Handling dual die and single die flash on same board
Hi,
I've run into a situation with a new design and I could use some pointers.
Our hardware designers have built prototypes with different flash configurations. One possible configuration is a dual die 2x32MB the other is a single die 1x64MB.
My u-boot config is currently setup for the 2x32MB case i.e. CONFIG_SYS_MAX_FLASH_BANKS = 2, CONFIG_SYS_FLASH_BANKS_LIST = {base, base+32MB}. The problem with this is that when flash_get_size is called on the 1x64 chip it discovers the same chip the 2nd time around and promptly walks off the end of the memory area I have allocated for it.
Is there any existing way to make the cfi_flash driver handle this situation for me?
Thanks,
Chris Packham
Hi Chris,
Quoted 6 lines · On Tuesday 07 September 2010 19:05:46 Chris Packham wrote:
I've run into a situation with a new design and I could use some pointers.
Our hardware designers have built prototypes with different flash configurations. One possible configuration is a dual die 2x32MB the other is a single die 1x64MB.
Quoted 8 lines
My u-boot config is currently setup for the 2x32MB case i.e.
CONFIG_SYS_MAX_FLASH_BANKS= 2,CONFIG_SYS_FLASH_BANKS_LIST= {base, base+32MB}. The problem with this is that whenflash_get_sizeis called on the 1x64 chip it discovers the same chip the 2nd time around and promptly walks off the end of the memory area I have allocated for it.Is there any existing way to make the
cfi_flashdriver handle this situation for me?
I just recently sent a patchset for the CFI driver that could help to handle such a situation. Here the most interesting patch:
http://www.mail-archive.com/u-boot at lists.denx.de/msg37234.html
I would suggest to set CONFIG_SYS_MAX_FLASH_BANKS_DETECT to 2 and then add some board specific code to determine the real bank count and set cfi_flash_num_flash_banks accordingly.
Hope this helps.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
Quoted 12 lines · Stefan Roese
Hi Chris,
Quoted 8 lines · On Tuesday 07 September 2010 19:05:46 Chris Packham wrote:
My u-boot config is currently setup for the 2x32MB case i.e.
CONFIG_SYS_MAX_FLASH_BANKS= 2,CONFIG_SYS_FLASH_BANKS_LIST= {base, base+32MB}. The problem with this is that whenflash_get_sizeis called on the 1x64 chip it discovers the same chip the 2nd time around and promptly walks off the end of the memory area I have allocated for it.Is there any existing way to make the
cfi_flashdriver handle this situation for me?
Quoted 9 lines
I just recently sent a patchset for the CFI driver that could help to handle such a situation. Here the most interesting patch:
http://www.mail-archive.com/u-boot at lists.denx.de/msg37234.html
I would suggest to set
CONFIG_SYS_MAX_FLASH_BANKS_DETECTto 2 and then add some board specific code to determine the real bank count and setcfi_flash_num_flash_banksaccordingly.
Thanks for the pointers. For now I've followed the example in tqm834x.c. I've done it in such a way that when we next pull in upstream u-boot it should co-exists nicely with your proposed patch.