Skip to contentSkip to conversation

Loading u-boot from SD/MMC (was Re: [PATCH v3] AT91: MCI: add SD/MMC driver using mmc framework)

U-Boot Reinhard Meyer 2 participants 2 messages Sep 7, 2010 – Sep 8, 2010

lore
Share & tools
lore
#0 lore raw

Dear Will Tucker,

Quoted 8 lines

Hi,

I?m trying to get the ATSAM9G20-EK booting from SD/MMC on MCI A, with the Nand and Dataflash disabled, with no luck.

I have gotten the latest u-boot-atmel compiled and placed boot.bin on a FAT 16 formatted. When I turn power on I only get RomBoot on the debug uart.

Quoted 9 lines

1) Do I need to use the latest AT91Bootstrap, I have v1.16 but do not see any way to enable the mci

If I need an update where can I get the latest version?

Any help would be appreciated,

Will Tucker

First, please observe the following:
1. Start a new thread for comments/questions unrelated to the existing thread.
2. Always post the u-boot mailing list as well.
3. Please make your lines wrap at less than 80 characters.

To give a brief answer to your issue:

Please study sections 8 and 13 of the 9G20 datasheet. As a result you will see that the ROM will try to load "boot.bin" to internal SRAM. This will limit the image size to 16K. Apparently that cannot be u-boot itself. This 16k code would need to initialize SDRAM and load another, larger file (e.g. u-boot.bin) from SD/MMC into SDRAM. I don't know whether AT91Bootstrap sources already handle such a situation. Latest Versions you will find on the Atmel Website.

Please note that this is not an u-boot issue.

The patch "SD/MMC support" for u-boot enables to access SD/MMC from u-boot ONCE it is running.

Best Regards,
Reinhard

#1 lore raw

Running U-Boot from the SDCard on an Atmel 9G20 is certainly doable. I have recently booted U-Boot and Linux from an SDCard on an Atmel AT91SAM9G45-EKES with no other non-volatile memories and the process is the same with some minor limitations.

The process I used:
1. SAM Boot loader loads "boot.bin" from the first FAT partition
2. Boot.bin loads U-Boot from "uboot.bin" into high DRAM
3. Boot.bin loads a uImage file lower into DRAM
4. Boot.bin jumps into U-Boot
4. U-Boot's boot command boots the image my boot.bin leaves lying around in DRAM.

I started with Atmel's SDCard bootstrap example and modified it to load both U-Boot and a Linux image into RAM then jump to U-Boot. The U-Boot and the Linux uImage were "stock" builds with no special features. Once the SD/MMC U-Boot patches make it into the mainline I expect to let U-Boot read the Linux image from the SDCard.

The 9G20 has two limitations that I know of:
1. 9G20's boot ROM doesn't support SDHC cards (> 2GB)
2. 9G20's SRAM that boot.bin loads into is 16K which may be too tight for a full FAT handler.

The 9G45 has 64K of SRAM so the boot.bin program I used has a full FAT file system handler. Start by looking at the 9G20 "AT91 Software package" at http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4343 and dive into the SD/MMC examples.

The SD/MMC patches for AT91 will make this a lot simpler.

Enjoy,
Bill.

Quoted 54 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot- bounces at lists.denx.de] On Behalf Of Reinhard Meyer
Sent: Tuesday, September 07, 2010 6:40 PM
To: Will Tucker; u-boot at lists.denx.de
Subject: [U-Boot] Loading u-boot from SD/MMC (was Re: [PATCH v3] AT91:
MCI: add SD/MMC driver using mmc framework)

Dear Will Tucker,

Quoted 3 lines

Hi,

I'm trying to get the ATSAM9G20-EK booting from SD/MMC on MCI A, with

the Nand > and Dataflash disabled, with no luck.

Quoted 2 lines

I have gotten the latest u-boot-atmel compiled and placed boot.bin on a

FAT 16 > formatted. When I turn power on I only get RomBoot on the debug uart.

Quoted 2 lines

1) Do I need to use the latest AT91Bootstrap, I have v1.16 but do not see

any > way to enable the mci > > If I need an update where can I get the latest version?

Quoted 5 lines

Any help would be appreciated,

Will Tucker

First, please observe the following:
1. Start a new thread for comments/questions unrelated to the existing thread.
2. Always post the u-boot mailing list as well.
3. Please make your lines wrap at less than 80 characters.

To give a brief answer to your issue:

Please study sections 8 and 13 of the 9G20 datasheet. As a result you will see that the ROM will try to load "boot.bin" to internal SRAM. This will limit the image size to 16K. Apparently that cannot be u-boot itself. This 16k code would need to initialize SDRAM and load another, larger file (e.g. u-boot.bin) from SD/MMC into SDRAM. I don't know whether AT91Bootstrap sources already handle such a situation. Latest Versions you will find on the Atmel Website.

Please note that this is not an u-boot issue.

The patch "SD/MMC support" for u-boot enables to access SD/MMC from u- boot ONCE it is running.

Best Regards,
Reinhard
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot