPI Shortcut modertc_cmosrtc_cmos: setting system clock to 2010-03-10 20:53:54 UTC (1268254434) ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: limiting speed to MWDMA2:PIO3
ata2.00: failed to set xfermode (err_mask=0x100)Quoted 2 lines
AC_ERR_OTHERon SETXFER, that's rare. Maybe the drive needsATA_HORKAGE_NOSETXFER? Can you please post boot log with ide driver?Hello Tejun,
Here is the relevant dmesg output for my kernel with the PIIX IDE driver:
Linux version 2.6.32.9 (root@greer) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Wed Mar 17 20:21:58 CDT 2010
...
Uniform Multi-Platform E-IDE driver
piix 0000:00:07.1: IDE controller (0x8086:0x7111 rev0x01)
piix 0000:00:07.1: IDE port disabled
piix 0000:00:07.1: not 100% native mode: will probe irqs lateride0: BM-DMA at 0xf008-0xf00fProbing IDE interface ide0...
hda: Pioneer CD-ROM ATAPI Model DR-A24X 0102, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: MWDMA2 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
ide-cd driver 5.00
ide-cd: hda: ATAPI 20X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20Quoted 3 lines
I must admit the CD-ROM drive is rather old, a late 90's model slot loading Pioneer drive, but it works fine with the PIIX IDE driver. If it is needed for success under libata, where would I set
ATA_HORKAGE_NOSETXFER?Hello,
If you are going to try to skip SETXFER, I think you will need an entry in
ata_device_blacklist, something like this.drivers/ata/libata-core.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)drivers/ata/libata-core.c +0
-0
drivers/ata/libata-core.c static const struct ata_blacklist_entry ata_device_blacklist [] = { · line 4394
Quoted 7 lines
drivers/ata/libata-core.c +1
-0@@ -4388,6 +4388,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {* device and controller are SATA. */ { "PIONEER DVD-RW DVRTD08", "1.00", ATA_HORKAGE_NOSETXFER }, + { "Pioneer CD-ROM ATAPI Model DR-A24X 0102", "E1.02", ATA_HORKAGE_NOSETXFER }, /* End Marker */ { }
I tried this but it doesn't work:
ata_piix 0000:00:07.1: version 2.13
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
ata1: port disabled. ignoring.
...
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunction ata2.00: failed to set xfermode (err_mask=0x100)
...
ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunction ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: limiting speed to MWDMA2:PIO3
ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunction ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: disabled
The old IDE subsystem and piix.c combo set the xfer mode on this CD-ROM drive just fine, and the drive works fine. Both this IDE chip and the CD-ROM drive are well over 10 years old, from around 1998/99 time frame. I would think their behavior would be well understood by now. The libata and ata_piix combo seem to have a problem here. I guess that's why they are labeled 'experimental' in menuconfig. Let me know what else I can do to help this along. IIRC, the goal is to completely eliminate the old IDE subsystem in favor of libata. I'm guessing that can't happen until issues such as this case are resolved.
Signature · 1 line
Stan
Quoted 67 lines · Stan Hoeppner
David Milburn put forth on 3/25/2010 4:52 PM:
Quoted 56 lines · Stan Hoeppner
Quoted 38 lines
Tejun Heo put forth on 3/24/2010 7:38 PM:
Quoted 13 lines
Hello,
Quoted 9 lines · Stan Hoeppner
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: failed to set xfermode (err_mask=0x100)
TCP cubic registered
NET: Registered protocol family 17
Using IPI Shortcut modertc_cmosrtc_cmos: setting system clock to 2010-03-10 20:53:54 UTC (1268254434) ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: limiting speed to MWDMA2:PIO3
ata2.00: failed to set xfermode (err_mask=0x100)Quoted 2 lines
AC_ERR_OTHERon SETXFER, that's rare. Maybe the drive needsATA_HORKAGE_NOSETXFER? Can you please post boot log with ide driver?Hello Tejun,
Here is the relevant dmesg output for my kernel with the PIIX IDE driver:
Linux version 2.6.32.9 (root@greer) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 SMP Wed Mar 17 20:21:58 CDT 2010
...
Uniform Multi-Platform E-IDE driver
piix 0000:00:07.1: IDE controller (0x8086:0x7111 rev0x01)
piix 0000:00:07.1: IDE port disabled
piix 0000:00:07.1: not 100% native mode: will probe irqs lateride0: BM-DMA at 0xf008-0xf00fProbing IDE interface ide0...
hda: Pioneer CD-ROM ATAPI Model DR-A24X 0102, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: MWDMA2 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
ide-cd driver 5.00
ide-cd: hda: ATAPI 20X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20Quoted 3 lines
I must admit the CD-ROM drive is rather old, a late 90's model slot loading Pioneer drive, but it works fine with the PIIX IDE driver. If it is needed for success under libata, where would I set
ATA_HORKAGE_NOSETXFER?Hello,
If you are going to try to skip SETXFER, I think you will need an entry in
ata_device_blacklist, something like this.drivers/ata/libata-core.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)drivers/ata/libata-core.c +0
-0drivers/ata/libata-core.c static const struct ata_blacklist_entry ata_device_blacklist [] = { · line 4394
Quoted 7 lines
drivers/ata/libata-core.c +1
-0@@ -4388,6 +4388,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {* device and controller are SATA. */ { "PIONEER DVD-RW DVRTD08", "1.00", ATA_HORKAGE_NOSETXFER }, + { "Pioneer CD-ROM ATAPI Model DR-A24X 0102", "E1.02", ATA_HORKAGE_NOSETXFER }, /* End Marker */ { }I tried this but it doesn't work:
Quoted 9 lines
ata_piix0000:00:07.1: version 2.13
scsi0 :ata_piix
scsi1 :ata_piix
ata1: PATA max UDMA/33 cmd0x1f0ctl0x3f6bmdma0xf000irq 14
ata2: PATA max UDMA/33 cmd0x170ctl0x376bmdma0xf008irq 15
ata1: port disabled. ignoring.
...
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunction
Yeah, NOSETXFER doesn't take effect on PATA drives. It could, but it would assume that the BIOS has set the right mode which seems rather dangerous.
Shouldn't we be getting some error handling output from the command failing?
Quoted 9 lines
ata2.00: failed to set xfermode (err_mask=0x100)
...
ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunction ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: limiting speed to MWDMA2:PIO3
ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunction ata2.00: failed to set xfermode (err_mask=0x100)
ata2.00: disabled
Quoted 6 lines
The old IDE subsystem and
piix.ccombo set the xfer mode on this CD-ROM drive just fine, and the drive works fine. Both this IDE chip and the CD-ROM drive are well over 10 years old, from around 1998/99 time frame. I would think their behavior would be well understood by now. The libata andata_piixcombo seem to have a problem here. I guess that's why they are labeled 'experimental' in menuconfig. Let me know what else I can do to
They're not anymore, actually.
Quoted 4 lines
help this along. IIRC, the goal is to completely eliminate the old IDE subsystem in favor of libata. I'm guessing that can't happen until issues such as this case are resolved.
Hello,
Quoted 8 lines · Robert Hancock
Quoted 4 lines
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2
ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunctionYeah, NOSETXFER doesn't take effect on PATA drives. It could, but it would assume that the BIOS has set the right mode which seems rather dangerous.
Well, we can issue the command, ignore the error and then check the correct mode is configured during revalidation. For now, the following should show us whether something like that would work.
drivers/ata/libata-core.c +4 -0
@@ -3446,6 +3446,10 @@ static int ata_dev_set_mode(struct ata_device *dev)"NOSETXFER but PATA detected - can't " "skip SETXFER, might malfunction\n"); err_mask =ata_dev_set_xfermode (dev); +if (err_mask) +ata_dev_printk (dev,KERN_WARNING ,"SETXFER failed w/ %x\n" , + err_mask); + err_mask =0 ; }if (err_mask & ~AC_ERR_DEV )
Signature · 1 line
tejun
Tejun Heo put forth on 3/28/2010 6:47 PM:
Quoted 21 lines
Hello,
Quoted 8 lines · Robert Hancock
Quoted 4 lines
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2
ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunctionYeah, NOSETXFER doesn't take effect on PATA drives. It could, but it would assume that the BIOS has set the right mode which seems rather dangerous.
Well, we can issue the command, ignore the error and then check the correct mode is configured during revalidation. For now, the following should show us whether something like that would work.
drivers/ata/libata-core.c +0
-0
drivers/ata/libata-core.c static int ata_dev_set_mode(struct ata_device *dev) · line 3455
Quoted 10 lines
drivers/ata/libata-core.c +4
-0@@ -3446,6 +3446,10 @@ static int ata_dev_set_mode(struct ata_device *dev)"NOSETXFER but PATA detected - can't " "skip SETXFER, might malfunction\n"); err_mask =ata_dev_set_xfermode (dev); +if (err_mask) +ata_dev_printk (dev,KERN_WARNING ,"SETXFER failed w/ %x\n" , + err_mask); + err_mask =0 ; }if (err_mask & ~AC_ERR_DEV )
I'm still using 2.6.32.9. Is it ok to apply this against 2.6.32.9?
Signature · 1 line
Stan
Quoted 14 lines · Stan Hoeppner
Quoted 14 lines
drivers/ata/libata-core.c +4
-0@@ -3446,6 +3446,10 @@ static int ata_dev_set_mode(struct ata_device *dev)"NOSETXFER but PATA detected - can't " "skip SETXFER, might malfunction\n"); err_mask =ata_dev_set_xfermode (dev); +if (err_mask) +ata_dev_printk (dev,KERN_WARNING ,"SETXFER failed w/ %x\n" , + err_mask); + err_mask =0 ; }
Quoted 4 lines
drivers/ata/libata-core.c static int ata_dev_set_mode(struct ata_device *dev) · line 3455
Quoted 1 line
drivers/ata/libata-core.c +0
-0if (err_mask & ~AC_ERR_DEV )I'm still using 2.6.32.9. Is it ok to apply this against 2.6.32.9?
Yeah, that part hasn't changed lately so it should be okay.
Signature · 1 line
tejun
Stan Hoeppner put forth on 3/28/2010 7:09 PM:
Quoted 31 lines
Tejun Heo put forth on 3/28/2010 6:47 PM:
Quoted 30 lines
Hello,
Quoted 8 lines · Robert Hancock
Quoted 4 lines
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2
ata2.00: NOSETXFER but PATA detected - can't skip SETXFER, might malfunctionYeah, NOSETXFER doesn't take effect on PATA drives. It could, but it would assume that the BIOS has set the right mode which seems rather dangerous.
Well, we can issue the command, ignore the error and then check the correct mode is configured during revalidation. For now, the following should show us whether something like that would work.
drivers/ata/libata-core.c +4
-0@@ -3446,6 +3446,10 @@ static int ata_dev_set_mode(struct ata_device *dev)"NOSETXFER but PATA detected - can't " "skip SETXFER, might malfunction\n"); err_mask =ata_dev_set_xfermode (dev); +if (err_mask) +ata_dev_printk (dev,KERN_WARNING ,"SETXFER failed w/ %x\n" , + err_mask); + err_mask =0 ; }
Quoted 4 lines
drivers/ata/libata-core.c static int ata_dev_set_mode(struct ata_device *dev) · line 3455
Quoted 1 line
drivers/ata/libata-core.c +0
-0if (err_mask & ~AC_ERR_DEV )I'm still using 2.6.32.9. Is it ok to apply this against 2.6.32.9?
Oh, and do I need to keep the black list entry or get rid of it?
Signature · 1 line
Stan
Quoted 3 lines · Stan Hoeppner
Quoted 1 line
I'm still using 2.6.32.9. Is it ok to apply this against 2.6.32.9?
Oh, and do I need to keep the black list entry or get rid of it?
It doesn't matter. It has no effect anyway.
Signature · 1 line
tejun
Tejun Heo put forth on 3/28/2010 7:25 PM:
Quoted 15 lines · Stan Hoeppner
Quoted 14 lines
Quoted 14 lines
drivers/ata/libata-core.c +4
-0@@ -3446,6 +3446,10 @@ static int ata_dev_set_mode(struct ata_device *dev)"NOSETXFER but PATA detected - can't " "skip SETXFER, might malfunction\n"); err_mask =ata_dev_set_xfermode (dev); +if (err_mask) +ata_dev_printk (dev,KERN_WARNING ,"SETXFER failed w/ %x\n" , + err_mask); + err_mask =0 ; }
Quoted 6 lines
Quoted 4 lines
drivers/ata/libata-core.c static int ata_dev_set_mode(struct ata_device *dev) · line 3455
Quoted 1 line
drivers/ata/libata-core.c +0
-0if (err_mask & ~AC_ERR_DEV )I'm still using 2.6.32.9. Is it ok to apply this against 2.6.32.9?
Yeah, that part hasn't changed lately so it should be okay.
This patch seems to have done the trick Tejun. Thank you. Device mount and read access seem to be slower than with the IDE driver. But given how little I use the CD-ROM drive this initial impression may not accurately describe reality. Here's relevant dmesg entries from the patched kernel:
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
ata1: port disabled. ignoring.
ata2.00: ATAPI: Pioneer CD-ROM ATAPI Model DR-A24X 0102, E1.02, max MWDMA2 ata2.00: SETXFER failed w/ 100
ata2.00: configured for MWDMA2
scsi 1:0:0:0: CD-ROM PIONEER CD-ROM DR-A01S 1.02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 20x/20x xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
Thanks.
Signature · 1 line
Stan