TOT u-boot makes P1020RDB unbootable
Hi,
I've tried to flash TOT u-boot complied with ELDK 4.2 for P1020_config into my P1020RDB RevD and bricked it. The same u-boot boots fine on P2020RDB revC.
I don't have BDI3000 at the moment to debug the problem. It would be great to fix it
before the release.
Below is u-boot output from P1020RDB running with u-boot-2009.11 from FSL BSP
U-Boot 2009.11-00001-g4458602-dirty (Feb 27 2010 - 11:13:42)
CPU0: P1020E, Version: 1.0, (0x80ec0010)
Core: E500, Version: 5.0, (0x80212050)
Clock Configuration:
CPU0:800 MHz, CPU1:800 MHz,
CCB:400 MHz,
DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:25 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: P1020RDB RevD
I2C: ready
SPI: ready
DRAM: Configuring DDR for 666.667 MT/s data rate
DDR: 512 MB
NOR Flash Bank : Primary
SD/MMC : 4-bit Mode
eSPI : Enabled
FLASH: 16 MB
L2: 256 KB enabled
NAND: 32 MiB
MMC: FSL_ESDHC: 0
EEPROM: Read failed.eTSEC2 is in sgmii mode.
PCIE2 connected to Slot 1 as Root Complex (base addr ffe09000) PCIE2 on bus 00 - 01
PCIE1 connected to Slot 2 as Root Complex (base addr ffe0a000) PCIE1 on bus 02 - 02
In: serial Out: serial Err: serial Net: uploading VSC7385 microcode from ef000000 eTSEC1: No support for PHY id ffffffff; assuming generic
eTSEC1, eTSEC2, eTSEC3
Thanks.
Felix.
There are few changes which need to be done for RevD and are not in TOT.
I will send the patches for it soon.
Regards
Poonam
Quoted 2 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de
[mailto:u-boot-bounces at lists.denx.de]
Quoted 7 lines
On Behalf Of Felix Radensky
Sent: Monday, June 21, 2010 3:49 PM
To: U-Boot-Denx; Kumar Gala
Subject: [U-Boot] TOT u-boot makes P1020RDB unbootableHi,
Quoted 8 lines
I've tried to flash TOT u-boot complied with ELDK 4.2 for
P1020_configinto my P1020RDB RevD and bricked it. The same u-boot boots fine on P2020RDB revC.I don't have BDI3000 at the moment to debug the problem. It would be great to fix it before the release.
Below is u-boot output from P1020RDB running with u-boot-2009.11 from
FSL
Quoted 31 lines
BSP
U-Boot 2009.11-00001-g4458602-dirty (Feb 27 2010 - 11:13:42)
CPU0: P1020E, Version: 1.0, (0x80ec0010) Core: E500, Version: 5.0, (0x80212050) Clock Configuration: CPU0:800 MHz, CPU1:800 MHz, CCB:400 MHz, DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:25 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: P1020RDB RevD I2C: ready SPI: ready DRAM: Configuring DDR for 666.667 MT/s data rate DDR: 512 MB NOR Flash Bank : Primary SD/MMC : 4-bit Mode eSPI : Enabled FLASH: 16 MB L2: 256 KB enabled NAND: 32 MiB MMC: FSL_ESDHC: 0 EEPROM: Read failed.eTSEC2 is in sgmii mode.
PCIE2 connected to Slot 1 as Root Complex (base addr
ffe09000) PCIE2 on bus 00 - 01
Quoted 8 lines
PCIE1 connected to Slot 2 as Root Complex (base addr
ffe0a000) PCIE1 on bus 02 - 02In: serial Out: serial Err: serial Net: uploading VSC7385 microcode from ef000000 eTSEC1: No support for PHY id ffffffff; assuming generic eTSEC1,
eTSEC2,
Quoted 10 lines
eTSEC3
Thanks.
Felix.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Dear "Aggrwal Poonam-B10812",
Quoted 3 lines · In message <8660DA277DC57B4BAAC78225F03146B6B08809@zin33exm24.fsl.freescale.net…
There are few changes which need to be done for RevD and are not in TOT.
I will send the patches for it soon.
Please hurry up. There is not much time left before the release.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "Beware of programmers carrying screwdrivers." - Chip Salzenberg
Quoted 4 lines
-----Original Message-----
From: u-boot-bounces at lists.denx.de
[mailto:u-boot-bounces at lists.denx.de]
Quoted 10 lines
On Behalf Of Wolfgang Denk
Sent: Monday, June 21, 2010 4:25 PM
To: Aggrwal Poonam-B10812
Cc: U-Boot-Denx; Kumar Gala
Subject: Re: [U-Boot] TOT u-boot makes P1020RDB unbootableDear "Aggrwal Poonam-B10812",
In message <8660DA277DC57B4BAAC78225F03146B6B08809@zin33exm24.fsl.freescale.net>
you
Quoted 8 lines
Quoted 1 line · wrote:
There are few changes which need to be done for RevD and are not in
TOT.
Quoted 2 lines
I will send the patches for it soon.
Please hurry up. There is not much time left before the release.
I am right now testing it, will send the patch ASAP.
Regards
Poonam
Quoted 13 lines
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Beware of programmers carrying screwdrivers." - Chip Salzenberg
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot