3.2rc1: bootup fails: DRHD: handling fault status reg 2
Hi,
when trying to boot kernel 3.2rc1 on my thinkpad t510 I get an endless loop of errors:
DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [0d:00.0] fault addr fffff000
DMAR: [fault reason 02] Present bit in context entry is clear
screenshot can be found here:
http://arndnet.de/lkml/screenshot3.2rc1.jpg
kernel 3.1.1 is booting up flawlessly.
Any idea?
Best regards
Arnd
Hi,
Am 14.11.2011 23:33, schrieb Arnd Hannemann:
Quoted 10 lines
when trying to boot kernel 3.2rc1 on my thinkpad t510 I get an endless loop of errors:
DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [0d:00.0] fault addrfffff000
DMAR: [fault reason 02] Present bit in context entry is clearscreenshot can be found here:
http://arndnet.de/lkml/screenshot3.2rc1.jpgkernel 3.1.1 is booting up flawlessly.
I must have inadvertently enabled CONFIG_INTEL_IOMMU_DEFAULT_ON in my config for 3.2-rc1.
With disabled CONFIG_INTEL_IOMMU_DEFAULT_ON my thinkpad boots up again. Not sure if this is expected?
Best regards
Arnd
Quoted 13 lines · Arnd Hannemann
Hi,
Am 14.11.2011 23:33, schrieb Arnd Hannemann:
Quoted 9 lines
when trying to boot kernel 3.2rc1 on my thinkpad t510 I get an endless loop of errors:
DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [0d:00.0] fault addrfffff000
DMAR: [fault reason 02] Present bit in context entry is clearscreenshot can be found here:
http://arndnet.de/lkml/screenshot3.2rc1.jpg
Quoted 7 lines
Quoted 1 line
kernel 3.1.1 is booting up flawlessly.
I must have inadvertently enabled
CONFIG_INTEL_IOMMU_DEFAULT_ONin my config for 3.2-rc1.With disabled
CONFIG_INTEL_IOMMU_DEFAULT_ONmy thinkpad boots up again. Not sure if this is expected?
No, that's not supposed to happen. Can you post the output of "lspci -vv"? Apparently that device 0d:00.0 is generating unexpected DMA accesses for some reason.
Am 15.11.2011 05:31, schrieb Robert Hancock:
Quoted 16 lines · Arnd Hannemann
Quoted 15 lines
Hi,
Am 14.11.2011 23:33, schrieb Arnd Hannemann:
Quoted 10 lines
when trying to boot kernel 3.2rc1 on my thinkpad t510 I get an endless loop of errors:
DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [0d:00.0] fault addrfffff000
DMAR: [fault reason 02] Present bit in context entry is clearscreenshot can be found here:
http://arndnet.de/lkml/screenshot3.2rc1.jpgkernel 3.1.1 is booting up flawlessly.
Quoted 7 lines
Quoted 5 lines
I must have inadvertently enabled
CONFIG_INTEL_IOMMU_DEFAULT_ONin my config for 3.2-rc1.With disabled
CONFIG_INTEL_IOMMU_DEFAULT_ONmy thinkpad boots up again. Not sure if this is expected?No, that's not supposed to happen. Can you post the output of "lspci -vv"? Apparently that device 0d:00.0 is generating unexpected DMA accesses for some reason.
Looks lite a "Ricoh Co Ltd MMC/SD Host Controller" is the culprit:
0d:00.0 SD Host controller: Ricoh Co Ltd MMC/SD Host Controller (rev 01)
Subsystem: Lenovo Device 2133
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f2500000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [800 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
Best regards,
Arnd
Quoted 10 lines · * Arnd Hannemann ([email protected]) wrote:
Am 14.11.2011 23:33, schrieb Arnd Hannemann:
Quoted 9 lines
when trying to boot kernel 3.2rc1 on my thinkpad t510 I get an endless loop of errors:
DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [0d:00.0] fault addrfffff000
DMAR: [fault reason 02] Present bit in context entry is clearscreenshot can be found here:
http://arndnet.de/lkml/screenshot3.2rc1.jpg
Quoted 7 lines
Quoted 1 line
kernel 3.1.1 is booting up flawlessly.
I must have inadvertently enabled
CONFIG_INTEL_IOMMU_DEFAULT_ONin my config for 3.2-rc1.With disabled
CONFIG_INTEL_IOMMU_DEFAULT_ONmy thinkpad boots up again. Not sure if this is expected?
With CONFIG_INTEL_IOMMU_DEFAULT_ON=n, you have to manually enabled the IOMMU on the kernel commandline. So, yes, disabling that and having your laptop boot is not surprising. The Kconfig item changed names, and the default is yes, so you may have had CONFIG_DMAR_DEFAULT_ON=n, but this would not have propagated forward.
As for the endless loop of DMAR faults...sounds like the Ricoh cardbus/firewire issue where the firewire fucntion does DMA from function 0. I thought this was quirked and fixed though.
thanks,
-chris
Am 15.11.2011 05:36, schrieb Chris Wright:
Quoted 25 lines · * Arnd Hannemann ([email protected]) wrote:
Quoted 10 lines
Am 14.11.2011 23:33, schrieb Arnd Hannemann:
Quoted 9 lines
when trying to boot kernel 3.2rc1 on my thinkpad t510 I get an endless loop of errors:
DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [0d:00.0] fault addrfffff000
DMAR: [fault reason 02] Present bit in context entry is clearscreenshot can be found here:
http://arndnet.de/lkml/screenshot3.2rc1.jpgQuoted 7 lines
Quoted 1 line
kernel 3.1.1 is booting up flawlessly.
I must have inadvertently enabled
CONFIG_INTEL_IOMMU_DEFAULT_ONin my config for 3.2-rc1.With disabled
CONFIG_INTEL_IOMMU_DEFAULT_ONmy thinkpad boots up again. Not sure if this is expected?With
CONFIG_INTEL_IOMMU_DEFAULT_ON=n, you have to manually enabled the IOMMU on the kernel commandline. So, yes, disabling that and having your laptop boot is not surprising. TheKconfigitem changed names, and the default is yes, so you may have hadCONFIG_DMAR_DEFAULT_ON=n, but this would not have propagated forward.
Quoted 3 lines
As for the endless loop of DMAR faults...sounds like the Ricoh cardbus/firewire issue where the firewire fucntion does DMA from function 0. I thought this was quirked and fixed though.
In this case it seems to be
0d:00.0 SD Host controller: Ricoh Co Ltd MMC/SD Host Controller (rev 01)
(using sdhci-pci)
The Fireware function seems to be at a different address:
0d:00.3 FireWire (IEEE 1394): Ricoh Co Ltd FireWire Host Controller (rev 01) (prog-if 10 [OHCI])
Maybe another quirk is needed? Where does this need to be fixed? I suppose sdhci-pci.ko is loaded much later on bootup.
Best regards
Arnd
Quoted 3 lines · Chris Wright
As for the endless loop of DMAR faults...sounds like the Ricoh cardbus/firewire issue where the firewire fucntion does DMA from function 0. I thought this was quirked and fixed though.
Alex? You were handling this as part of the IOMMU 'group' functionality, weren't you? Did you have a test machine... you do now :)
Signature · 1 line
dwmw2
Quoted 7 lines · David Woodhouse
Quoted 3 lines · Chris Wright
As for the endless loop of DMAR faults...sounds like the Ricoh cardbus/firewire issue where the firewire fucntion does DMA from function 0. I thought this was quirked and fixed though.
Alex? You were handling this as part of the IOMMU 'group' functionality, weren't you? Did you have a test machine... you do now :)
The group functionality is primarily for iommu_ops so we can expose to users which devices need to be grouped because of iommu restrictions. We can add a quirk to the grouping for this device, but then we have to figure out how dma_ops makes use of that info too. Maybe we could have a 'struct pci_dev *pci_get_iommu_alias_quirk(struct pci_dev *pdev)' function that given device 0d:00.3 would return 0d:00.0 for this case and both get_domain_for_dev() and intel_iommu_device_group() could make use of it. Thanks,
Alex