Skip to contentSkip to conversation

nommu warning message

DISCUSSION Larry Finger 2 participants 3 messages Nov 11, 2011 – Nov 15, 2011

lore
Share & tools
lore
#0 lore raw

For the driver rtl8192cu (a USB wireless device), the current version loads the 15KB firmware asynchronously one 32-bit quantity at a time. Although inefficient. this method works with USB 1.1 and USB 2.0 adapters; however, it fails on at least one USB 3.0 adapter with "xhci_hcd 0000:05:00.0: ERROR no room on ep ring" errors.

These errors are believed to arise from small, fixed-size ep rings. There is a vendor driver that works with that same hardware. The major difference is that it uses synchronous block writes of 254 bytes. When I tried this with the in-kernel driver, each block write yields a warning as shown below:

nommu_map_single: overflow 41000340d020+254 of device mask ffffffff

The only remaining difference between the two drivers is that the vendor version uses firmware hard coded into the driver while the kernel version uses a file from /lib/firmware.

My cpu info is:

----- /proc/cpuinfo -----

  processor     : 0
  vendor_id     : AuthenticAMD
  cpu family    : 15
  model         : 104
  model name    : AMD Turion(tm) 64 X2 TL-60
  stepping      : 2
  cpu MHz               : 2000.000
  cache size    : 512 KB
  physical id   : 0
  siblings      : 2
  core id               : 0
  cpu cores     : 2
  apicid                : 0
  initial apicid        : 0
  fpu           : yes
  fpu_exception : yes
  cpuid level   : 1
  wp            : yes
  flags         : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov 
pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt rdtscp lm 3dnowext 3dnow rep_good nopl extd_apicid pni cx16 lahf_lm cmp_legacy svm extapic cr8_legacy 3dnowprefetch lbrv
  bogomips      : 4001.06
  TLB size      : 1024 4K pages
  clflush size  : 64

cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual power management: ts fid vid ttp tm stc 100mhzsteps

Could someone please explain the meaning of the above messages? Even with them present, the device works.

Thanks,

Larry

#1 lore raw
Quoted 6 lines · Larry Finger

For the driver rtl8192cu (a USB wireless device), the current version loads the 15KB firmware asynchronously one 32-bit quantity at a time. Although inefficient. this method works with USB 1.1 and USB 2.0 adapters; however, it fails on at least one USB 3.0 adapter with "xhci_hcd 0000:05:00.0: ERROR no room on ep ring" errors.

Quoted 7 lines

These errors are believed to arise from small, fixed-size ep rings. There is a vendor driver that works with that same hardware. The major difference is that it uses synchronous block writes of 254 bytes. When I tried this with the in-kernel driver, each block write yields a warning as shown below:

nommu_map_single: overflow 41000340d020+254 of device mask ffffffff

Strange. This means that your system uses the nommu DMA driver. But for your hardware the GART or SWIOTLB should be used.

Even more strange is the address used for the device. I don't believe is is correct, otherwise your Laptop would have a very huge amount of RAM :)

The I think there are two issues here: Why is your system using nommu and not GART? Can you check that GART and SWIOTLB are enabled in your kernel config? Second, why is your system using the wrong address? This looks like some kind of driver bug to mee.

Joerg

Signature · 5 lines
AMD Operating System Research Center

Advanced Micro Devices GmbH Einsteinring 24 85609 Dornach
General Managers: Alberto Bozzo, Andrew Bowd
Registration: Dornach, Landkr. Muenchen; Registerger. Muenchen, HRB Nr. 43632
#2 lore raw
Quoted 18 lines · Joerg Roedel
Quoted 6 lines · Larry Finger

For the driver rtl8192cu (a USB wireless device), the current version loads the 15KB firmware asynchronously one 32-bit quantity at a time. Although inefficient. this method works with USB 1.1 and USB 2.0 adapters; however, it fails on at least one USB 3.0 adapter with "xhci_hcd 0000:05:00.0: ERROR no room on ep ring" errors.

Quoted 7 lines

These errors are believed to arise from small, fixed-size ep rings. There is a vendor driver that works with that same hardware. The major difference is that it uses synchronous block writes of 254 bytes. When I tried this with the in-kernel driver, each block write yields a warning as shown below:

nommu_map_single: overflow 41000340d020+254 of device mask ffffffff

Strange. This means that your system uses the nommu DMA driver. But for your hardware the GART or SWIOTLB should be used.

Quoted 8 lines

Even more strange is the address used for the device. I don't believe is is correct, otherwise your Laptop would have a very huge amount of RAM :)

The I think there are two issues here: Why is your system using nommu and not GART? Can you check that GART and SWIOTLB are enabled in your kernel config? Second, why is your system using the wrong address? This looks like some kind of driver bug to mee.

My system has 3 GB of RAM installed, and it has both GART and SWIOTLB enabled.

Your comment about the strange address made me wonder if my driver was somehow overrunning a buffer. Keeping the buffer size constant while reducing the maximum block size by 10 bytes cleared the problem. Obviously, I there is some buffer overhead that I had not considered.

Thanks for pointing me in the right direction.

Larry