nios2: remove EP1C20, EP1S10, EP1S40 boards

The example configuration files of nios2-generic board can generated binary to run on the EP1C20, EP1S10, and EP1S40 boards. So the three boards can be removed.

With nios2-generic approach, the fpga parameter header file can be generated from hardware designs using tools. Porting u-boot for nios2 boards is simplified. Vendors can supply their fpga parameter file or patches to add a new nios2-generic board instance. There is no need to include other boards support for nios2 in the u-boot mainline.

Signed-off-by Thomas Chou <[email protected]>

---
Hi Scott, please rebase your next branch to Wolfgang's next, 06/14.

v2: rebased to Makefile simplify

 MAINTAINERS                   |    3 -
 MAKEALL                       |    3 -
 board/altera/ep1c20/Makefile  |   55 -----------
 board/altera/ep1c20/config.mk |   31 ------
 board/altera/ep1c20/ep1c20.c  |   52 ----------
 board/altera/ep1s10/Makefile  |   55 -----------
 board/altera/ep1s10/config.mk |   31 ------
 board/altera/ep1s10/ep1s10.c  |   52 ----------
 board/altera/ep1s40/Makefile  |   55 -----------
 board/altera/ep1s40/config.mk |   31 ------
 board/altera/ep1s40/ep1s40.c  |   47 ---------
 boards.cfg                    |    3 -
 include/configs/EP1C20.h      |  214 -----------------------------------------
 include/configs/EP1S10.h      |  207 ---------------------------------------
 include/configs/EP1S40.h      |  207 ---------------------------------------
 15 files changed, 0 insertions(+), 1046 deletions(-)
 delete mode 100644 board/altera/ep1c20/Makefile
 delete mode 100644 board/altera/ep1c20/config.mk
 delete mode 100644 board/altera/ep1c20/ep1c20.c
 delete mode 100644 board/altera/ep1s10/Makefile
 delete mode 100644 board/altera/ep1s10/config.mk
 delete mode 100644 board/altera/ep1s10/ep1s10.c
 delete mode 100644 board/altera/ep1s40/Makefile
 delete mode 100644 board/altera/ep1s40/config.mk
 delete mode 100644 board/altera/ep1s40/ep1s40.c
 delete mode 100644 include/configs/EP1C20.h
 delete mode 100644 include/configs/EP1S10.h
 delete mode 100644 include/configs/EP1S40.h

MAINTAINERS +0 -3

index 7a13d28..700dd8c 100644
@@ -852,9 +852,6 @@ Scott McNutt <[email protected]>
 
 	PCI5441		Nios-II
 	PK1C20		Nios-II
-	EP1C20		Nios-II
-	EP1S10		Nios-II
-	EP1S40		Nios-II
 	nios2-generic	Nios-II
 
 #########################################################################

MAKEALL +0 -3

index 2527352..56db729 100755
@@ -815,9 +815,6 @@ LIST_x86="		\
 #########################################################################
 
 LIST_nios2="		\
-	EP1C20		\
-	EP1S10		\
-	EP1S40		\
 	PCI5441		\
 	PK1C20		\
 	nios2-generic	\

board/altera/ep1c20/Makefile deleted +0 -55

deleted file mode 100644
index acad2aa..0000000
@@ -1,55 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB	= $(obj)lib$(BOARD).a
-
-COMOBJS := ../common/AMDLV065D.o ../common/epled.o
-
-COBJS	:= $(BOARD).o $(COMOBJS)
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS)
-
-clean:
-	rm -f $(SOBJS) $(OBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################

board/altera/ep1c20/config.mk deleted +0 -31

deleted file mode 100644
index dab2740..0000000
@@ -1,31 +0,0 @@
-#
-# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
-# Scott McNutt <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-TEXT_BASE = 0x01fc0000
-
-PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
-PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif

board/altera/ep1c20/ep1c20.c deleted +0 -52

deleted file mode 100644
index 82900f7..0000000
@@ -1,52 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <[email protected]>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-
-int board_early_init_f (void)
-{
-	return 0;
-}
-
-int checkboard (void)
-{
-	puts ("BOARD : Altera EP-1C20\n");
-	return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
-	return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_SMC91111
-	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
-	return rc;
-}
-#endif

board/altera/ep1s10/Makefile deleted +0 -55

deleted file mode 100644
index acad2aa..0000000
@@ -1,55 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB	= $(obj)lib$(BOARD).a
-
-COMOBJS := ../common/AMDLV065D.o ../common/epled.o
-
-COBJS	:= $(BOARD).o $(COMOBJS)
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS)
-
-clean:
-	rm -f $(SOBJS) $(OBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################

board/altera/ep1s10/config.mk deleted +0 -31

deleted file mode 100644
index dab2740..0000000
@@ -1,31 +0,0 @@
-#
-# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
-# Scott McNutt <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-TEXT_BASE = 0x01fc0000
-
-PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
-PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif

board/altera/ep1s10/ep1s10.c deleted +0 -52

deleted file mode 100644
index cf886da..0000000
@@ -1,52 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <[email protected]>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-
-int board_early_init_f (void)
-{
-	return 0;
-}
-
-int checkboard (void)
-{
-	puts ("BOARD : Altera EP-1S10\n");
-	return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
-	return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_SMC91111
-	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
-	return rc;
-}
-#endif

board/altera/ep1s40/Makefile deleted +0 -55

deleted file mode 100644
index acad2aa..0000000
@@ -1,55 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB	= $(obj)lib$(BOARD).a
-
-COMOBJS := ../common/AMDLV065D.o ../common/epled.o
-
-COBJS	:= $(BOARD).o $(COMOBJS)
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-$(LIB):	$(obj).depend $(OBJS)
-	$(AR) $(ARFLAGS) $@ $(OBJS)
-
-clean:
-	rm -f $(SOBJS) $(OBJS)
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################

board/altera/ep1s40/config.mk deleted +0 -31

deleted file mode 100644
index dab2740..0000000
@@ -1,31 +0,0 @@
-#
-# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
-# Scott McNutt <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-TEXT_BASE = 0x01fc0000
-
-PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
-PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif

board/altera/ep1s40/ep1s40.c deleted +0 -47

deleted file mode 100644
index 6395de7..0000000
@@ -1,47 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <[email protected]>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-
-int checkboard (void)
-{
-	puts ("BOARD : Altera EP-1S40\n");
-	return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
-	return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_SMC91111
-	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
-	return rc;
-}
-#endif

boards.cfg +0 -3

index e54673e..9b126a3 100644
@@ -75,9 +75,6 @@ M5272C3		m68k	mcf52x2		m5272c3		freescale
 EP2500		m68k	mcf52x2		ep2500		Mercury
 purple		mips	mips
 tb0229		mips	mips
-EP1C20		nios2	nios2		ep1c20		altera
-EP1S10		nios2	nios2		ep1s10		altera
-EP1S40		nios2	nios2		ep1s40		altera
 PCI5441		nios2	nios2		pci5441		psyent
 PK1C20		nios2	nios2		pk1c20		psyent
 P3G4		powerpc	74xx_7xx	evb64260

include/configs/EP1C20.h deleted +0 -214

deleted file mode 100644
index 3920d35..0000000
@@ -1,214 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <[email protected]>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*------------------------------------------------------------------------
- * BOARD/CPU
- *----------------------------------------------------------------------*/
-#define CONFIG_EP1C20		1		/* EP1C20 board		*/
-#define CONFIG_SYS_CLK_FREQ	50000000	/* 50 MHz core clk	*/
-
-#define CONFIG_SYS_RESET_ADDR		0x00000000	/* Hard-reset address	*/
-#define CONFIG_SYS_EXCEPTION_ADDR	0x01000020	/* Exception entry point*/
-#define CONFIG_SYS_NIOS_SYSID_BASE	0x021208b8	/* System id address	*/
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* enable early board-spec. init*/
-
-/*------------------------------------------------------------------------
- * CACHE -- the following will support II/s and II/f. The II/s does not
- * have dcache, so the cache instructions will behave as NOPs.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_ICACHE_SIZE		4096		/* 4 KByte total	*/
-#define CONFIG_SYS_ICACHELINE_SIZE	32		/* 32 bytes/line	*/
-#define CONFIG_SYS_DCACHE_SIZE		2048		/* 2 KByte (II/f)	*/
-#define CONFIG_SYS_DCACHELINE_SIZE	4		/* 4 bytes/line (II/f)	*/
-
-/*------------------------------------------------------------------------
- * MEMORY BASE ADDRESSES
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE		0x00000000	/* FLASH base addr	*/
-#define CONFIG_SYS_FLASH_SIZE		0x00800000	/* 8 MByte		*/
-#define CONFIG_SYS_SDRAM_BASE		0x01000000	/* SDRAM base addr	*/
-#define CONFIG_SYS_SDRAM_SIZE		0x01000000	/* 16 MByte		*/
-#define CONFIG_SYS_SRAM_BASE		0x02000000	/* SRAM base addr	*/
-#define CONFIG_SYS_SRAM_SIZE		0x00100000	/* 1 MB (only 1M mapped)*/
-
-/*------------------------------------------------------------------------
- * MEMORY ORGANIZATION
- *	-Monitor at top.
- *	-The heap is placed below the monitor.
- *	-Global data is placed below the heap.
- *	-The stack is placed below global data (&grows down).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 128k		*/
-#define CONFIG_SYS_GBL_DATA_SIZE	128		/* Global data size rsvd*/
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
-
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP		CONFIG_SYS_GBL_DATA_OFFSET
-
-/*------------------------------------------------------------------------
- * FLASH (AM29LV065D)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128		/* Max # sects per bank */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* Max # of flash banks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	8000		/* Erase timeout (msec) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	100		/* Write timeout (msec) */
-#define CONFIG_SYS_FLASH_WORD_SIZE	unsigned char	/* flash word size	*/
-
-/*------------------------------------------------------------------------
- * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
- * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
- * reset address, no? This will keep the environment in user region
- * of flash. NOTE: the monitor length must be multiple of sector size
- * (which is common practice).
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH	1		/* Environment in flash */
-#define CONFIG_ENV_SIZE		(64 * 1024)	/* 64 KByte (1 sector)	*/
-#define CONFIG_ENV_OVERWRITE			/* Serial change Ok	*/
-#define CONFIG_ENV_ADDR	(CONFIG_SYS_RESET_ADDR + CONFIG_SYS_MONITOR_LEN)
-
-/*------------------------------------------------------------------------
- * CONSOLE
- *----------------------------------------------------------------------*/
-#define CONFIG_ALTERA_UART		1	/* Use altera uart */
-#if defined(CONFIG_ALTERA_JTAG_UART)
-#define CONFIG_SYS_NIOS_CONSOLE	0x021208b0	/* JTAG UART base addr	*/
-#else
-#define CONFIG_SYS_NIOS_CONSOLE	0x02120840	/* UART base addr	*/
-#endif
-
-#define CONFIG_SYS_NIOS_FIXEDBAUD	1		/* Baudrate is fixed	*/
-#define CONFIG_BAUDRATE		115200		/* Initial baudrate	*/
-#define CONFIG_SYS_BAUDRATE_TABLE	{115200}	/* It's fixed ;-)	*/
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1		/* Suppress console info*/
-
-/*------------------------------------------------------------------------
- * EPCS Device -- wne CONFIG_SYS_NIOS_EPCSBASE is defined code/commands for
- * epcs device access is enabled. The base address is the epcs
- * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK.
- * The register base is currently at offset 0x600 from the memory base.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_NIOS_EPCSBASE	0x02100200	/* EPCS register base	*/
-
-/*------------------------------------------------------------------------
- * DEBUG
- *----------------------------------------------------------------------*/
-#undef CONFIG_ROM_STUBS				/* Stubs not in ROM	*/
-
-/*------------------------------------------------------------------------
- * TIMEBASE --
- *
- * The high res timer defaults to 1 msec. Since it includes the period
- * registers, the interrupt frequency can be reduced using TMRCNT.
- * If the default period is acceptable, TMRCNT can be left undefined.
- * TMRMS represents the desired mecs per tick (msecs per interrupt).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_HZ			1000	/* Always 1000 */
-#define CONFIG_SYS_NIOS_TMRBASE	0x02120820	/* Tick timer base addr */
-#define CONFIG_SYS_NIOS_TMRIRQ		3	/* Timer IRQ num	*/
-#define CONFIG_SYS_NIOS_TMRMS		10	/* Desired period (msec)*/
-#define CONFIG_SYS_NIOS_TMRCNT \
-		(CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
-
-/*------------------------------------------------------------------------
- * STATUS LED -- Provides a simple blinking led. For Nios2 each board
- * must implement its own led routines -- leds are, after all,
- * board-specific, no?
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LEDPIO_ADDR		0x02120870	/* LED PIO base addr	*/
-#define CONFIG_STATUS_LED			/* Enable status driver */
-
-#define STATUS_LED_BIT		1		/* Bit-0 on PIO		*/
-#define STATUS_LED_STATE	1		/* Blinking		*/
-#define STATUS_LED_PERIOD	(500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec	*/
-
-/*------------------------------------------------------------------------
- * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
- * and really doesn't need any additional clutter. So I choose the lazy
- * way out to avoid changes there -- define the base address to ensure
- * cache bypass so there's no need to monkey with inx/outx macros.
- *----------------------------------------------------------------------*/
-#define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
-#define CONFIG_NET_MULTI
-#define CONFIG_SMC91111			/* Using SMC91c111	*/
-#undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
-#define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
-
-#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_IPADDR		192.168.2.21
-#define CONFIG_SERVERIP		192.168.2.16
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-
-#undef CONFIG_CMD_BOOTD
-#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_ITEST
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_XIMG
-
-
-/*------------------------------------------------------------------------
- * MISC
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP				/* Provide extended help*/
-#define CONFIG_SYS_PROMPT		"==> "		/* Command prompt	*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O buf size */
-#define CONFIG_SYS_MAXARGS		16		/* Max command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot arg buf size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE	/* Default load address */
-#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE	/* Start addr for test	*/
-#define CONFIG_SYS_MEMTEST_END		CONFIG_SYS_INIT_SP - 0x00020000
-
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-
-#endif	/* __CONFIG_H */

include/configs/EP1S10.h deleted +0 -207

deleted file mode 100644
index bfbf8c1..0000000
@@ -1,207 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <[email protected]>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*------------------------------------------------------------------------
- * BOARD/CPU
- *----------------------------------------------------------------------*/
-#define CONFIG_EP1S10		1		/* EP1S10 board		*/
-#define CONFIG_SYS_CLK_FREQ	50000000	/* 50 MHz core clk	*/
-
-#define CONFIG_SYS_RESET_ADDR		0x00000000	/* Hard-reset address	*/
-#define CONFIG_SYS_EXCEPTION_ADDR	0x01000020	/* Exception entry point*/
-#define CONFIG_SYS_NIOS_SYSID_BASE	0x021208b8	/* System id address	*/
-
-/*------------------------------------------------------------------------
- * CACHE -- the following will support II/s and II/f. The II/s does not
- * have dcache, so the cache instructions will behave as NOPs.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_ICACHE_SIZE		4096		/* 4 KByte total	*/
-#define CONFIG_SYS_ICACHELINE_SIZE	32		/* 32 bytes/line	*/
-#define CONFIG_SYS_DCACHE_SIZE		2048		/* 2 KByte (II/f)	*/
-#define CONFIG_SYS_DCACHELINE_SIZE	4		/* 4 bytes/line (II/f)	*/
-
-/*------------------------------------------------------------------------
- * MEMORY BASE ADDRESSES
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE		0x00000000	/* FLASH base addr	*/
-#define CONFIG_SYS_FLASH_SIZE		0x00800000	/* 8 MByte		*/
-#define CONFIG_SYS_SDRAM_BASE		0x01000000	/* SDRAM base addr	*/
-#define CONFIG_SYS_SDRAM_SIZE		0x01000000	/* 16 MByte		*/
-#define CONFIG_SYS_SRAM_BASE		0x02000000	/* SRAM base addr	*/
-#define CONFIG_SYS_SRAM_SIZE		0x00100000	/* 1 MB			*/
-
-/*------------------------------------------------------------------------
- * MEMORY ORGANIZATION
- *	-Monitor at top.
- *	-The heap is placed below the monitor.
- *	-Global data is placed below the heap.
- *	-The stack is placed below global data (&grows down).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256k		*/
-#define CONFIG_SYS_GBL_DATA_SIZE	128		/* Global data size rsvd*/
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 256*1024) /* 256k heap */
-
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP		CONFIG_SYS_GBL_DATA_OFFSET
-
-/*------------------------------------------------------------------------
- * FLASH (AM29LV065D)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128		/* Max # sects per bank */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* Max # of flash banks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	8000		/* Erase timeout (msec) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	100		/* Write timeout (msec) */
-
-/*------------------------------------------------------------------------
- * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
- * CONFIG_SYS_FLASH_BASE, since we assume that u-boot is stored at the bottom
- * of flash memory. This will keep the environment in user region
- * of flash. NOTE: the monitor length must be multiple of sector size
- * (which is common practice).
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH	1		/* Environment in flash */
-#define CONFIG_ENV_SIZE		(64 * 1024)	/* 64 KByte (1 sector)	*/
-#define CONFIG_ENV_OVERWRITE			/* Serial change Ok	*/
-#define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
-
-/*------------------------------------------------------------------------
- * CONSOLE
- *----------------------------------------------------------------------*/
-#define CONFIG_ALTERA_UART		1	/* Use altera uart */
-#if defined(CONFIG_ALTERA_JTAG_UART)
-#define CONFIG_SYS_NIOS_CONSOLE	0x021208b0	/* JTAG UART base addr	*/
-#else
-#define CONFIG_SYS_NIOS_CONSOLE	0x02120840	/* UART base addr	*/
-#endif
-
-#define CONFIG_SYS_NIOS_FIXEDBAUD	1		/* Baudrate is fixed	*/
-#define CONFIG_BAUDRATE		115200		/* Initial baudrate	*/
-#define CONFIG_SYS_BAUDRATE_TABLE	{115200}	/* It's fixed ;-)	*/
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1		/* Suppress console info*/
-
-/*------------------------------------------------------------------------
- * EPCS Device -- None for stratix.
- *----------------------------------------------------------------------*/
-#undef CONFIG_SYS_NIOS_EPCSBASE
-
-/*------------------------------------------------------------------------
- * DEBUG
- *----------------------------------------------------------------------*/
-#undef CONFIG_ROM_STUBS				/* Stubs not in ROM	*/
-
-/*------------------------------------------------------------------------
- * TIMEBASE --
- *
- * The high res timer defaults to 1 msec. Since it includes the period
- * registers, the interrupt frequency can be reduced using TMRCNT.
- * If the default period is acceptable, TMRCNT can be left undefined.
- * TMRMS represents the desired mecs per tick (msecs per interrupt).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_HZ			1000	/* Always 1000 */
-#define CONFIG_SYS_NIOS_TMRBASE	0x02120820	/* Tick timer base addr */
-#define CONFIG_SYS_NIOS_TMRIRQ		3	/* Timer IRQ num */
-#define CONFIG_SYS_NIOS_TMRMS		10	/* Desired period (msec)*/
-#define CONFIG_SYS_NIOS_TMRCNT \
-		(CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
-
-/*------------------------------------------------------------------------
- * STATUS LED -- Provides a simple blinking led. For Nios2 each board
- * must implement its own led routines -- since leds are board-specific.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LEDPIO_ADDR		0x02120870	/* LED PIO base addr	*/
-#define CONFIG_STATUS_LED			/* Enable status driver */
-
-#define STATUS_LED_BIT		1		/* Bit-0 on PIO		*/
-#define STATUS_LED_STATE	1		/* Blinking		*/
-#define STATUS_LED_PERIOD	(500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec	*/
-
-/*------------------------------------------------------------------------
- * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
- * and really doesn't need any additional clutter. So I choose the lazy
- * way out to avoid changes there -- define the base address to ensure
- * cache bypass so there's no need to monkey with inx/outx macros.
- *----------------------------------------------------------------------*/
-#define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
-#define CONFIG_NET_MULTI
-#define CONFIG_SMC91111			/* Using SMC91c111	*/
-#undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
-#define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
-
-#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_IPADDR		192.168.2.21
-#define CONFIG_SERVERIP		192.168.2.16
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_RUN
-#define CONFIG_CMD_SAVES
-
-
-/*------------------------------------------------------------------------
- * MISC
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP				/* Provide extended help*/
-#define CONFIG_SYS_PROMPT		"==> "		/* Command prompt	*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O buf size */
-#define CONFIG_SYS_MAXARGS		16		/* Max command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot arg buf size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE	/* Default load address */
-#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE	/* Start addr for test	*/
-#define CONFIG_SYS_MEMTEST_END		CONFIG_SYS_INIT_SP - 0x00020000
-
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-
-#endif	/* __CONFIG_H */

include/configs/EP1S40.h deleted +0 -207

deleted file mode 100644
index 4d905fe..0000000
@@ -1,207 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <[email protected]>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*------------------------------------------------------------------------
- * BOARD/CPU
- *----------------------------------------------------------------------*/
-#define CONFIG_EP1S40		1		/* EP1S40 board		*/
-#define CONFIG_SYS_CLK_FREQ	50000000	/* 50 MHz core clk	*/
-
-#define CONFIG_SYS_RESET_ADDR		0x00000000	/* Hard-reset address	*/
-#define CONFIG_SYS_EXCEPTION_ADDR	0x01000020	/* Exception entry point*/
-#define CONFIG_SYS_NIOS_SYSID_BASE	0x021208b8	/* System id address	*/
-
-/*------------------------------------------------------------------------
- * CACHE -- the following will support II/s and II/f. The II/s does not
- * have dcache, so the cache instructions will behave as NOPs.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_ICACHE_SIZE		4096		/* 4 KByte total	*/
-#define CONFIG_SYS_ICACHELINE_SIZE	32		/* 32 bytes/line	*/
-#define CONFIG_SYS_DCACHE_SIZE		2048		/* 2 KByte (II/f)	*/
-#define CONFIG_SYS_DCACHELINE_SIZE	4		/* 4 bytes/line (II/f)	*/
-
-/*------------------------------------------------------------------------
- * MEMORY BASE ADDRESSES
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE		0x00000000	/* FLASH base addr	*/
-#define CONFIG_SYS_FLASH_SIZE		0x00800000	/* 8 MByte		*/
-#define CONFIG_SYS_SDRAM_BASE		0x01000000	/* SDRAM base addr	*/
-#define CONFIG_SYS_SDRAM_SIZE		0x01000000	/* 16 MByte		*/
-#define CONFIG_SYS_SRAM_BASE		0x02000000	/* SRAM base addr	*/
-#define CONFIG_SYS_SRAM_SIZE		0x00100000	/* 1 MB			*/
-
-/*------------------------------------------------------------------------
- * MEMORY ORGANIZATION
- *	-Monitor at top.
- *	-The heap is placed below the monitor.
- *	-Global data is placed below the heap.
- *	-The stack is placed below global data (&grows down).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256k		*/
-#define CONFIG_SYS_GBL_DATA_SIZE	128		/* Global data size rsvd*/
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 256*1024) /* 256k heap */
-
-#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
-#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP		CONFIG_SYS_GBL_DATA_OFFSET
-
-/*------------------------------------------------------------------------
- * FLASH (AM29LV065D)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128		/* Max # sects per bank */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* Max # of flash banks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	8000		/* Erase timeout (msec) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	100		/* Write timeout (msec) */
-
-/*------------------------------------------------------------------------
- * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
- * CONFIG_SYS_FLASH_BASE, since we assume that u-boot is stored at the bottom
- * of flash memory. This will keep the environment in user region
- * of flash. NOTE: the monitor length must be multiple of sector size
- * (which is common practice).
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH	1		/* Environment in flash */
-#define CONFIG_ENV_SIZE		(64 * 1024)	/* 64 KByte (1 sector)	*/
-#define CONFIG_ENV_OVERWRITE			/* Serial change Ok	*/
-#define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
-
-/*------------------------------------------------------------------------
- * CONSOLE
- *----------------------------------------------------------------------*/
-#define CONFIG_ALTERA_UART		1	/* Use altera uart */
-#if defined(CONFIG_ALTERA_JTAG_UART)
-#define CONFIG_SYS_NIOS_CONSOLE	0x021208b0	/* JTAG UART base addr	*/
-#else
-#define CONFIG_SYS_NIOS_CONSOLE	0x02120840	/* UART base addr	*/
-#endif
-
-#define CONFIG_SYS_NIOS_FIXEDBAUD	1		/* Baudrate is fixed	*/
-#define CONFIG_BAUDRATE		115200		/* Initial baudrate	*/
-#define CONFIG_SYS_BAUDRATE_TABLE	{115200}	/* It's fixed ;-)	*/
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1		/* Suppress console info*/
-
-/*------------------------------------------------------------------------
- * EPCS Device -- None for stratix.
- *----------------------------------------------------------------------*/
-#undef CONFIG_SYS_NIOS_EPCSBASE
-
-/*------------------------------------------------------------------------
- * DEBUG
- *----------------------------------------------------------------------*/
-#undef CONFIG_ROM_STUBS				/* Stubs not in ROM	*/
-
-/*------------------------------------------------------------------------
- * TIMEBASE --
- *
- * The high res timer defaults to 1 msec. Since it includes the period
- * registers, the interrupt frequency can be reduced using TMRCNT.
- * If the default period is acceptable, TMRCNT can be left undefined.
- * TMRMS represents the desired mecs per tick (msecs per interrupt).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_HZ			1000	/* Always 1000 */
-#define CONFIG_SYS_NIOS_TMRBASE	0x02120820	/* Tick timer base addr */
-#define CONFIG_SYS_NIOS_TMRIRQ		3	/* Timer IRQ num */
-#define CONFIG_SYS_NIOS_TMRMS		10	/* Desired period (msec) */
-#define CONFIG_SYS_NIOS_TMRCNT \
-		(CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
-
-/*------------------------------------------------------------------------
- * STATUS LED -- Provides a simple blinking led. For Nios2 each board
- * must implement its own led routines -- since leds are board-specific.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LEDPIO_ADDR		0x02120870	/* LED PIO base addr	*/
-#define CONFIG_STATUS_LED			/* Enable status driver */
-
-#define STATUS_LED_BIT		1		/* Bit-0 on PIO		*/
-#define STATUS_LED_STATE	1		/* Blinking		*/
-#define STATUS_LED_PERIOD	(500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec	*/
-
-/*------------------------------------------------------------------------
- * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
- * and really doesn't need any additional clutter. So I choose the lazy
- * way out to avoid changes there -- define the base address to ensure
- * cache bypass so there's no need to monkey with inx/outx macros.
- *----------------------------------------------------------------------*/
-#define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
-#define CONFIG_NET_MULTI
-#define CONFIG_SMC91111			/* Using SMC91c111	*/
-#undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
-#define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
-
-#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
-#define CONFIG_NETMASK		255.255.255.0
-#define CONFIG_IPADDR		192.168.2.21
-#define CONFIG_SERVERIP		192.168.2.16
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_RUN
-#define CONFIG_CMD_SAVES
-
-
-/*------------------------------------------------------------------------
- * MISC
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP				/* Provide extended help*/
-#define CONFIG_SYS_PROMPT		"==> "		/* Command prompt	*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O buf size */
-#define CONFIG_SYS_MAXARGS		16		/* Max command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot arg buf size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE	/* Default load address */
-#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE	/* Start addr for test	*/
-#define CONFIG_SYS_MEMTEST_END		CONFIG_SYS_INIT_SP - 0x00020000
-
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-
-#endif	/* __CONFIG_H */