Skip to contentSkip to conversation

Linux nodes instead of BPQ32 nodes in the LAN

DISCUSSION Bernard F6BVP 2 participants 3 messages Jul 9, 2011 – Jul 15, 2011

lore
Share & tools
lore
#0 lore raw

Hello Miroslav,

Giving us the listing of your /etc/ax25/axports
and /etc/ax25/ax25d.conf files would be helpful
for it looks like you did not declare any ax25 ports
in those files.
According to http://www.linuxselfhelp.com/HOWTO/AX25-HOWTO/x495.html :
"To configure the BPQ support you need to configure the Ethernet device with an AX.25 callsign. The following command will do this for you:

# /sbin/ifconfig bpq0 hw ax25 vk2ktj-14 up

Again, remember that the callsign you specify should match the entry in the /etc/ax25/axports file that you wish to use for this port."

Look at paragraph 6.2 in previous page link.

Concerning netromd, it also needs valid ax25 ports in /etc/ax25/nrbroadcast

73 de Bernard, f6bvp

-------------

Hi all!

I have been experimenting with 3 computers as AX.25 nodes in a home LAN, as follows:

            _____________      ___________________   __________________
VHF        |MS DOS 5 comp|    |MS Windows XP comp|  |MS Windows XP comp|
TRX--TNC2--|  BPQ 4.09d  | -- |    BPQ32 4.10f   |--|    BPQ32 4.10f   |

ant ------------- ------------------ ------------------

(1) (2) (3)

In the situation above all 3 nodes talk to each other without problems. What I wanted to do was to replace comps (2) and (3) with Linux nodes. Both of those comps are dual-boot: (2) is Debian 6.0.1a, and (3) is Ubuntu 10.04.2 LTS.

Ok so I installed libax, ax25tools and ax25apps, as well as node on both
(2) and (3) by using Synaptic but am not able to activate the nodes properly. In fact, I have edited the main files in /etc/ax25 on both machines according to the ancient AX.25-howto and then tried the following commands in Ubuntu terminal (in Debian root terminal of course without 'sudo'):

sudo modprobe bpqether (did not complain anything)
sudo /sbin/ifconfig bpq0 hw ax25 yt7mpb-15 up (did not complain either) sudo ifconfig responded with:
bpq0 Link encap:AMPR AX.25 HWaddr YT7MPB-15
UP RUNNING MTU:256 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

eth0 Link encap:Ethernet HWaddr 00:25:22:3d:9f:22
inet addr:192.168.0.4 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::225:22ff:fe3d:9f22/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:116 errors:0 dropped:0 overruns:0 frame:0 TX packets:125 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000
RX bytes:12824 (12.8 KB) TX bytes:11360 (11.3 KB) Interrupt:27

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:15 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
RX bytes:957 (957.0 B) TX bytes:957 (957.0 B)

sudo modprobe netrom (did not complain)
sudo nrattach netrom responded with:
NET/ROM port netrom bound to device nr0
sudo nrattach netnod responded with:
NET/ROM port netnod bound to device nr1
sudo ax25d responded with:
axconfig: port bpq0 not active
ax25d: no AX.25 port data configured
sudo netromd
axconfig: port bpq0 not active
netromd: no AX.25 ports defined

I suppose that I mis-configured and/or forgotten some important steps and would like to contact somebody with more experience with Linux nodes running over Ethernet. Btw, at the moment I do not plan to run any RF ports on those Linux machines - just to have netrom nodes on them so that those nodes should be able to talk with the dos computer (1), and probably later I will add LinFBB to replace the WinFBB's that run over BPQ32 nodes when (2) and (3) are booted as Win XP.

Regards,

Misko YT7MPB

#1 lore raw
Quoted 4 lines · On 07/09/2011 11:27 PM, Bernard F6BVP wrote:

Giving us the listing of your /etc/ax25/axports and /etc/ax25/ax25d.conf files would be helpful for it looks like you did not declare any ax25 ports in those files.

Hi Bernard! Here it is:

# /etc/ax25/axports
#
# The format of this file is:
#
# name callsign speed paclen window description
#
#1	OH2BNS-1	1200	255	2	144.675 MHz (1200  bps)
#2	OH2BNS-9	38400	255	7	TNOS/Linux  (38400 bps)
bpq0	YT7MPB-15    10000000	255	7	New LAN  (100 Mbps)
# /etc/ax25/ax25d.conf
#
# ax25d Configuration File.
#
# AX.25 Ports begin with a '['.
#
#[OH2BNS VIA 1]
#NOCALL   * * * * * *  L
#default  * * * * * *  -	root  /usr/local/sbin/ttylinkd	ttylinkd
#
[YT7MPB-5 VIA bpq0]
NOCALL   * * * * * *  L
default  * * * * * *  -		root  /usr/sbin/node	node
#
#
#[OH2BNS VIA 2]
#NOCALL   * * * * * *  L
#default  * * * * * *  -	root  /usr/local/sbin/ttylinkd	ttylinkd
#
#[OH2BNS-2 VIA 2]
#NOCALL   * * * * * *  L
#default  * * * * * *  -	root  /usr/sbin/node	node
#
#[OH2BNS-3 VIA 2]
#NOCALL   * * * * * *  L
#default  * * * * * *  -	root  /usr/local/sbin/axwrapper	axwrapper
/#usr/bin/finger finger
#
#[OH2BNS-9]
#NOCALL  * * * * * *  L
#default * * * * * *  -	root  /usr/sbin/node	node
#
# NET/ROM Ports begin with a '<'.
#
#<netrom>
#NOCALL  * * * * * *  L
#default * * * * * *  -	root  /usr/local/sbin/ttylinkd	ttylinkd
#
<netrom>
NOCALL   * * * * * *  L
default  * * * * * *  -	root  /usr/sbin/node	node
#
#<netnod>
NOCALL  * * * * * *  L
default * * * * * *  -	root  /usr/sbin/node	node
#
Quoted 9 lines

According to http://www.linuxselfhelp.com/HOWTO/AX25-HOWTO/x495.html :
"To configure the BPQ support you need to configure the Ethernet device with an AX.25 callsign. The following command will do this for you:

# /sbin/ifconfig bpq0 hw ax25 vk2ktj-14 up

Again, remember that the callsign you specify should match the entry in the /etc/ax25/axports file that you wish to use for this port."

As I mentioned in my previous post, I used the command:

sudo /sbin/ifconfig bpq0 hw ax25 yt7mpb-15 up

and i did not get any error related to it.

Quoted 2 lines

Look at paragraph 6.2 in previous page link.

Ok, will check the link...

Quoted 2 lines

Concerning netromd, it also needs valid ax25 ports in /etc/ax25/nrbroadcast

Here it is:

# /etc/ax25/nrbroadcast
#
# The format of this file is:
#
# ax25_name min_obs def_qual worst_qual verbose
#
#1	5	192	100	0
#2	5	255	100	1
bpq0	5	255	100	1
Quoted 23 lines

73 de Bernard, f6bvp

-------------

Hi all!

I have been experimenting with 3 computers as AX.25 nodes in a home LAN, as follows:

            _____________      ___________________   __________________
VHF        |MS DOS 5 comp|    |MS Windows XP comp|  |MS Windows XP comp|
TRX--TNC2--|  BPQ 4.09d  | -- |    BPQ32 4.10f   |--|    BPQ32 4.10f   |

ant ------------- ------------------ ------------------

(1) (2) (3)

In the situation above all 3 nodes talk to each other without problems. What I wanted to do was to replace comps (2) and (3) with Linux nodes. Both of those comps are dual-boot: (2) is Debian 6.0.1a, and (3) is Ubuntu 10.04.2 LTS.

#2 lore raw

Hello Miroslav,

As an old time user of ROSE/FPAC node under Linux I ignore most if not all of bpq application.

I browsed for it and found two other things that may help you ?

http://www.linuxdoc.org/HOWTO/AX25-HOWTO/x1958.html

and look at bpqparms manual for it suggests other things.

# man bpqparms

I have a question : did you load ax25 module ?

And finally are you sure bpq is still supported with kernel 2.6 ?

73 de Bernard, f6bvp

Selon Miroslav Skoric <[email protected]>:
http://www.linuxdoc.org/HOWTO/AX25-HOWTO/x1958.html

Quoted 126 lines · On 07/09/2011 11:27 PM, Bernard F6BVP wrote:
Quoted 5 lines

Giving us the listing of your /etc/ax25/axports and /etc/ax25/ax25d.conf files would be helpful for it looks like you did not declare any ax25 ports in those files.

Hi Bernard! Here it is:

# /etc/ax25/axports
#
# The format of this file is:
#
# name callsign speed paclen window description
#
#1	OH2BNS-1	1200	255	2	144.675 MHz (1200  bps)
#2	OH2BNS-9	38400	255	7	TNOS/Linux  (38400 bps)
bpq0	YT7MPB-15    10000000	255	7	New LAN  (100 Mbps)
# /etc/ax25/ax25d.conf
#
# ax25d Configuration File.
#
# AX.25 Ports begin with a '['.
#
#[OH2BNS VIA 1]
#NOCALL   * * * * * *  L
#default  * * * * * *  -	root  /usr/local/sbin/ttylinkd	ttylinkd
#
[YT7MPB-5 VIA bpq0]
NOCALL   * * * * * *  L
default  * * * * * *  -		root  /usr/sbin/node	node
#
#
#[OH2BNS VIA 2]
#NOCALL   * * * * * *  L
#default  * * * * * *  -	root  /usr/local/sbin/ttylinkd	ttylinkd
#
#[OH2BNS-2 VIA 2]
#NOCALL   * * * * * *  L
#default  * * * * * *  -	root  /usr/sbin/node	node
#
#[OH2BNS-3 VIA 2]
#NOCALL   * * * * * *  L
#default  * * * * * *  -	root  /usr/local/sbin/axwrapper	axwrapper
/#usr/bin/finger finger
#
#[OH2BNS-9]
#NOCALL  * * * * * *  L
#default * * * * * *  -	root  /usr/sbin/node	node
#
# NET/ROM Ports begin with a '<'.
#
#<netrom>
#NOCALL  * * * * * *  L
#default * * * * * *  -	root  /usr/local/sbin/ttylinkd	ttylinkd
#
<netrom>
NOCALL   * * * * * *  L
default  * * * * * *  -	root  /usr/sbin/node	node
#
#<netnod>
NOCALL  * * * * * *  L
default * * * * * *  -	root  /usr/sbin/node	node
#
Quoted 9 lines

According to http://www.linuxselfhelp.com/HOWTO/AX25-HOWTO/x495.html :
"To configure the BPQ support you need to configure the Ethernet device with an AX.25 callsign. The following command will do this for you:

# /sbin/ifconfig bpq0 hw ax25 vk2ktj-14 up

Again, remember that the callsign you specify should match the entry in the /etc/ax25/axports file that you wish to use for this port."

As I mentioned in my previous post, I used the command:

sudo /sbin/ifconfig bpq0 hw ax25 yt7mpb-15 up

and i did not get any error related to it.

Quoted 2 lines

Look at paragraph 6.2 in previous page link.

Ok, will check the link...

Quoted 2 lines

Concerning netromd, it also needs valid ax25 ports in /etc/ax25/nrbroadcast

Here it is:

# /etc/ax25/nrbroadcast
#
# The format of this file is:
#
# ax25_name min_obs def_qual worst_qual verbose
#
#1	5	192	100	0
#2	5	255	100	1
bpq0	5	255	100	1
Quoted 23 lines

73 de Bernard, f6bvp

-------------

Hi all!

I have been experimenting with 3 computers as AX.25 nodes in a home LAN, as follows:

            _____________      ___________________   __________________
VHF        |MS DOS 5 comp|    |MS Windows XP comp|  |MS Windows XP comp|
TRX--TNC2--|  BPQ 4.09d  | -- |    BPQ32 4.10f   |--|    BPQ32 4.10f   |

ant ------------- ------------------ ------------------

(1) (2) (3)

In the situation above all 3 nodes talk to each other without problems. What I wanted to do was to replace comps (2) and (3) with Linux nodes. Both of those comps are dual-boot: (2) is Debian 6.0.1a, and (3) is Ubuntu 10.04.2 LTS.

Signature · 1 line
73 de Bernard, F6BVP