Hauppauge HVR-900 HD
Hi All,
I have a Hauppauge HVR-900 HD with ID 2040:b138. Is this device supported, and if so, which driver and firmware do I need?
Regards,
/Fredrik
Quoted 4 lines · Fredrik Lingvall
Hi All,
I have a Hauppauge HVR-900 HD with ID 2040:b138. Is this device supported, and if so, which driver and firmware do I need?
Hi Frank,
It's not currently supported under Linux as it uses a demodulator that there is currently no driver for. As far as I know, nobody's working on it.
Regards,
Devin
Signature · 2 lines
Devin J. Heitmueller - Kernel Labs http://www.kernellabs.com
Quoted 8 lines · Devin Heitmueller
Quoted 4 lines · Fredrik Lingvall
Hi All,
I have a Hauppauge HVR-900 HD with ID 2040:b138. Is this device supported, and if so, which driver and firmware do I need?
Hi Frank,
Quoted 8 lines
It's not currently supported under Linux as it uses a demodulator that there is currently no driver for. As far as I know, nobody's working on it.
Regards,
Devin
Thanks for the info Devin. I had some hope since I found this page:
http://forum.ubuntu-it.org/index.php/topic,423395.5/wap2.html
The dmesg output at least shows much more than I have been able to get (I use 3.2.0-rc3 from the linuxtv git rep). They seem to be able to at least load firmware into the device. It's in Italian so I don't understand much of what they are discussing though.
/Fredrik
Quoted 28 lines · Fredrik Lingvall
Quoted 5 lines · Devin Heitmueller
Quoted 3 lines · Fredrik Lingvall
Hi All,
I have a Hauppauge HVR-900 HD with ID 2040:b138. Is this device
supported,
Quoted 4 lines
Quoted 1 line
and if so, which driver and firmware do I need?
Hi Frank,
It's not currently supported under Linux as it uses a demodulator
that
Quoted 7 lines
there is currently no driver for. As far as I know, nobody's working on it.
Regards,
Devin
Thanks for the info Devin. I had some hope since I found this page:
http://forum.ubuntu-it.org/index.php/topic,423395.5/wap2.html
The dmesg output at least shows much more than I have been able to get (I use 3.2.0-rc3 from the linuxtv git rep). They seem to be able to at least load firmware into the device. It's in Italian so I don't understand much of what they are discussing though.
Quoted 6 lines
/Fredrik
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
On that page they seem to have the unit recognized and a configuration for the analog side of the unit. They also mention a Silabs SI2165 DVB-T/-C demodulator which is obviously not supported.
Regards,
Andy
Quoted 36 lines · Andy Walls
Quoted 28 lines · Fredrik Lingvall
Quoted 5 lines · Devin Heitmueller
Quoted 3 lines · Fredrik Lingvall
Hi All,
I have a Hauppauge HVR-900 HD with ID 2040:b138. Is this device
supported,
Quoted 4 lines
Quoted 1 line
and if so, which driver and firmware do I need?
Hi Frank,
It's not currently supported under Linux as it uses a demodulator
that
Quoted 7 lines
there is currently no driver for. As far as I know, nobody's working on it.
Regards,
Devin
Thanks for the info Devin. I had some hope since I found this page:
http://forum.ubuntu-it.org/index.php/topic,423395.5/wap2.html
The dmesg output at least shows much more than I have been able to get (I use 3.2.0-rc3 from the linuxtv git rep). They seem to be able to at least load firmware into the device. It's in Italian so I don't understand much of what they are discussing though.
Quoted 6 lines
/Fredrik
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 4 lines
On that page they seem to have the unit recognized and a configuration for the analog side of the unit. They also mention a Silabs SI2165 DVB-T/-C demodulator which is obviously not supported.
Regards,
Andy
They had a link to the code on the page:
http://misterox.altervista.org/cx231xx_drivers/newversion_cx231xx.tar.gz
I did a (quick) comparison with that code and the code that's in 3.2.0-rc3. From what I could see it was not a quick fix to port it to 3.2.0-rc3. I will look at it a bit more to see if I can get analog to work too (with 3.2.0-rc3).
/Fredrik