Strange behaviour on audio chipset VIA VT2021 codec
Hello,
i need to develop for my work an audio recorder application. I have to develop the software on Linux OS (Ubuntu 8.04 with kernel 2.6.23.13), and the motherboard is Gigabyte GA-G41MT-S2P (rev. 1.3) where is installed the integrated audio chipset VIA VT2021 codec.
I upgraded the alsa driver to 1.0.25 version for support of audio chipset VIA VT2021. I downloaded the driver and compiled it with the following option
./configure --with-cards=hda-intel --with-sequencer=yes
and i done some experiments with the following simple application example with alsa lib:
#include <alsa/asoundlib.h>
int main()
{
int rc;
int size;
snd_pcm_t *handle;
snd_pcm_hw_params_t *params;
unsigned int val;
int dir;
snd_pcm_uframes_t frames;
char *buffer;
/* Open PCM device for playback. */
rc = snd_pcm_open(&handle, "default",
SND_PCM_STREAM_CAPTURE, 0);
if (rc < 0)
{
fprintf(stderr,
"unable to open pcm device: %s\n",
snd_strerror(rc));
exit(1);
}
/* Allocate a hardware parameters object. */
snd_pcm_hw_params_alloca(¶ms);
/* Fill it in with default values. */
snd_pcm_hw_params_any(handle, params);
/* Set the desired hardware parameters. */
/* Interleaved mode */
snd_pcm_hw_params_set_access(handle, params,
SND_PCM_ACCESS_RW_INTERLEAVED);
/* Signed 16-bit little-endian format */
snd_pcm_hw_params_set_format(handle, params,
SND_PCM_FORMAT_S16_LE);
/* Two channels (stereo) */
snd_pcm_hw_params_set_channels(handle, params, 2);
/* 44100 bits/second sampling rate (CD quality) */
val = 44100;
snd_pcm_hw_params_set_rate_near(handle, params,&val, &dir);
/* Set period size to 32 frames. */
frames = 32;
snd_pcm_hw_params_set_period_size_near(handle,
params, &frames, &dir);
/* Write the parameters to the driver */
rc = snd_pcm_hw_params(handle, params);
if (rc < 0)
{
fprintf(stderr,
"unable to set hw parameters: %s\n",
snd_strerror(rc));
exit(1);
}
/* Use a buffer large enough to hold one period */
snd_pcm_hw_params_get_period_size(params, &frames,&dir);
size = frames * 4; /* 2 bytes/sample, 2 channels */ buffer = (char *) malloc(size);
snd_pcm_hw_params_get_period_time(params,
&val, &dir);
while (1)
{
printf ("Capture data\n");
rc = snd_pcm_readi(handle, buffer, size);
if (rc == -EAGAIN)
{
fprintf(stderr, "EAGAIN occurred\n");
snd_pcm_prepare(handle);
}
else if (rc == -EPIPE)
{
fprintf(stderr, "EPIPE occurred\n");
snd_pcm_prepare(handle);
}
else if (rc == -ESTRPIPE)
{
fprintf(stderr, "ESTRPIPE occurred\n");
snd_pcm_prepare(handle);
}
else if (rc > 0)
{
fprintf(stderr, "read %d ok\n", rc);
}
else
{
fprintf(stderr, "error occurred %s\n", snd_strerror(rc));
exit (1);
}
}
snd_pcm_drain(handle);
snd_pcm_close(handle);
free(buffer);
return 0;
}Running the example above, I found the following behaviors:
1) Until there is no mic plugged, the application stop on snd_pcm_readi. When mic is plugged, the application starts again.
So when i unplug mic the application stops on snd_pcm_readi, when i plug mic the application starts again, and so on.
I want to point out that i achieve the same result with a simple stand alone jack.
2) If i reboot my machine with mic plugged, after restart, I run the application but it stop immediately on snd_pcm_readi
and I need to unplug/plug the mic to stats again the application.
This behavior seems to me quite strange. Please someone could help me to figure out why this behavior ? Maybe something wrong with my example ? Maybe something wrong with compiling options of the driver or maybe into the drivers itself ?
I tried the same application on a different mainboard with Realtek ALC889 codec, and the applications never stops on snd_pcm_readi (I suppose this is the correct behavior), and run correctly.
Let me know if you need more information about.
Thank to all in advance.
Marco