Zypper question
I'm trying to set up zypper on a qemu based system. I've built
the image & additional packages in 192.168.1.125:/local/qemu_test/tmp/deploy/rpm/ This system is running lighttpd and has the path http://192.168.1.125/qemu-repo
set to that path. I verified it by fetching http://192.168.1.125/qemu-repo/solvedb.conf
which shows up as
/local/qemu_test/tmp/deploy/rpm/qemux86/solvedb /local/qemu_test/tmp/deploy/rpm/i586/solvedb /local/qemu_test/tmp/deploy/rpm/all/solvedb
On the QEMU system, I ran
# zypper addrepo http://192.168.1.125/qemu-repo yocto # zypper refresh No errors were reported
When I tried to install a package, I got this:
# zypper install gst-plugins-base Error building the cache. [1] Repository type can't be determined. warning: Disabling repository 'yocto' because of the above error.
What am I doing wrong?
Note: I tried to follow https://wiki.pokylinux.org/wiki/Zypper_Repository_Setup
Can I help with this (edit the page, etc)? If so, how do I get a login?
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Quoted 20 lines · Gary Thomas
I'm trying to set up zypper on a qemu based system. I've built
the image & additional packages in 192.168.1.125:/local/qemu_test/tmp/deploy/rpm/ This system is running lighttpd and has the path http://192.168.1.125/qemu-repo
set to that path. I verified it by fetching http://192.168.1.125/qemu-repo/solvedb.conf
which shows up as
/local/qemu_test/tmp/deploy/rpm/qemux86/solvedb /local/qemu_test/tmp/deploy/rpm/i586/solvedb /local/qemu_test/tmp/deploy/rpm/all/solvedbOn the QEMU system, I ran
# zypper addrepo http://192.168.1.125/qemu-repo yocto # zypper refresh No errors were reportedWhen I tried to install a package, I got this:
# zypper install gst-plugins-base Error building the cache. [1] Repository type can't be determined. warning: Disabling repository 'yocto' because of the above error.
Quoted 5 lines
What am I doing wrong?
Note: I tried to follow https://wiki.pokylinux.org/wiki/Zypper_Repository_Setup
Can I help with this (edit the page, etc)? If so, how do I get a login?
This is odd. I didn't experience these issues when I was doing the development / testing.
From the above there is an "Error building the cache." the only caching steps that occur during an install is a sync of the system's RPM cache. If something is wrong there you can get a similar error.
Try simply running "rpm -qa" and make sure you get reasonable output. If not, then RPM isn't installed properly. (By default on a minimal system, the RPM database is removed after the rootfs is populated.)
--Mark
Quoted 30 lines · Mark Hatle
Quoted 20 lines · Gary Thomas
I'm trying to set up zypper on a qemu based system. I've built
the image& additional packages in 192.168.1.125:/local/qemu_test/tmp/deploy/rpm/ This system is running lighttpd and has the path http://192.168.1.125/qemu-repo
set to that path. I verified it by fetching http://192.168.1.125/qemu-repo/solvedb.conf
which shows up as
/local/qemu_test/tmp/deploy/rpm/qemux86/solvedb /local/qemu_test/tmp/deploy/rpm/i586/solvedb /local/qemu_test/tmp/deploy/rpm/all/solvedbOn the QEMU system, I ran
# zypper addrepo http://192.168.1.125/qemu-repo yocto # zypper refresh No errors were reportedWhen I tried to install a package, I got this:
# zypper install gst-plugins-base Error building the cache. [1] Repository type can't be determined. warning: Disabling repository 'yocto' because of the above error.Quoted 5 lines
What am I doing wrong?
Note: I tried to follow https://wiki.pokylinux.org/wiki/Zypper_Repository_Setup
Can I help with this (edit the page, etc)? If so, how do I get a login?This is odd. I didn't experience these issues when I was doing the development / testing.
Quoted 7 lines
Quoted 1 line
From the above there is an "Error building the cache." the only caching steps
that occur during an install is a sync of the system's RPM cache. If something is wrong there you can get a similar error.
Try simply running "rpm -qa" and make sure you get reasonable output. If not, then RPM isn't installed properly. (By default on a minimal system, the RPM database is removed after the rootfs is populated.)
'rpm -qa ' worked just fine.
I started with core-image-sato, so it's a pretty complete system to start.
Do I have the repo stuff set up correctly? I can see from the lighttpd logs
that it seems to be looking for files I don't have:
192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/repodata/repomd.xml HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)" 192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/content HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)"
Neither of these files seems to be in tmp/deploy/rpm
Did I miss a step? I ran 'bitbake package-index' just in case.
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Quoted 43 lines · Gary Thomas
Quoted 30 lines · Mark Hatle
Quoted 20 lines · Gary Thomas
I'm trying to set up zypper on a qemu based system. I've built
the image& additional packages in 192.168.1.125:/local/qemu_test/tmp/deploy/rpm/ This system is running lighttpd and has the path http://192.168.1.125/qemu-repo
set to that path. I verified it by fetching http://192.168.1.125/qemu-repo/solvedb.conf
which shows up as
/local/qemu_test/tmp/deploy/rpm/qemux86/solvedb /local/qemu_test/tmp/deploy/rpm/i586/solvedb /local/qemu_test/tmp/deploy/rpm/all/solvedbOn the QEMU system, I ran
# zypper addrepo http://192.168.1.125/qemu-repo yocto # zypper refresh No errors were reportedWhen I tried to install a package, I got this:
# zypper install gst-plugins-base Error building the cache. [1] Repository type can't be determined. warning: Disabling repository 'yocto' because of the above error.Quoted 5 lines
What am I doing wrong?
Note: I tried to follow https://wiki.pokylinux.org/wiki/Zypper_Repository_Setup
Can I help with this (edit the page, etc)? If so, how do I get a login?This is odd. I didn't experience these issues when I was doing the development / testing.
Quoted 7 lines
Quoted 1 line
From the above there is an "Error building the cache." the only caching steps
that occur during an install is a sync of the system's RPM cache. If something is wrong there you can get a similar error.
Try simply running "rpm -qa" and make sure you get reasonable output. If not, then RPM isn't installed properly. (By default on a minimal system, the RPM database is removed after the rootfs is populated.)
'rpm -qa ' worked just fine.
I started with core-image-sato, so it's a pretty complete system to start.
Quoted 9 lines
Do I have the repo stuff set up correctly? I can see from the lighttpd logs that it seems to be looking for files I don't have:
192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/repodata/repomd.xml HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)" 192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/content HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)"Neither of these files seems to be in tmp/deploy/rpm
Did I miss a step? I ran 'bitbake package-index' just in case.
did you run createrepo on the /local/qemu_test/tmp/deploy/rpm directory?
(step 4 in the wiki page) I usually run createrepo <path> -- but apparently it works if you are in the same directory...
--Mark
Quoted 50 lines · Mark Hatle
Quoted 49 lines · Gary Thomas
Quoted 30 lines · Mark Hatle
Quoted 20 lines · Gary Thomas
I'm trying to set up zypper on a qemu based system. I've built
the image& additional packages in 192.168.1.125:/local/qemu_test/tmp/deploy/rpm/
This system is running lighttpd and has the path http://192.168.1.125/qemu-repo
set to that path. I verified it by fetching http://192.168.1.125/qemu-repo/solvedb.conf
which shows up as
/local/qemu_test/tmp/deploy/rpm/qemux86/solvedb /local/qemu_test/tmp/deploy/rpm/i586/solvedb /local/qemu_test/tmp/deploy/rpm/all/solvedbOn the QEMU system, I ran
# zypper addrepo http://192.168.1.125/qemu-repo yocto # zypper refresh No errors were reportedWhen I tried to install a package, I got this:
# zypper install gst-plugins-base Error building the cache. [1] Repository type can't be determined. warning: Disabling repository 'yocto' because of the above error.Quoted 5 lines
What am I doing wrong?
Note: I tried to follow https://wiki.pokylinux.org/wiki/Zypper_Repository_Setup
Can I help with this (edit the page, etc)? If so, how do I get a login?This is odd. I didn't experience these issues when I was doing the development / testing.
Quoted 7 lines
Quoted 1 line
From the above there is an "Error building the cache." the only caching steps
that occur during an install is a sync of the system's RPM cache. If something is wrong there you can get a similar error.
Try simply running "rpm -qa" and make sure you get reasonable output. If not, then RPM isn't installed properly. (By default on a minimal system, the RPM database is removed after the rootfs is populated.)
'rpm -qa ' worked just fine.
I started with core-image-sato, so it's a pretty complete system to start.
Do I have the repo stuff set up correctly? I can see from the lighttpd logs that it seems to be looking for files I don't have:
192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/repodata/repomd.xml HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)" 192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/content HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)"Neither of these files seems to be in tmp/deploy/rpm
Quoted 8 lines
Quoted 3 lines
Did I miss a step? I ran 'bitbake package-index' just in case.
did you run createrepo on the /local/qemu_test/tmp/deploy/rpm directory?
(step 4 in the wiki page) I usually run createrepo<path> -- but apparently it works if you are in the same directory...
Indeed, I missed that step.
Note: I had expected this operation to be handled by 'bitbake package-index' Could it not be done that way so it's always the same, no matter the style of package management?
Thanks
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Quoted 57 lines · Gary Thomas
Quoted 56 lines · Mark Hatle
Quoted 43 lines · Gary Thomas
Quoted 30 lines · Mark Hatle
Quoted 20 lines · Gary Thomas
I'm trying to set up zypper on a qemu based system. I've built
the image& additional packages in 192.168.1.125:/local/qemu_test/tmp/deploy/rpm/
This system is running lighttpd and has the path http://192.168.1.125/qemu-repo
set to that path. I verified it by fetching http://192.168.1.125/qemu-repo/solvedb.conf
which shows up as
/local/qemu_test/tmp/deploy/rpm/qemux86/solvedb /local/qemu_test/tmp/deploy/rpm/i586/solvedb /local/qemu_test/tmp/deploy/rpm/all/solvedbOn the QEMU system, I ran
# zypper addrepo http://192.168.1.125/qemu-repo yocto # zypper refresh No errors were reportedWhen I tried to install a package, I got this:
# zypper install gst-plugins-base Error building the cache. [1] Repository type can't be determined. warning: Disabling repository 'yocto' because of the above error.Quoted 5 lines
What am I doing wrong?
Note: I tried to follow https://wiki.pokylinux.org/wiki/Zypper_Repository_Setup
Can I help with this (edit the page, etc)? If so, how do I get a login?This is odd. I didn't experience these issues when I was doing the development / testing.
Quoted 7 lines
Quoted 1 line
From the above there is an "Error building the cache." the only caching steps
that occur during an install is a sync of the system's RPM cache. If something is wrong there you can get a similar error.
Try simply running "rpm -qa" and make sure you get reasonable output. If not, then RPM isn't installed properly. (By default on a minimal system, the RPM database is removed after the rootfs is populated.)
'rpm -qa ' worked just fine.
I started with core-image-sato, so it's a pretty complete system to start.
Quoted 9 lines
Do I have the repo stuff set up correctly? I can see from the lighttpd logs that it seems to be looking for files I don't have:
192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/repodata/repomd.xml HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)" 192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/content HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)"Neither of these files seems to be in tmp/deploy/rpm
Did I miss a step? I ran 'bitbake package-index' just in case.
did you run createrepo on the /local/qemu_test/tmp/deploy/rpm directory?
Quoted 8 lines
Quoted 2 lines
(step 4 in the wiki page) I usually run createrepo<path> -- but apparently it works if you are in the same directory...
Indeed, I missed that step.
Note: I had expected this operation to be handled by 'bitbake package-index' Could it not be done that way so it's always the same, no matter the style of package management?
It likely can. I didn't even know bitbake package-index was a target. Please file a bug and I'll investigate and get it resolved.
--Mark
Quoted 2 lines
Thanks
Quoted 61 lines · Mark Hatle
Quoted 60 lines · Gary Thomas
Quoted 58 lines · Mark Hatle
Quoted 43 lines · Gary Thomas
Quoted 30 lines · Mark Hatle
Quoted 20 lines · Gary Thomas
I'm trying to set up zypper on a qemu based system. I've built
the image& additional packages in 192.168.1.125:/local/qemu_test/tmp/deploy/rpm/
This system is running lighttpd and has the path http://192.168.1.125/qemu-repo
set to that path. I verified it by fetching http://192.168.1.125/qemu-repo/solvedb.conf
which shows up as
/local/qemu_test/tmp/deploy/rpm/qemux86/solvedb /local/qemu_test/tmp/deploy/rpm/i586/solvedb /local/qemu_test/tmp/deploy/rpm/all/solvedbOn the QEMU system, I ran
# zypper addrepo http://192.168.1.125/qemu-repo yocto # zypper refresh No errors were reportedWhen I tried to install a package, I got this:
# zypper install gst-plugins-base Error building the cache. [1] Repository type can't be determined. warning: Disabling repository 'yocto' because of the above error.Quoted 5 lines
What am I doing wrong?
Note: I tried to follow https://wiki.pokylinux.org/wiki/Zypper_Repository_Setup
Can I help with this (edit the page, etc)? If so, how do I get a login?This is odd. I didn't experience these issues when I was doing the development / testing.
Quoted 7 lines
Quoted 1 line
From the above there is an "Error building the cache." the only caching steps
that occur during an install is a sync of the system's RPM cache. If something is wrong there you can get a similar error.
Try simply running "rpm -qa" and make sure you get reasonable output. If not, then RPM isn't installed properly. (By default on a minimal system, the RPM database is removed after the rootfs is populated.)
'rpm -qa ' worked just fine.
I started with core-image-sato, so it's a pretty complete system to start.
Quoted 9 lines
Do I have the repo stuff set up correctly? I can see from the lighttpd logs that it seems to be looking for files I don't have:
192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/repodata/repomd.xml HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)" 192.168.7.2 192.168.1.125 - [03/May/2011:16:57:38 -0600] "HEAD /qemu-repo/content HTTP/1.1" 404 0 "-" "ZYpp 8.11.0 (curl 7.21.2)"Neither of these files seems to be in tmp/deploy/rpm
Did I miss a step? I ran 'bitbake package-index' just in case.
did you run createrepo on the /local/qemu_test/tmp/deploy/rpm directory?
(step 4 in the wiki page) I usually run createrepo<path> -- but apparently it
works if you are in the same directory...
Quoted 8 lines
Quoted 5 lines
Indeed, I missed that step.
Note: I had expected this operation to be handled by 'bitbake package-index' Could it not be done that way so it's always the same, no matter the style of package management?
It likely can. I didn't even know bitbake package-index was a target. Please file a bug and I'll investigate and get it resolved.
Done, bug #1024
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------