impact of 2X_PROGRAM on read operations
Hello,
I have been trying to understand what does the 2X_PROGRAM configuration (and the IS_2PLANE macro).
At first, I was confused to see that, in onenand_command(), when the command is "READ", the IS_2PLANE macro modifies the block and page address. I was expecting this option only to affect program operations. Then, after seeing jffs2 not finding its magic bitmask after switching the 2X_PROGRAM configuration off, I understood that, since the 2X Program only programs one OOB for two blocks, the read operations had to be impacted anyway.
So, is the following right/almost/wrong ?
Let the size of physical pages/block sizes be 2KiB/128KiB
A filesystem on top of a 2X_PROGRAM-enabled mtd layer sees 4KiB-big pages. When this FS wants to read one 4KiB page, the mtd layer will read 2KiB pages, two times. The layout of the blocks and pages is:
Even plane Odd plane
+--------------------+--------------------+ | page 0 | page 1 (oob 0&1)| <--- one logical page | page 2 | page 3 (oob 2&3)| as seen by a filesystem | page 4 | page 5 (oob 4&5)| | . | . | | . | . | | . | . | | (Block 0) | (Block 1) | +--------------------+--------------------+ | page 128 | page 129 (oob) | | . | . | | . | . | | . | . | | (Block 2) | (Block 3) | +--------------------+--------------------+
(the page number is not the one that would be computed within onenand_command but indicates the order in which pages get read or programmed.)
Is there a way to safely read without 2X_PROGRAM enabled once it has been flashed with a 2X_PROGRAM-enabled flasher (e.g. patched u-boot).
Regards,
David Wagner.
Signature · 4 lines
David Wagner, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com
Quoted 2 lines · David Wagner
Is there a way to safely read without 2X_PROGRAM enabled once it has been flashed with a 2X_PROGRAM-enabled flasher (e.g. patched u-boot).
Not sure about u-boot, but AFAIK 2x is a completely separate mode which gives you I/O speed-up but makes things incompatible with "normal" mode. E.g., you can mount JFFS2 only in one of the modes.
Signature · 2 lines
Best Regards, Artem Bityutskiy (Артём Битюцкий)
Quoted 8 lines · Artem Bityutskiy
Quoted 2 lines · David Wagner
Is there a way to safely read without 2X_PROGRAM enabled once it has been flashed with a 2X_PROGRAM-enabled flasher (e.g. patched u-boot).
Not sure about u-boot, but AFAIK 2x is a completely separate mode which gives you I/O speed-up but makes things incompatible with "normal" mode. E.g., you can mount JFFS2 only in one of the modes.
Ok, so I guess it doesn't make sense trying to address the issue of incompatibilities.
I may have to check once again, but I'm pretty sure, however, that I managed to flash a UBI image with a 2X_PROGRAM-enabled u-boot and read it with a regular kernel. The u-boot code for 2X_PROGRAM handling seems to basically be a copy-paste from the kernel.
If the diagram in my first mail is correct, that could not be possible.
Kyungmin, do you know what's wrong in my reasoning ?
Regards,
David Wagner.
Signature · 4 lines
David Wagner, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com
Quoted 13 lines · David Wagner
Quoted 8 lines · Artem Bityutskiy
Quoted 2 lines · David Wagner
Is there a way to safely read without 2X_PROGRAM enabled once it has been flashed with a 2X_PROGRAM-enabled flasher (e.g. patched u-boot).
Not sure about u-boot, but AFAIK 2x is a completely separate mode which gives you I/O speed-up but makes things incompatible with "normal" mode. E.g., you can mount JFFS2 only in one of the modes.
Ok, so I guess it doesn't make sense trying to address the issue of incompatibilities.
Quoted 7 lines
I may have to check once again, but I'm pretty sure, however, that I managed to flash a UBI image with a 2X_PROGRAM-enabled u-boot and read it with a regular kernel. The u-boot code for 2X_PROGRAM handling seems to basically be a copy-paste from the kernel.
If the diagram in my first mail is correct, that could not be possible.Kyungmin, do you know what's wrong in my reasoning ?
Since we don't know how program hen 2x_program mode. even though logically BufferRAM0 data will be located block even, BufferRAM1 will be copied to block odd. but it's not clear.
Can you tried to program the sample 4KiB data when 2X_PROGRAM and read (block even, page n) and read (block odd, page n) and compare it? then you can find a difference.
I'm not tried to compare the compatible issue between normal and 2x mode.
Thank you,
Kyungmin Park
Quoted 10 lines
Regards,
David Wagner.
--
David Wagner, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com