PHY/FEC Network adapter failed to initialize on MPC52xx Board
Hi all
I got completely stuck with a network adapter problem on my ppc board (MPC52xx style). The ntwork adapter does not seem to intialize correctly when booted without 'help from uboot'
The adapter works properly when I first use it with uboot. E.g. using tftp to load the kernel or just issuing a dummy sntp command. It does not get intialized if I boot linux without using any network relevant command in ubboot
The difference manifests on the boot message: (working) PHY working
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:
device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2,
host=192.168.1.245, domain=, nis-domain=(none),
bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=Looking up port of RPC 100003/2 on 192.168.1.244 Looking up port of RPC 100005/1 on 192.168.1.244
VFS: Mounted root (nfs filesystem) on device 0:11. Freeing unused kernel memory: 124k init
PHY: f0003000:00 - Link is Up - 100/Full
# ping 192.168.1.2 returns proper results.
PHY Not working:
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:
device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2,
host=192.168.1.245, domain=, nis-domain=(none),
bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 124k init
# ping 192.168.1.2 hangs
The second snipped does not have "Looking up.." messages because it boots from flash. Main difference is "PHY: f0003000:00 - Link is Up - 100/Full" which does not appear at the failing case.
Linux Version is 2.6.35.7 patched with xenomai 2.5 U-Boot 2010.06 (Aug 05 2010 - 19:54:45)
Linux configuration see below: ( i left most entries out that are not set) I also experimented with different settings but finally only CONFIG_FEC_MPC52xx=y and CONFIG_FEC_MPC52xx_MDIO=y
seem to be of any relevance. If both are set, the adapter works when initialized by uboot.
Any help or tips will be very much appreciated,
Regards, Peter
Linux .config
...
#
# Platform support
#
# CONFIG_PPC_CHRP is not set
# CONFIG_MPC5121_ADS is not set
# CONFIG_MPC5121_GENERIC is not set
CONFIG_PPC_MPC52xx=yCONFIG_PPC_MPC5200_SIMPLE=y
# CONFIG_PPC_EFIKA is not setCONFIG_PPC_LITE5200=y
# CONFIG_PPC_MEDIA5200 is not setCONFIG_PPC_MPC5200_BUGFIX=y
# CONFIG_PPC_MPC5200_GPIO is not setCONFIG_PPC_MPC5200_LPBFIFO=y
CONFIG_PPC_BESTCOMM=yCONFIG_PPC_BESTCOMM_FEC=yCONFIG_PPC_BESTCOMM_GEN_BD=y
# CONFIG_SIMPLE_GPIO is not set
..
# Bus options
#CONFIG_ZONE_DMA=yCONFIG_NEED_SG_DMA_LENGTH=yCONFIG_GENERIC_ISA_DMA=yCONFIG_PPC_PCI_CHOICE=y
...
#
# Generic Driver Options
#CONFIG_STANDALONE=yCONFIG_PREVENT_FIRMWARE_BUILD=yCONFIG_MTD=yCONFIG_MTD_PARTITIONS=yCONFIG_MTD_CMDLINE_PARTS=y
#
# MII PHY device drivers
#CONFIG_LXT_PHY=y ## Does not seem to have any influenceCONFIG_NET_ETHERNET=yCONFIG_MII=yCONFIG_ETHOC=y ## Does not seem to have any influence
CONFIG_FEC_MPC52xx=y ## Must be Y in roder to get adapter working with uboot's init
CONFIG_FEC_MPC52xx_MDIO=y ## Must be Y in roder to get adapter working with uboot's init
Quoted 51 lines · Peter
Hi all
I got completely stuck with a network adapter problem on my ppc board (MPC52xx style). The ntwork adapter does not seem to intialize correctly when booted without 'help from uboot'
The adapter works properly when I first use it with uboot. E.g. using tftp to load the kernel or just issuing a dummy sntp command. It does not get intialized if I boot linux without using any network relevant command in ubboot
The difference manifests on the boot message: (working) PHY working
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2, host=192.168.1.245, domain=, nis-domain=(none), bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=Looking up port of RPC 100003/2 on 192.168.1.244 Looking up port of RPC 100005/1 on 192.168.1.244
VFS: Mounted root (nfs filesystem) on device 0:11. Freeing unused kernel memory: 124k init
PHY: f0003000:00 - Link is Up - 100/Full# ping 192.168.1.2 returns proper results.PHY Not working:
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2, host=192.168.1.245, domain=, nis-domain=(none), bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 124k init
# ping 192.168.1.2 hangsThe second snipped does not have "Looking up.." messages because it boots from flash. Main difference is "PHY: f0003000:00 - Link is Up - 100/Full" which does not appear at the failing case.
Linux Version is 2.6.35.7 patched with xenomai 2.5 U-Boot 2010.06 (Aug 05 2010 - 19:54:45)
Quoted 7 lines
Linux configuration see below: ( i left most entries out that are not set) I also experimented with different settings but finally only CONFIG_FEC_MPC52xx=y and CONFIG_FEC_MPC52xx_MDIO=y
seem to be of any relevance. If both are set, the adapter works when initialized by uboot.Any help or tips will be very much appreciated,
There are a couple of possibilities:
* Many PHY devices will have an external RESET or enable pin which is driven by GPIO. The board support package in U-Boot for your board would then enable the PHY device as part of network initialization. The Linux kernel typically does not fiddle with such things.
* The actual PHY device may need some setup (adjustment of internal PHY registers) before it will come on-line, e.g. the device may not be strapped to auto-negotiate on the wire to find a link. U-Boot might be turning this on, or even forcing the link up (I've seen such devices that needed this level of hand-holding). Again, the Linux network driver typically will not be doing these sort of operations.
To figure out what's going on and what else you might need, you should look at both the U-Boot code for your board and the board documentation (schematics, etc). Then you should be able to see what U-Boot does that the Linux kernel is not. In the end, you may need to add some code in your target platform support in Linux to add the additional stuff to make the PHY work.
Quoted 55 lines
Linux .config
...
#
# Platform support
#
#CONFIG_PPC_CHRPis not set
#CONFIG_MPC5121_ADSis not set
#CONFIG_MPC5121_GENERICis not set
CONFIG_PPC_MPC52xx=yCONFIG_PPC_MPC5200_SIMPLE=y
#CONFIG_PPC_EFIKAis not setCONFIG_PPC_LITE5200=y
#CONFIG_PPC_MEDIA5200is not setCONFIG_PPC_MPC5200_BUGFIX=y
#CONFIG_PPC_MPC5200_GPIOis not setCONFIG_PPC_MPC5200_LPBFIFO=y
CONFIG_PPC_BESTCOMM=yCONFIG_PPC_BESTCOMM_FEC=yCONFIG_PPC_BESTCOMM_GEN_BD=y
#CONFIG_SIMPLE_GPIOis not set
..
# Bus options
#CONFIG_ZONE_DMA=yCONFIG_NEED_SG_DMA_LENGTH=yCONFIG_GENERIC_ISA_DMA=yCONFIG_PPC_PCI_CHOICE=y
...
#
# Generic Driver Options
#CONFIG_STANDALONE=yCONFIG_PREVENT_FIRMWARE_BUILD=yCONFIG_MTD=yCONFIG_MTD_PARTITIONS=yCONFIG_MTD_CMDLINE_PARTS=y#
# MII PHY device drivers
#CONFIG_LXT_PHY=y## Does not seem to have any influenceCONFIG_NET_ETHERNET=yCONFIG_MII=yCONFIG_ETHOC=y## Does not seem to have any influence
CONFIG_FEC_MPC52xx=y ## Must be Y in roder to get adapter working with uboot's init
CONFIG_FEC_MPC52xx_MDIO=y ## Must be Y in roder to get adapter working with uboot's init_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://lists.ozlabs.org/listinfo/linuxppc-dev
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Quoted 6 lines · Peter
Hi all
I got completely stuck with a network adapter problem on my ppc board (MPC52xx style). The ntwork adapter does not seem to intialize correctly when booted without 'help from uboot'
Looks your problem is very similar to one I replied here not long ago :) That is also issued from MPC5200. And I remember there was a wrong Port Multiplex Configuration.
If possible maybe you can check the email subjected "Problem Ethernet Initialization MPC5200 + LXT971A" on linuxppc-dev list.
Hope its useful.
Tiejun
Quoted 104 lines
The adapter works properly when I first use it with uboot. E.g. using tftp to load the kernel or just issuing a dummy sntp command. It does not get intialized if I boot linux without using any network relevant command in ubboot
The difference manifests on the boot message: (working) PHY working
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2, host=192.168.1.245, domain=, nis-domain=(none), bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=Looking up port of RPC 100003/2 on 192.168.1.244 Looking up port of RPC 100005/1 on 192.168.1.244
VFS: Mounted root (nfs filesystem) on device 0:11. Freeing unused kernel memory: 124k init
PHY: f0003000:00 - Link is Up - 100/Full# ping 192.168.1.2 returns proper results.PHY Not working:
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2, host=192.168.1.245, domain=, nis-domain=(none), bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 124k init
# ping 192.168.1.2 hangsThe second snipped does not have "Looking up.." messages because it boots from flash. Main difference is "PHY: f0003000:00 - Link is Up - 100/Full" which does not appear at the failing case.
Linux Version is 2.6.35.7 patched with xenomai 2.5 U-Boot 2010.06 (Aug 05 2010 - 19:54:45)
Linux configuration see below: ( i left most entries out that are not set) I also experimented with different settings but finally only CONFIG_FEC_MPC52xx=y and CONFIG_FEC_MPC52xx_MDIO=y
seem to be of any relevance. If both are set, the adapter works when initialized by uboot.Any help or tips will be very much appreciated,
Regards, Peter
Linux .config
...
#
# Platform support
#
#CONFIG_PPC_CHRPis not set
#CONFIG_MPC5121_ADSis not set
#CONFIG_MPC5121_GENERICis not set
CONFIG_PPC_MPC52xx=yCONFIG_PPC_MPC5200_SIMPLE=y
#CONFIG_PPC_EFIKAis not setCONFIG_PPC_LITE5200=y
#CONFIG_PPC_MEDIA5200is not setCONFIG_PPC_MPC5200_BUGFIX=y
#CONFIG_PPC_MPC5200_GPIOis not setCONFIG_PPC_MPC5200_LPBFIFO=y
CONFIG_PPC_BESTCOMM=yCONFIG_PPC_BESTCOMM_FEC=yCONFIG_PPC_BESTCOMM_GEN_BD=y
#CONFIG_SIMPLE_GPIOis not set
..
# Bus options
#CONFIG_ZONE_DMA=yCONFIG_NEED_SG_DMA_LENGTH=yCONFIG_GENERIC_ISA_DMA=yCONFIG_PPC_PCI_CHOICE=y
...
#
# Generic Driver Options
#CONFIG_STANDALONE=yCONFIG_PREVENT_FIRMWARE_BUILD=yCONFIG_MTD=yCONFIG_MTD_PARTITIONS=yCONFIG_MTD_CMDLINE_PARTS=y#
# MII PHY device drivers
#CONFIG_LXT_PHY=y## Does not seem to have any influenceCONFIG_NET_ETHERNET=yCONFIG_MII=yCONFIG_ETHOC=y## Does not seem to have any influence
CONFIG_FEC_MPC52xx=y ## Must be Y in roder to get adapter working with uboot's init
CONFIG_FEC_MPC52xx_MDIO=y ## Must be Y in roder to get adapter working with uboot's init
Tanks to all for the reply to this thread. I got the tip from the thread Tiejun mentioned.
Quotation: 'St. Strobel' in Xenomai-help
"I had this problem too. In my case the problem was caused by an incorrect port multiplex configuration in U-Boot, see CONIFG_SYS_GPS_PORT_CONFIG (I use 0x xxx5xxxx, which corresponds to 10/100Mbit Eth with MD). "
That fixed it for me.
Regards, Peter
Am 29.11.2010 03:48, schrieb tiejun.chen:
Quoted 126 lines
Quoted 6 lines · Peter
Hi all
I got completely stuck with a network adapter problem on my ppc board (MPC52xx style). The ntwork adapter does not seem to intialize correctly when booted without 'help from uboot'
Looks your problem is very similar to one I replied here not long ago :) That is also issued from MPC5200. And I remember there was a wrong Port Multiplex Configuration.
If possible maybe you can check the email subjected "Problem Ethernet Initialization MPC5200 + LXT971A" on linuxppc-dev list.
Hope its useful.
Tiejun
Quoted 95 lines
The adapter works properly when I first use it with uboot. E.g. using tftp to load the kernel or just issuing a dummy sntp command. It does not get intialized if I boot linux without using any network relevant command in ubboot
The difference manifests on the boot message: (working) PHY working
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2, host=192.168.1.245, domain=, nis-domain=(none), bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=Looking up port of RPC 100003/2 on 192.168.1.244 Looking up port of RPC 100005/1 on 192.168.1.244
VFS: Mounted root (nfs filesystem) on device 0:11. Freeing unused kernel memory: 124k init
PHY: f0003000:00 - Link is Up - 100/Full# ping 192.168.1.2 returns proper results.PHY Not working:
...
mpc52xx MII bus: probed
TCP cubic registered
NET: Registered protocol family 17
IP-Config: Complete:device=eth0, addr=192.168.1.245, mask=255.254.0.0, gw=192.168.1.2, host=192.168.1.245, domain=, nis-domain=(none), bootserver=192.168.1.244, rootserver=192.168.1.244, rootpath=VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 124k init
# ping 192.168.1.2 hangsThe second snipped does not have "Looking up.." messages because it boots from flash. Main difference is "PHY: f0003000:00 - Link is Up - 100/Full" which does not appear at the failing case.
Linux Version is 2.6.35.7 patched with xenomai 2.5 U-Boot 2010.06 (Aug 05 2010 - 19:54:45)
Linux configuration see below: ( i left most entries out that are not set) I also experimented with different settings but finally only CONFIG_FEC_MPC52xx=y and CONFIG_FEC_MPC52xx_MDIO=y
seem to be of any relevance. If both are set, the adapter works when initialized by uboot.Any help or tips will be very much appreciated,
Regards, Peter
Linux .config
...
#
# Platform support
#
#CONFIG_PPC_CHRPis not set
#CONFIG_MPC5121_ADSis not set
#CONFIG_MPC5121_GENERICis not set
CONFIG_PPC_MPC52xx=yCONFIG_PPC_MPC5200_SIMPLE=y
#CONFIG_PPC_EFIKAis not setCONFIG_PPC_LITE5200=y
#CONFIG_PPC_MEDIA5200is not setCONFIG_PPC_MPC5200_BUGFIX=y
#CONFIG_PPC_MPC5200_GPIOis not setCONFIG_PPC_MPC5200_LPBFIFO=y
CONFIG_PPC_BESTCOMM=yCONFIG_PPC_BESTCOMM_FEC=yCONFIG_PPC_BESTCOMM_GEN_BD=y
#CONFIG_SIMPLE_GPIOis not set
..
# Bus options
#CONFIG_ZONE_DMA=yCONFIG_NEED_SG_DMA_LENGTH=yCONFIG_GENERIC_ISA_DMA=yCONFIG_PPC_PCI_CHOICE=y
...
#
# Generic Driver Options
#CONFIG_STANDALONE=yCONFIG_PREVENT_FIRMWARE_BUILD=yCONFIG_MTD=yCONFIG_MTD_PARTITIONS=yCONFIG_MTD_CMDLINE_PARTS=yQuoted 9 lines
#
# MII PHY device drivers
#CONFIG_LXT_PHY=y## Does not seem to have any influenceCONFIG_NET_ETHERNET=yCONFIG_MII=yCONFIG_ETHOC=y## Does not seem to have any influence
CONFIG_FEC_MPC52xx=y ## Must be Y in roder to get adapter working with uboot's init
CONFIG_FEC_MPC52xx_MDIO=y ## Must be Y in roder to get adapter working with uboot's init_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://lists.ozlabs.org/listinfo/linuxppc-dev