Skip to contentSkip to conversation

kernel 2.6.32-5-parisc64 doesn't boot

DISCUSSION Grant Grundler 1 participant 1 message Jun 29, 2010 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

Grant Grundler

author
#1 lore raw

+linux-parisc (seems like a known kernel issue)

Quoted 6 lines · Michal Ludvig

Hi all,

After recent dist-upgrade in Squeeze my HP9000 RP3410 no longer boots. I can still boot the previous linux-image 2.6.32-3-parisc64 but the new 2.6.32-5-parisc64 never finished booting. It looks like it reboots during USB enumeration or somewhere there:

Hi Michal,
I strongly suspect it's the same problem we saw on the C3xxx workstations. Here's the comment in drivers/parisc/sba_iommu.c:

if (!is_pdc_pat()) {
/* Shutdown the USB controller on Astro-based workstations. ** Once we reprogram the IOMMU, the next DMA performed by ** USB will HPMC the box. USB is only enabled if a ** keyboard is present and found.
**
** With serial console, j6k v5.0 firmware says:
** mem_kbd hpa 0xfee003f8 sba 0x0 pad 0x0 cl_class 0x7
**
** FIXME: Using GFX+USB console at power up but direct
** linux to serial console is still broken.
** USB could generate DMA so we must reset USB.
** The proper sequence would be:
** o block console output
** o reset USB device
** o reprogram serial port
** o unblock console output
*/
if (PAGE0->mem_kbd.cl_class == CL_KEYBD) {
pdc_io_reset_devices();
}

}

Could you try to make this code "unconditional"?
(remove !is_pdc_pat() test)

If someone have better ideas on how to handle this... I can build kernels and test on a J6000.

thanks,
grant

Quoted 281 lines

------------------------------------

Booting...
Boot IO Dependent Code (IODC) revision 1

HARD Booted.
palo ipl 1.14 root@penalosa Wed Oct 8 15:04:37 UTC 2008 Skipping extended partition 6 - beyond reach of IPL

Partition Start(MB) End(MB) Id Type

1               1      31   f0 Palo
2              32     156   83 ext2
5             157   33408   83 ext2

PALO(F0) partition contains:

    0/vmlinux64 6833698 bytes @ 0x48000

Command line for kernel: 'root=/dev/sdb5 HOME=/ console=ttyS1 palo_kernel=2/vmlinux'
Selected kernel: /vmlinux from partition 2
Selected ramdisk: /initrd.img from partition 2
ELF64 executable
Entry 00100000 first 00100000 n 2
Segment 0 load 00100000 size 4673536 mediaptr 0x1000
Segment 1 load 005ea730 size 743376 mediaptr 0x476730 Loading ramdisk 11788317 bytes @ 3f4b0000...
Branching to kernel entry point 0x00100000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at parisc-linux.org

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-5-parisc64 (Debian 2.6.32-15)
([email protected]) (gcc version 4.3.5 (GCC) ) #1 Tue Jun 1 12:13:09
UTC 2010
[    0.000000] unwind_init: start = 0x40494000, end = 0x404c1e60,
entries = 11750
[    0.000000] WARNING: Out of order unwind entry! 0000000040495990 and
00000000404959a0
[    0.000000] WARNING: Out of order unwind entry! 00000000404959a0 and
00000000404959b0
[    0.000000] FP[0] enabled: Rev 1 Model 20
[    0.000000] The 64-bit Kernel has started...
[    0.000000] bootconsole [ttyB0] enabled
[    0.000000] Initialized PDC Console for debugging.
[    0.000000] Determining PDC firmware type: 64 bit PAT.
[    0.000000] model 00008860 00000491 00000000 00000002
3e3ffb8ecde69d7c 100000f0 00000008 000000b2 000000b2
[    0.000000] vers  00000302
[    0.000000] CPUID vers 20 rev 5 (0x00000285)
[    0.000000] capabilities 0x35
[    0.000000] model 9000/800/rp3410
[    0.000000] parisc_cache_init: Only equivalent aliasing supported!
[    0.000000] Memory Ranges:
[    0.000000]  0) Start 0x0000000000000000 End 0x000000003fffffff Size
  1024 MB
[    0.000000]  1) Start 0x0000004040000000 End 0x00000040ffdfffff Size
  3070 MB
[    0.000000] Total Memory: 4094 MB
[    0.000000] initrd: 7f4b0000-7ffee01d
[    0.000000] initrd: reserving 3f4b0000-3ffee01d (mem_max ffe00000)
[    0.000000] Built 2 zonelists in Zone order, mobility grouping on.
Total pages: 1033735
[    0.000000] Kernel command line: root=/dev/sdb5 HOME=/ console=ttyS1
palo_kernel=2/vmlinux
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10,
4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152
bytes)
[    0.000000] Memory: 4102144k/4192256k available (2996k kernel code,
89144k reserved, 1519k data, 272k init)
[    0.000000] virtual kernel memory layout:
[    0.000000]     vmalloc : 0x0000000000008000 - 0x000000003f000000
(1007 MB)
[    0.000000]     memory  : 0x0000000040000000 - 0x000000413fe00000
(266238 MB)
[    0.000000]       .init : 0x000000004065c000 - 0x00000000406a0000   (
272 kB)
[    0.000000]       .data : 0x00000000403ed080 - 0x0000000040568de0
(1519 kB)
[    0.000000]       .text : 0x0000000040100000 - 0x00000000403ed080
(2996 kB)
[    0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0,
CPUs=1, Nodes=8
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 160x64
[    0.012000] Calibrating delay loop... 1597.44 BogoMIPS (lpj=3194880)
[    0.108000] Security Framework initialized
[    0.108000] SELinux:  Disabled at boot.
[    0.108000] Mount-cache hash table entries: 256
[    0.108000] Initializing cgroup subsys ns
[    0.108000] Initializing cgroup subsys cpuacct
[    0.112000] Initializing cgroup subsys devices
[    0.116000] Initializing cgroup subsys freezer
[    0.120000] Initializing cgroup subsys net_cls
[    0.120000] devtmpfs: initialized
[    0.128000] regulator: core version 0.5
[    0.128000] NET: Registered protocol family 16
[    0.132000] EISA bus registered
[    0.136000] Searching for devices...
[    0.356000] Found devices:
[    0.356000] 1. Storm Peak Slow DC- at 0xfffffffffe780000 [128] { 0,
0x0, 0x886, 0x00004 }
[    0.356000] 2. Everest Mako Memory at 0xfffffffffed08000 [8] { 1,
0x0, 0x0af, 0x00009 }
[    0.356000] 3. Pluto BC McKinley Port at 0xfffffffffed00000 [0] { 12,
0x0, 0x880, 0x0000c }
[    0.364000] 4. Mercury PCI Bridge at 0xfffffffffed20000 [0/0] { 13,
0x0, 0x783, 0x0000a }
[    0.372000] 5. Mercury PCI Bridge at 0xfffffffffed22000 [0/1] { 13,
0x0, 0x783, 0x0000a }
[    0.376000] 6. Mercury PCI Bridge at 0xfffffffffed24000 [0/2] { 13,
0x0, 0x783, 0x0000a }
[    0.384000] 7. Mercury PCI Bridge at 0xfffffffffed26000 [0/3] { 13,
0x0, 0x783, 0x0000a }
[    0.392000] 8. Mercury PCI Bridge at 0xfffffffffed28000 [0/4] { 13,
0x0, 0x783, 0x0000a }
[    0.392000] 9. Mercury PCI Bridge at 0xfffffffffed2c000 [0/6] { 13,
0x0, 0x783, 0x0000a }
[    0.400000] 10. Mercury PCI Bridge at 0xfffffffffed2e000 [0/7] { 13,
0x0, 0x783, 0x0000a }
[    0.408000] 11. BMC IPMI Mgmt Ctlr at 0xfffffff0f05b0000 [16] { 15,
0x0, 0x004, 0x000c0 }
[    0.412000] Enabling PDC_PAT chassis codes support v0.05
[    1.268000] CPU(s): 1 x PA8800 (Mako) at 800.024500 MHz
[    1.272000] Setting cache flush threshold to 135cec0 (1 CPUs online)
[    1.324000] SBA found Pluto 2.3 at 0xfffffffffed00000
[    1.384000] Mercury version TR3.2 (0x32) found at 0xfffffffffed20000
[    1.420000] pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot
[    1.420000] pci 0000:00:01.0: PME# disabled
[    1.420000] pci 0000:00:01.1: PME# supported from D0 D1 D2 D3hot
[    1.420000] pci 0000:00:01.1: PME# disabled
[    1.432000] pci 0000:00:01.2: PME# supported from D0 D1 D2 D3hot
[    1.432000] pci 0000:00:01.2: PME# disabled
[    1.448000] Mercury version TR3.2 (0x32) found at 0xfffffffffed22000
[    1.484000] pci 0000:20:02.0: PME# supported from D3hot D3cold
[    1.488000] pci 0000:20:02.0: PME# disabled
[    1.492000] Mercury version TR3.2 (0x32) found at 0xfffffffffed24000
[    1.536000] Mercury version TR3.2 (0x32) found at 0xfffffffffed26000
[    1.584000] Mercury version TR3.2 (0x32) found at 0xfffffffffed28000
[    1.632000] Mercury version TR3.2 (0x32) found at 0xfffffffffed2c000
[    1.680000] Mercury version TR3.2 (0x32) found at 0xfffffffffed2e000
[    1.720000] LBA: Truncating lmmio_space
[fffffffff0000000/fffffffffecffffe] to [fffffffff0000000,fffffffffe77ffff]
[    1.724000] powersw: Soft power switch support not available.
[    1.728000] bio: create slab <bio-0> at 0
[    1.728000] vgaarb: device added:
PCI:0000:e0:02.0,decodes=io+mem,owns=io+mem,locks=none
[    1.728000] vgaarb: loaded
[    1.736000] Switching to clocksource cr16
[    1.736000] NET: Registered protocol family 2
[    1.736000] IP route cache hash table entries: 131072 (order: 8,
1048576 bytes)
[    1.744000] TCP established hash table entries: 262144 (order: 10,
4194304 bytes)
[    1.756000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    1.760000] TCP: Hash tables configured (established 262144 bind 65536)
[    1.760000] TCP reno registered
[    1.764000] NET: Registered protocol family 1
[    1.788000] Unpacking initramfs...
[    2.532000] Freeing initrd memory: 11512k freed
[    2.536000] Chassis warnings not supported.
[    2.536000] Performance monitoring counters enabled for Storm Peak
Slow DC-
[    2.536000] audit: initializing netlink socket (disabled)
[    2.540000] type=2000 audit(1277259537.537:1): initialized
[    2.552000] VFS: Disk quotas dquot_6.5.2
[    2.552000] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    2.560000] msgmni has been set to 8036
[    2.560000] alg: No test for stdrng (krng)
[    2.560000] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[    2.564000] io scheduler noop registered
[    2.564000] io scheduler anticipatory registered
[    2.572000] io scheduler deadline registered
[    2.572000] io scheduler cfq registered (default)
[    2.584000] PDC Stable Storage facility v0.30
[    2.672000] STI GSC/PCI core graphics driver Version 0.9a
[    2.676000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.684000] 0000:e0:01.0: ttyS0 at MMIO 0xfffffffff4051000 (irq = 74)
is a 16450
[    2.692000] 0000:e0:01.1: ttyS1 at MMIO 0xfffffffff4050000 (irq = 74)
is a 16550A
[    2.692000] console [ttyS1] enabled, bootconsole disabled
[    2.692000] console [ttyS1] enabled, bootconsole disabled
[    2.696000] 0000:e0:01.1: ttyS2 at MMIO 0xfffffffff4050010 (irq = 74)
is a 16550A
[    2.704000] 0000:e0:01.1: ttyS3 at MMIO 0xfffffffff4050038 (irq = 74)
is a 16550A
[    2.712000] mice: PS/2 mouse device common for all mice
[    2.712000] rtc-generic rtc-generic: rtc core: registered rtc-generic
as rtc0
[    2.720000] TCP cubic registered
[    2.720000] NET: Registered protocol family 17
[    2.724000] registered taskstats version 1
[    2.740000] rtc-generic rtc-generic: setting system clock to
2010-06-23 02:18:58 UTC (1277259538)
[    2.916000] Freeing unused kernel memory: 272k freed
Loading, please wait...
[    3.580000] udev: starting version 157
[    4.492000] SCSI subsystem initialized
[    4.692000] usbcore: registered new interface driver usbfs
[    4.692000] usbcore: registered new interface driver hub
[    4.692000] usbcore: registered new device driver usb
[    4.940000] tg3.c:v3.102 (September 1, 2009)
[    5.016000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.044000] ehci_hcd 0000:00:01.2: EHCI Host Controller
[    5.064000] ehci_hcd 0000:00:01.2: new USB bus registered, assigned
bus number 1
[    5.088000] ehci_hcd 0000:00:01.2: Enabling legacy PCI PM
[    5.112000] ehci_hcd 0000:00:01.2: irq 67, io mem 0xffffffff80000000
[    5.128000] ehci_hcd 0000:00:01.2: USB 2.0 started, EHCI 0.95
[    5.128000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    5.128000] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[    5.136000] usb usb1: Product: EHCI Host Controller
[    5.136000] usb usb1: Manufacturer: Linux 2.6.32-5-parisc64 ehci_hcd
[    5.144000] usb usb1: SerialNumber: 0000:00:01.2
[    5.196000] usb usb1: configuration #1 chosen from 1 choice
[    5.196000] hub 1-0:1.0: USB hub found
[    5.196000] hub 1-0:1.0: 5 ports detected

Firmware Version 46.34

Duplex Console IO Dependent Code (IODC) revision 1

Firmware Version 46.34

Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2004, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

  Processor   Speed            State           CoProcessor State  Cache Size
  Number                                       State              Inst

Data
--------- -------- --------------------- -----------------
------------
0 800 MHz Active Functional
33554432 33554432
1 800 MHz Stopped:Deconfigured Unknown 0 0

  Central Bus Speed (in MHz)  :        200
  Available Memory            :    4194304  KB
  Good Memory Required        : Not initialized. Defaults to 32 MB.
   Primary boot path:    0/1/1/0.1
   Alternate boot path:  0/1/1/0.0
   Console path:         0/7/1/1.0
   Keyboard path:        0/0/4/0.0

Processor is booting from the first available device.

To discontinue, press any key within 10 seconds.

Boot terminated.

------------------------------------

It kept trying and failing/rebooting at the same point a couple of times.

Do you need any other information? I'm now back on 2.6.32-3 but am keen to run any test kernels.

Michal

Signature · 3 lines
To UNSUBSCRIBE, email to [email protected]
with a subject of "unsubscribe". Trouble? Contact [email protected]
Archive: http://lists.debian.org/[email protected]