linux gpio
Hello,
I am new to linux (coming from eCos).
My backlight driver does not start up because the reset gpio pin is not correct specified.
How does gpio work in Linux?
I have 2 platforms that use the same backlight driver, under arm, for freescale imx: imx31_3ds and imx27_3ds. I don't think that matters, I just need to understand the linux gpio.
The imx31 platform gives the number 88 as gpio number to the backlight driver.
That number comes out of 'iomux-mx3.h'.
In 'iomux-mx27.h' the GPIO's are specified in an other way, the "hardware" way, specifying bank and port. I think Linux GPIO needs a sort of general gpio number.
But how do I calculate that number out of the datasheet?
In the imx31 datasheet, I cannot find that number 88 (or the other numbers in 'iomux-mx3.h').
Kind regards,
J?rgen
Signature · 6 lines
J?rgen Lambrecht R&D Associate Tel: +32 (0)51 303045 Fax: +32 (0)51 310670 http://www.televic-rail.com Televic Rail NV - Leo Bekaertlaan 1 - 8870 Izegem - Belgium Company number 0825.539.581 - RPR Kortrijk
2011/3/29 J?rgen Lambrecht <[email protected]>:
Quoted 7 lines
Hello,
I am new to linux (coming from eCos).
My backlight driver does not start up because the reset gpio pin is not correct specified.
How does gpio work in Linux?
theres no single way.
the new way is in drivers/gpio/* , implemented in gpiolib.c defined in #include <linux/gpio.h>
there are also char drivers, with which Im more familiar. ./char/nsc_gpio.c./char/pc8736x_gpio.c./char/scx200_gpio.c
Quoted 9 lines
I have 2 platforms that use the same backlight driver, under arm, for freescale imx:
imx31_3dsandimx27_3ds. I don't think that matters, I just need to understand the linux gpio.The imx31 platform gives the number 88 as gpio number to the backlight driver.
That number comes out of 'iomux-mx3.h'.
In 'iomux-mx27.h' the GPIO's are specified in an other way, the "hardware" way, specifying bank and port. I think Linux GPIO needs a sort of general gpio number.
The problem here is that board IDs are somewhat arbitrary, whereas driver IDs are predictable. Take soekris 4801 as an example; it has gpio on the CPU-SOC (scx200_gpio), and on a peripheral chip (pc8736x_gpio)
The board uses CPU pins for Leds (and reset button I think), but the GPIO exposed to connector is on pc87366 chip.
The char drivers use major device numbers to select the chip & driver, and minor numbers to select the bank/pin on the chip.
THis lets users create device files with suitable names / numbers.
Quoted 4 lines
But how do I calculate that number out of the datasheet? In the imx31 datasheet, I cannot find that number 88 (or the other numbers in '
iomux-mx3.h').
what driver supports your boards ?
is it a new gpio driver ?
Quoted 17 lines
Kind regards,
J?rgen--
J?rgen Lambrecht
R&D Associate
Tel: +32 (0)51 303045 ? ?Fax: +32 (0)51 310670
http://www.televic-rail.com
Televic Rail NV - Leo Bekaertlaan 1 - 8870 Izegem - Belgium Company number 0825.539.581 - RPR Kortrijk_______________________________________________
Kernelnewbies mailing list
Kernelnewbies at kernelnewbies.org
http://lists.kernelnewbies.org/mailman/listinfo/kernelnewbies
Quoted 11 lines · Jim Cromie
2011/3/29 J?rgen Lambrecht<[email protected]>:
Quoted 7 lines
Hello,
I am new to linux (coming from eCos).
My backlight driver does not start up because the reset gpio pin is not correct specified.
How does gpio work in Linux?theres no single way.
the new way is indrivers/gpio/*, implemented ingpiolib.cdefined in #include<linux/gpio.h>
thanks, i'll use that to write a gpio driver for our own hw.
Quoted 16 lines
there are also char drivers, with which Im more familiar.
./char/nsc_gpio.c./char/pc8736x_gpio.c./char/scx200_gpio.cQuoted 9 lines
I have 2 platforms that use the same backlight driver, under arm, for freescale imx:
imx31_3dsandimx27_3ds. I don't think that matters, I just need to understand the linux gpio.The imx31 platform gives the number 88 as gpio number to the backlight driver.
That number comes out of 'iomux-mx3.h'.
In 'iomux-mx27.h' the GPIO's are specified in an other way, the "hardware" way, specifying bank and port. I think Linux GPIO needs a sort of general gpio number.
Quoted 10 lines
The problem here is that board IDs are somewhat arbitrary, whereas driver IDs are predictable. Take soekris 4801 as an example; it has gpio on the CPU-SOC (
scx200_gpio), and on a peripheral chip (pc8736x_gpio)
The board uses CPU pins for Leds (and reset button I think), but the GPIO exposed to connector is on pc87366 chip.
The char drivers use major device numbers to select the chip& driver, and minor numbers to select the bank/pin on the chip.
THis lets users create device files with suitable names / numbers.
ok, interesting
Quoted 6 lines
Quoted 4 lines
But how do I calculate that number out of the datasheet? In the imx31 datasheet, I cannot find that number 88 (or the other numbers in '
iomux-mx3.h').what driver supports your boards ?
is it a new gpio driver ?
It is ok now: i found it in arch/arm/plat-mxc/include/mach/gpio.h. Thanks, the backlight driver starts up now.
Now I'm looking why udev (or mdev) does not create a /dev/fb0.. reading about it..
Kind regards,
J?rgen
Signature · 6 lines
J?rgen Lambrecht R&D Associate Tel: +32 (0)51 303045 Fax: +32 (0)51 310670 http://www.televic-rail.com Televic Rail NV - Leo Bekaertlaan 1 - 8870 Izegem - Belgium Company number 0825.539.581 - RPR Kortrijk