Skip to contentSkip to conversation

understanding GPIO registers

DISCUSSION OrazioPirataDelloSpazio (Lorenzo) 2 participants 4 messages Aug 25, 2011 – Aug 28, 2011

lore
Share & tools
lore
#0 lore raw

Hi there,
I have a motherbord (VIA EPIA LT) with a digital I/O port composed by 4 GPI and 4 GPO (chip: SMSC SCH3114).

I want to provide voltage to GPO and read the input value of GPI with a software.

Using the generic gpio kernel module, I tried to export pins without success :

echo N > /sys/class/gpio/export
write error : invalid argument

I tried for several values of N (from 1 to 1000 !) then I gave up thinking I would have needed some information from the hardware producer. Now I have got this information that is the following offsets and addresses.

How can I use these registers to fix the export problem or alternatively how to write a simple userspace C program to read and write these GPIO?

I read gpio.txt but I'm still confused on how to pass from GPIO numbers to registers.

Thanks

Lorenzo

#define sGPIOBaseAddr 0A00
#define GPI1_CTRL_REG 0x6E
#define GPI2_CTRL_REG 0x6F
#define GPI3_CTRL_REG 0x72
#define GPI4_CTRL_REG 0x73
#define GPO1_CTRL_REG 0x2C
#define GPO2_CTRL_REG 0x2D
#define GPO3_CTRL_REG 0x35
#define GPO4_CTRL_REG 0x36

#1 lore raw

hi:

2011/8/26 OrazioPirataDelloSpazio (Lorenzo) <[email protected]>:

Quoted 29 lines

Hi there,
I have a motherbord (VIA EPIA LT) with a digital I/O port composed by 4 GPI and 4 GPO (chip: SMSC SCH3114).

I want to provide voltage to GPO and read the input value of GPI with a software.

Using the generic gpio kernel module, I tried to export pins without success :

echo N > /sys/class/gpio/export
write error : invalid argument

I tried for several values of N (from 1 to 1000 !) then I gave up thinking I would have needed some information from the hardware producer. Now I have got this information that is the following offsets and addresses.

How can I use these registers to fix the export problem or alternatively how to write a simple userspace C program to read and write these GPIO?

I read gpio.txt but I'm still confused on how to pass from GPIO numbers to registers.

Thanks

Lorenzo

Quoted 10 lines

#define sGPIOBaseAddr ? 0A00
#define GPI1_CTRL_REG ? 0x6E
#define GPI2_CTRL_REG ? 0x6F
#define GPI3_CTRL_REG ? 0x72
#define GPI4_CTRL_REG ? 0x73
#define GPO1_CTRL_REG ? 0x2C
#define GPO2_CTRL_REG ? 0x2D
#define GPO3_CTRL_REG ? 0x35
#define GPO4_CTRL_REG ? 0x36

does the base address of gpio in kernel you use is the same or you have modified for your board?
BR

#2 lore raw
Quoted 2 lines · vichy

does the base address of gpio in kernel you use is the same or you have modified for your board?

I didn't modify the kernel.
VIA EPIA LT BIOS set SCH3114 PME BASE ADDRESS at 0A00H

How do you suggest to proceed?

Thanks,

Lorenzo

#3 lore raw

hi:

2011/8/28 OrazioPirataDelloSpazio (Lorenzo) <[email protected]>:

Quoted 9 lines · vichy
Quoted 2 lines

does the base address of gpio in kernel you use is the same or you have modified for your board?

I didn't modify the kernel.
VIA EPIA LT BIOS set SCH3114 PME BASE ADDRESS at 0A00H

How do you suggest to proceed?

Thanks,

How about adding debug messages in the driver?
If that is a PCI device, you may use mmap to map the memory for programming.

BR,