nomatch in bitmap:* sets
Currently only hash:* sets have the "nomatch" feature. Could this be extended to bitmap:* sets as well?
Quoted 2 lines · Mr Dash Four
Currently only hash:* sets have the "nomatch" feature. Could this be extended to bitmap:* sets as well?
Actually, hash:*net* types have the "nomatch" feature. How would it make sense to add it to the bitmap:* types too?
Best regards,
Jozsef
-
E-mail : [email protected], [email protected] PGP key : http://www.kfki.hu/~kadlec/pgp_public_key.txt
Address : Wigner Research Centre for Physics, Hungarian Academy of Sciences
H-1525 Budapest 114, POB. 49, Hungary
Quoted 6 lines
Quoted 3 lines
Currently only hash:* sets have the "nomatch" feature. Could this be extended to bitmap:* sets as well?
Actually, hash:*net* types have the "nomatch" feature. How would it make sense to add it to the bitmap:* types too?
I was thinking along the lines of this:
1. bitmap:port - currently, if I want to exclude specific ports from a given range (say ports 21,80,119,443 from ports range 1-1023) then I have to do the following:
n test-ports bitmap:port range 1-1023 timeout 0
a test-ports 1-20
a test-ports 22-79
a test-ports 81-118
a test-ports 120-442
a test-ports 444-1023
Very inconvenient and it is not immediately obvious which ports have been excluded from that range. By doing something like this:
n test-ports bitmap:port range 1-1023 timeout 0
a test-ports 1-1023
a test-ports 21 nomatch
a test-ports 80 nomatch
a test-ports 119 nomatch
a test-ports 443 nomatch
it is much more clearer what is going on.
2. bitmap:ip - same as above really: If I want to exclude a particular IP addresses from a given range (say 10.1.1.3, 10.1.1.9 and 10.1.1.14 from 10.1.1.0/24) I have to do almost the same as with bitmap:port set above:
n test-bitmap-net bitmap:ip range 10.1.1.0/24 timeout 0
a test-bitmap-net 10.1.1.0-10.1.1.2
a test-bitmap-net 10.1.1.4-10.1.1.8
a test-bitmap-net 10.1.1.10-10.1.1.13
a test-bitmap-net 10.1.1.15-10.1.1.255
Again, it is not immediately obvious what has been excluded. By doing something like the following:
n test-bitmap-net bitmap:ip range 10.1.1.0/24 timeout 0
a test-bitmap-net 10.1.1.0/24
a test-bitmap-net 10.1.1.3 nomatch
a test-bitmap-net 10.1.1.9 nomatch
a test-bitmap-net 10.1.1.14 nomatch
that it is much more clearer.
Quoted 28 lines · Mr Dash Four
Quoted 7 lines
Quoted 3 lines
Currently only hash:* sets have the "nomatch" feature. Could this be extended to bitmap:* sets as well?
Actually, hash:*net* types have the "nomatch" feature. How would it make sense to add it to the bitmap:* types too?
I was thinking along the lines of this:
1. bitmap:port - currently, if I want to exclude specific ports from a given range (say ports 21,80,119,443 from ports range 1-1023) then I have to do the following:
n test-ports bitmap:port range 1-1023 timeout 0
a test-ports 1-20
a test-ports 22-79
a test-ports 81-118
a test-ports 120-442
a test-ports 444-1023Very inconvenient and it is not immediately obvious which ports have been excluded from that range. By doing something like this:
n test-ports bitmap:port range 1-1023 timeout 0
a test-ports 1-1023
a test-ports 21 nomatch
a test-ports 80 nomatch
a test-ports 119 nomatch
a test-ports 443 nomatch
Quoted 1 line
it is much more clearer what is going on.
That's equivalent with
n test-ports bitmap:port range 1-1023 timeout 0
a test-ports 1-1023
d test-ports 21
d test-ports 80
d test-ports 119
d test-ports 443
Therefore I don't see the point of the "nomatch" flag for the bitmap:* types.
Best regards,
Jozsef
-
E-mail : [email protected], [email protected] PGP key : http://www.kfki.hu/~kadlec/pgp_public_key.txt
Address : Wigner Research Centre for Physics, Hungarian Academy of Sciences
H-1525 Budapest 114, POB. 49, Hungary
Quoted 10 lines
That's equivalent with
n test-ports bitmap:port range 1-1023 timeout 0
a test-ports 1-1023
d test-ports 21
d test-ports 80
d test-ports 119
d test-ports 443
It is indeed! That's something I did not know about! The "delete" command wasn't acceptable in ipset restore file before (in all honesty I did try this back in 4.x and gave up after it was rejected). Which version of ipset was this introduced into?
Quoted 9 lines · Mr Dash Four
Quoted 9 lines
That's equivalent with
n test-ports bitmap:port range 1-1023 timeout 0
a test-ports 1-1023
d test-ports 21
d test-ports 80
d test-ports 119
d test-ports 443
Quoted 4 lines
It is indeed! That's something I did not know about! The "delete" command wasn't acceptable in ipset restore file before (in all honesty I did try this back in 4.x and gave up after it was rejected). Which version of ipset was this introduced into?
That was introduced in 6.x (actually, in 5.x).
Every command is accepted in a restore file, except the information ones (help, list).
Best regards,
Jozsef
-
E-mail : [email protected], [email protected] PGP key : http://www.kfki.hu/~kadlec/pgp_public_key.txt
Address : Wigner Research Centre for Physics, Hungarian Academy of Sciences
H-1525 Budapest 114, POB. 49, Hungary
Quoted 5 lines
That was introduced in 6.x (actually, in 5.x).
Every command is accepted in a restore file, except the information ones (help, list).
Thanks Jozsef, I am able to use delete, which suits me fine and does what I want it to.