Pull request: u-boot-imx

Hi Wolfgang,

The following changes since commit cdc51c294ad33879c4e57edf4c9d2155381b1d59:

Merge branch 'next' of ../next (2010-12-22 21:16:17 +0100)

are available in the git repository at:

git://www.denx.de/git/u-boot-imx.git master

Liu Hui-R64343 (9):
MX51EVK: UART does not print out the early information
MX5: Add initial support for MX53 processor
fec_mxc: add support for MX53 processor
serial_mxc: add support for MX53 processor
mxc_gpio: add support for MX53 processor
mxc_i2c: add support for MX53 processor
fsl_pmic: add I2C interface support
imximage: Add MX53 boot image support MX5:MX53: add initial support for MX53EVK board

 MAINTAINERS                                 |    4 +
 arch/arm/cpu/armv7/mx5/iomux.c              |   30 ++-
 arch/arm/cpu/armv7/mx5/lowlevel_init.S      |   91 +++---
 arch/arm/cpu/armv7/mx5/soc.c                |   22 +-
 arch/arm/include/asm/arch-mx5/asm-offsets.h |    5 +
 arch/arm/include/asm/arch-mx5/imx-regs.h    |   82 ++---
 arch/arm/include/asm/arch-mx5/iomux.h       |  102 ------
 arch/arm/include/asm/arch-mx5/mx5x_pins.h   |  469
++++++++++++++++++++++++++-
 board/freescale/mx51evk/mx51evk.c           |   11 +-
 board/freescale/mx53evk/Makefile            |   48 +++
 board/freescale/mx53evk/config.mk           |   24 ++
 board/freescale/mx53evk/imximage.cfg        |  112 +++++++
 board/freescale/mx53evk/mx53evk.c           |  397 +++++++++++++++++++++++
 boards.cfg                                  |    1 +
 doc/README.imximage                         |   12 +-
 drivers/gpio/mxc_gpio.c                     |    9 +-
 drivers/i2c/mxc_i2c.c                       |   21 +-
 drivers/misc/fsl_pmic.c                     |   45 +++-
 drivers/net/fec_mxc.c                       |    2 +-
 drivers/net/fec_mxc.h                       |    4 +-
 drivers/serial/serial_mxc.c                 |    6 +
 include/configs/mx51evk.h                   |    5 +-
 include/configs/mx53evk.h                   |  193 +++++++++++
 include/configs/vision2.h                   |    3 +-
 include/mc13892.h                           |    5 +
 tools/imximage.c                            |  421 +++++++++++++++++++-----
 tools/imximage.h                            |  110 +++++--
 27 files changed, 1900 insertions(+), 334 deletions(-)
 mode change 100644 => 100755 arch/arm/cpu/armv7/mx5/iomux.c
 mode change 100644 => 100755 arch/arm/cpu/armv7/mx5/lowlevel_init.S
 mode change 100644 => 100755 arch/arm/include/asm/arch-mx5/imx-regs.h
 mode change 100644 => 100755 arch/arm/include/asm/arch-mx5/mx5x_pins.h
 create mode 100755 board/freescale/mx53evk/Makefile
 create mode 100755 board/freescale/mx53evk/config.mk
 create mode 100644 board/freescale/mx53evk/imximage.cfg
 create mode 100755 board/freescale/mx53evk/mx53evk.c
 mode change 100644 => 100755 drivers/i2c/mxc_i2c.c
 mode change 100644 => 100755 include/configs/mx51evk.h
 create mode 100755 include/configs/mx53evk.h

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

Le 13/01/2011 07:40, Stefano Babic a ?crit :

I think I should be the one doing the pull as the ARM custodian. I'll be doing it this evening.

Amicalement,

Albert.

Sorry, of course you are right, I forget to readdress my pull-request after you became the ARM custodian ;-).

Stefano

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================

Le 13/01/2011 07:40, Stefano Babic a ?crit :

Applied to u-boot-arm/master, thanks.

Amicalement,

Albert.

Dear Stefano Babic,

Is this really you working base? Then you should probably rebase against current master first.

Please sends your pull request to the Albert, ARM custodian.

Best regards,

Wolfgang Denk

DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
A modem is a baudy house.

Yes, I do it.

Sorry, for the inconvenience. Albert has already saw I sent the pull request to the wrong person and has pulled to u-boot-arm. I will be more careful next time before sending the pull request.

Best regards,
Stefano Babic

=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================