Skip to contentSkip to conversation

net: sh_eth: modify the definitions of regsiter

PATCH New Shimoda 3 participants 3 messages Jun 27, 2012 – Jul 24, 2012 Network drivers

lore
Share & tools
lore

Shimoda

#0 lore raw

PATCH 3/4 net: sh_eth: modify the definitions of regsiter

The previous code had many similar definitions in each CPU.

This patch borrows from the sh_eth driver of Linux kernel.

---
 drivers/net/sh_eth.c |  108 ++++++++---------
 drivers/net/sh_eth.h |  331 +++++++++++++++++++++++++++++++-------------------
 2 files changed, 258 insertions(+), 181 deletions(-)
drivers/net/sh_eth.c +52 -56
index 262762d..7b429e8 100644
@@ -76,8 +76,8 @@ int sh_eth_send(struct eth_device *dev, void *packet, int len)
 		port_info->tx_desc_cur->td0 = TD_TACT | TD_TFP;
 
 	/* Restart the transmitter if disabled */
-	if (!(inl(EDTRR(port)) & EDTRR_TRNS))
-		outl(EDTRR_TRNS, EDTRR(port));
+	if (!(sh_eth_read(eth, EDTRR) & EDTRR_TRNS))
+		sh_eth_write(eth, EDTRR_TRNS, EDTRR);
 
 	/* Wait until packet is transmitted */
 	timeout = TIMEOUT_CNT;
@@ -129,25 +129,24 @@ int sh_eth_recv(struct eth_device *dev)
 	}
 
 	/* Restart the receiver if disabled */
-	if (!(inl(EDRRR(port)) & EDRRR_R))
-		outl(EDRRR_R, EDRRR(port));
+	if (!(sh_eth_read(eth, EDRRR) & EDRRR_R))
+		sh_eth_write(eth, EDRRR_R, EDRRR);
 
 	return len;
 }
 
 static int sh_eth_reset(struct sh_eth_dev *eth)
 {
-	int port = eth->port;
 #if defined(SH_ETH_TYPE_GETHER)
 	int ret = 0, i;
 
 	/* Start e-dmac transmitter and receiver */
-	outl(EDSR_ENALL, EDSR(port));
+	sh_eth_write(eth, EDSR_ENALL, EDSR);
 
 	/* Perform a software reset and wait for it to complete */
-	outl(EDMR_SRST, EDMR(port));
+	sh_eth_write(eth, EDMR_SRST, EDMR);
 	for (i = 0; i < TIMEOUT_CNT ; i++) {
-		if (!(inl(EDMR(port)) & EDMR_SRST))
+		if (!(sh_eth_read(eth, EDMR) & EDMR_SRST))
 			break;
 		udelay(1000);
 	}
@@ -159,9 +158,9 @@ static int sh_eth_reset(struct sh_eth_dev *eth)
 
 	return ret;
 #else
-	outl(inl(EDMR(port)) | EDMR_SRST, EDMR(port));
+	sh_eth_write(eth, sh_eth_read(eth, EDMR) | EDMR_SRST, EDMR);
 	udelay(3000);
-	outl(inl(EDMR(port)) & ~EDMR_SRST, EDMR(port));
+	sh_eth_write(eth, sh_eth_read(eth, EDMR) & ~EDMR_SRST, EDMR);
 
 	return 0;
 #endif
@@ -207,11 +206,11 @@ static int sh_eth_tx_desc_init(struct sh_eth_dev *eth)
 
 	/* Point the controller to the tx descriptor list. Must use physical
 	   addresses */
-	outl(ADDR_TO_PHY(port_info->tx_desc_base), TDLAR(port));
+	sh_eth_write(eth, ADDR_TO_PHY(port_info->tx_desc_base), TDLAR);
 #if defined(SH_ETH_TYPE_GETHER)
-	outl(ADDR_TO_PHY(port_info->tx_desc_base), TDFAR(port));
-	outl(ADDR_TO_PHY(cur_tx_desc), TDFXR(port));
-	outl(0x01, TDFFR(port));/* Last discriptor bit */
+	sh_eth_write(eth, ADDR_TO_PHY(port_info->tx_desc_base), TDFAR);
+	sh_eth_write(eth, ADDR_TO_PHY(cur_tx_desc), TDFXR);
+	sh_eth_write(eth, 0x01, TDFFR);/* Last discriptor bit */
 #endif
 
 err:
@@ -275,11 +274,11 @@ static int sh_eth_rx_desc_init(struct sh_eth_dev *eth)
 	cur_rx_desc->rd0 |= RD_RDLE;
 
 	/* Point the controller to the rx descriptor list */
-	outl(ADDR_TO_PHY(port_info->rx_desc_base), RDLAR(port));
+	sh_eth_write(eth, ADDR_TO_PHY(port_info->rx_desc_base), RDLAR);
 #if defined(SH_ETH_TYPE_GETHER)
-	outl(ADDR_TO_PHY(port_info->rx_desc_base), RDFAR(port));
-	outl(ADDR_TO_PHY(cur_rx_desc), RDFXR(port));
-	outl(RDFFR_RDLF, RDFFR(port));
+	sh_eth_write(eth, ADDR_TO_PHY(port_info->rx_desc_base), RDFAR);
+	sh_eth_write(eth, ADDR_TO_PHY(cur_rx_desc), RDFXR);
+	sh_eth_write(eth, RDFFR_RDLF, RDFFR);
 #endif
 
 	return ret;
@@ -364,38 +363,39 @@ static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd)
 	struct phy_device *phy;
 
 	/* Configure e-dmac registers */
-	outl((inl(EDMR(port)) & ~EMDR_DESC_R) | EDMR_EL, EDMR(port));
-	outl(0, EESIPR(port));
-	outl(0, TRSCER(port));
-	outl(0, TFTR(port));
-	outl((FIFO_SIZE_T | FIFO_SIZE_R), FDR(port));
-	outl(RMCR_RST, RMCR(port));
+	sh_eth_write(eth, (sh_eth_read(eth, EDMR) & ~EMDR_DESC_R) | EDMR_EL,
+		     EDMR);
+	sh_eth_write(eth, 0, EESIPR);
+	sh_eth_write(eth, 0, TRSCER);
+	sh_eth_write(eth, 0, TFTR);
+	sh_eth_write(eth, (FIFO_SIZE_T | FIFO_SIZE_R), FDR);
+	sh_eth_write(eth, RMCR_RST, RMCR);
 #if defined(SH_ETH_TYPE_GETHER)
-	outl(0, RPADIR(port));
+	sh_eth_write(eth, 0, RPADIR);
 #endif
-	outl((FIFO_F_D_RFF | FIFO_F_D_RFD), FCFTR(port));
+	sh_eth_write(eth, (FIFO_F_D_RFF | FIFO_F_D_RFD), FCFTR);
 
 	/* Configure e-mac registers */
-	outl(0, ECSIPR(port));
+	sh_eth_write(eth, 0, ECSIPR);
 
 	/* Set Mac address */
 	val = dev->enetaddr[0] << 24 | dev->enetaddr[1] << 16 |
 	    dev->enetaddr[2] << 8 | dev->enetaddr[3];
-	outl(val, MAHR(port));
+	sh_eth_write(eth, val, MAHR);
 
 	val = dev->enetaddr[4] << 8 | dev->enetaddr[5];
-	outl(val, MALR(port));
+	sh_eth_write(eth, val, MALR);
 
-	outl(RFLR_RFL_MIN, RFLR(port));
+	sh_eth_write(eth, RFLR_RFL_MIN, RFLR);
 #if defined(SH_ETH_TYPE_GETHER)
-	outl(0, PIPR(port));
-	outl(APR_AP, APR(port));
-	outl(MPR_MP, MPR(port));
-	outl(TPAUSER_TPAUSE, TPAUSER(port));
+	sh_eth_write(eth, 0, PIPR);
+	sh_eth_write(eth, APR_AP, APR);
+	sh_eth_write(eth, MPR_MP, MPR);
+	sh_eth_write(eth, TPAUSER_TPAUSE, TPAUSER);
 #endif
 
 #if defined(CONFIG_CPU_SH7734)
-	outl(CONFIG_SH_ETHER_SH7734_MII, RMII_MII(port));
+	sh_eth_write(eth, CONFIG_SH_ETHER_SH7734_MII, RMII_MII);
 #endif
 	/* Configure phy */
 	ret = sh_eth_phy_config(eth);
@@ -412,34 +412,35 @@ static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd)
 	if (phy->speed == 100) {
 		printf(SHETHER_NAME ": 100Base/");
 #if defined(SH_ETH_TYPE_GETHER)
-		outl(GECMR_100B, GECMR(port));
+		sh_eth_write(eth, GECMR_100B, GECMR);
 #elif defined(CONFIG_CPU_SH7757)
-		outl(1, RTRATE(port));
+		sh_eth_write(eth, 1, RTRATE);
 #elif defined(CONFIG_CPU_SH7724)
 		val = ECMR_RTM;
 #endif
 	} else if (phy->speed == 10) {
 		printf(SHETHER_NAME ": 10Base/");
 #if defined(SH_ETH_TYPE_GETHER)
-		outl(GECMR_10B, GECMR(port));
+		sh_eth_write(eth, GECMR_10B, GECMR);
 #elif defined(CONFIG_CPU_SH7757)
-		outl(0, RTRATE(port));
+		sh_eth_write(eth, 0, RTRATE);
 #endif
 	}
 #if defined(SH_ETH_TYPE_GETHER)
 	else if (phy->speed == 1000) {
 		printf(SHETHER_NAME ": 1000Base/");
-		outl(GECMR_1000B, GECMR(port));
+		sh_eth_write(eth, GECMR_1000B, GECMR);
 	}
 #endif
 
 	/* Check if full duplex mode is supported by the phy */
 	if (phy->duplex) {
 		printf("Full\n");
-		outl(val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE|ECMR_DM), ECMR(port));
+		sh_eth_write(eth, val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE|ECMR_DM),
+			     ECMR);
 	} else {
 		printf("Half\n");
-		outl(val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE),  ECMR(port));
+		sh_eth_write(eth, val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE), ECMR);
 	}
 
 	return ret;
@@ -454,12 +455,12 @@ static void sh_eth_start(struct sh_eth_dev *eth)
 	 * Enable the e-dmac receiver only. The transmitter will be enabled when
 	 * we have something to transmit
 	 */
-	outl(EDRRR_R, EDRRR(eth->port));
+	sh_eth_write(eth, EDRRR_R, EDRRR);
 }
 
 static void sh_eth_stop(struct sh_eth_dev *eth)
 {
-	outl(~EDRRR_R, EDRRR(eth->port));
+	sh_eth_write(eth, ~EDRRR_R, EDRRR);
 }
 
 int sh_eth_init(struct eth_device *dev, bd_t *bd)
@@ -563,9 +564,8 @@ static int sh_eth_bb_init(struct bb_miiphy_bus *bus)
 static int sh_eth_bb_mdio_active(struct bb_miiphy_bus *bus)
 {
 	struct sh_eth_dev *eth = bus->priv;
-	int port = eth->port;
 
-	outl(inl(PIR(port)) | PIR_MMD, PIR(port));
+	sh_eth_write(eth, sh_eth_read(eth, PIR) | PIR_MMD, PIR);
 
 	return 0;
 }
@@ -573,9 +573,8 @@ static int sh_eth_bb_mdio_active(struct bb_miiphy_bus *bus)
 static int sh_eth_bb_mdio_tristate(struct bb_miiphy_bus *bus)
 {
 	struct sh_eth_dev *eth = bus->priv;
-	int port = eth->port;
 
-	outl(inl(PIR(port)) & ~PIR_MMD, PIR(port));
+	sh_eth_write(eth, sh_eth_read(eth, PIR) & ~PIR_MMD, PIR);
 
 	return 0;
 }
@@ -583,12 +582,11 @@ static int sh_eth_bb_mdio_tristate(struct bb_miiphy_bus *bus)
 static int sh_eth_bb_set_mdio(struct bb_miiphy_bus *bus, int v)
 {
 	struct sh_eth_dev *eth = bus->priv;
-	int port = eth->port;
 
 	if (v)
-		outl(inl(PIR(port)) | PIR_MDO, PIR(port));
+		sh_eth_write(eth, sh_eth_read(eth, PIR) | PIR_MDO, PIR);
 	else
-		outl(inl(PIR(port)) & ~PIR_MDO, PIR(port));
+		sh_eth_write(eth, sh_eth_read(eth, PIR) & ~PIR_MDO, PIR);
 
 	return 0;
 }
@@ -596,9 +594,8 @@ static int sh_eth_bb_set_mdio(struct bb_miiphy_bus *bus, int v)
 static int sh_eth_bb_get_mdio(struct bb_miiphy_bus *bus, int *v)
 {
 	struct sh_eth_dev *eth = bus->priv;
-	int port = eth->port;
 
-	*v = (inl(PIR(port)) & PIR_MDI) >> 3;
+	*v = (sh_eth_read(eth, PIR) & PIR_MDI) >> 3;
 
 	return 0;
 }
@@ -606,12 +603,11 @@ static int sh_eth_bb_get_mdio(struct bb_miiphy_bus *bus, int *v)
 static int sh_eth_bb_set_mdc(struct bb_miiphy_bus *bus, int v)
 {
 	struct sh_eth_dev *eth = bus->priv;
-	int port = eth->port;
 
 	if (v)
-		outl(inl(PIR(port)) | PIR_MDC, PIR(port));
+		sh_eth_write(eth, sh_eth_read(eth, PIR) | PIR_MDC, PIR);
 	else
-		outl(inl(PIR(port)) & ~PIR_MDC, PIR(port));
+		sh_eth_write(eth, sh_eth_read(eth, PIR) & ~PIR_MDC, PIR);
 
 	return 0;
 }
drivers/net/sh_eth.h +206 -125

349 lines not on this page · raw message

Signature · 1 line
1.7.1
#1 lore raw

PATCH 3/4 net: sh_eth: modify the definitions of regsiter

2012/6/27 Shimoda, Yoshihiro <[email protected]>:

Quoted 635 lines

The previous code had many similar definitions in each CPU.

This patch borrows from the sh_eth driver of Linux kernel.

---
?drivers/net/sh_eth.c | ?108 ++++++++--------- ?drivers/net/sh_eth.h | ?331 +++++++++++++++++++++++++++++++------------------- ?2 files changed, 258 insertions(+), 181 deletions(-)

drivers/net/sh_eth.c +0 -0
index 262762d..7b429e8 100644
@@ -76,8 +76,8 @@ int sh_eth_send(struct eth_device *dev, void *packet, int len)
 ? ? ? ? ? ? ? ?port_info->tx_desc_cur->td0 = TD_TACT | TD_TFP;
 

? ? ? ?/* Restart the transmitter if disabled */
- ? ? ? if (!(inl(EDTRR(port)) & EDTRR_TRNS))
- ? ? ? ? ? ? ? outl(EDTRR_TRNS, EDTRR(port));
+ ? ? ? if (!(sh_eth_read(eth, EDTRR) & EDTRR_TRNS))
+ ? ? ? ? ? ? ? sh_eth_write(eth, EDTRR_TRNS, EDTRR);

? ? ? ?/* Wait until packet is transmitted */
? ? ? ?timeout = TIMEOUT_CNT;

drivers/net/sh_eth.c +0 -0
@@ -129,25 +129,24 @@ int sh_eth_recv(struct eth_device *dev)
 ? ? ? ?}
 

? ? ? ?/* Restart the receiver if disabled */
- ? ? ? if (!(inl(EDRRR(port)) & EDRRR_R))
- ? ? ? ? ? ? ? outl(EDRRR_R, EDRRR(port));
+ ? ? ? if (!(sh_eth_read(eth, EDRRR) & EDRRR_R))
+ ? ? ? ? ? ? ? sh_eth_write(eth, EDRRR_R, EDRRR);

? ? ? ?return len;
?}

?static int sh_eth_reset(struct sh_eth_dev *eth)
?{
- ? ? ? int port = eth->port;
?#if defined(SH_ETH_TYPE_GETHER)
? ? ? ?int ret = 0, i;

? ? ? ?/* Start e-dmac transmitter and receiver */
- ? ? ? outl(EDSR_ENALL, EDSR(port));
+ ? ? ? sh_eth_write(eth, EDSR_ENALL, EDSR);

? ? ? ?/* Perform a software reset and wait for it to complete */
- ? ? ? outl(EDMR_SRST, EDMR(port));
+ ? ? ? sh_eth_write(eth, EDMR_SRST, EDMR);
? ? ? ?for (i = 0; i < TIMEOUT_CNT ; i++) {
- ? ? ? ? ? ? ? if (!(inl(EDMR(port)) & EDMR_SRST))
+ ? ? ? ? ? ? ? if (!(sh_eth_read(eth, EDMR) & EDMR_SRST)) ? ? ? ? ? ? ? ? ? ? ? ?break;
? ? ? ? ? ? ? ?udelay(1000);
? ? ? ?}

drivers/net/sh_eth.c +0 -0
@@ -159,9 +158,9 @@ static int sh_eth_reset(struct sh_eth_dev *eth)
 
 ? ? ? ?return ret;

?#else
- ? ? ? outl(inl(EDMR(port)) | EDMR_SRST, EDMR(port));
+ ? ? ? sh_eth_write(eth, sh_eth_read(eth, EDMR) | EDMR_SRST, EDMR); ? ? ? ?udelay(3000);
- ? ? ? outl(inl(EDMR(port)) & ~EDMR_SRST, EDMR(port));
+ ? ? ? sh_eth_write(eth, sh_eth_read(eth, EDMR) & ~EDMR_SRST, EDMR);

? ? ? ?return 0;
?#endif

drivers/net/sh_eth.c +0 -0
@@ -207,11 +206,11 @@ static int sh_eth_tx_desc_init(struct sh_eth_dev *eth)
 

? ? ? ?/* Point the controller to the tx descriptor list. Must use physical ? ? ? ? ? addresses */
- ? ? ? outl(ADDR_TO_PHY(port_info->tx_desc_base), TDLAR(port));
+ ? ? ? sh_eth_write(eth, ADDR_TO_PHY(port_info->tx_desc_base), TDLAR); ?#if defined(SH_ETH_TYPE_GETHER)
- ? ? ? outl(ADDR_TO_PHY(port_info->tx_desc_base), TDFAR(port));
- ? ? ? outl(ADDR_TO_PHY(cur_tx_desc), TDFXR(port));
- ? ? ? outl(0x01, TDFFR(port));/* Last discriptor bit */
+ ? ? ? sh_eth_write(eth, ADDR_TO_PHY(port_info->tx_desc_base), TDFAR);
+ ? ? ? sh_eth_write(eth, ADDR_TO_PHY(cur_tx_desc), TDFXR);
+ ? ? ? sh_eth_write(eth, 0x01, TDFFR);/* Last discriptor bit */ ?#endif

?err:

drivers/net/sh_eth.c +0 -0
@@ -275,11 +274,11 @@ static int sh_eth_rx_desc_init(struct sh_eth_dev *eth)
 ? ? ? ?cur_rx_desc->rd0 |= RD_RDLE;
 

? ? ? ?/* Point the controller to the rx descriptor list */
- ? ? ? outl(ADDR_TO_PHY(port_info->rx_desc_base), RDLAR(port));
+ ? ? ? sh_eth_write(eth, ADDR_TO_PHY(port_info->rx_desc_base), RDLAR); ?#if defined(SH_ETH_TYPE_GETHER)
- ? ? ? outl(ADDR_TO_PHY(port_info->rx_desc_base), RDFAR(port));
- ? ? ? outl(ADDR_TO_PHY(cur_rx_desc), RDFXR(port));
- ? ? ? outl(RDFFR_RDLF, RDFFR(port));
+ ? ? ? sh_eth_write(eth, ADDR_TO_PHY(port_info->rx_desc_base), RDFAR);
+ ? ? ? sh_eth_write(eth, ADDR_TO_PHY(cur_rx_desc), RDFXR);
+ ? ? ? sh_eth_write(eth, RDFFR_RDLF, RDFFR);
?#endif

? ? ? ?return ret;

drivers/net/sh_eth.c +0 -0
@@ -364,38 +363,39 @@ static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd)
 ? ? ? ?struct phy_device *phy;
 

? ? ? ?/* Configure e-dmac registers */
- ? ? ? outl((inl(EDMR(port)) & ~EMDR_DESC_R) | EDMR_EL, EDMR(port));
- ? ? ? outl(0, EESIPR(port));
- ? ? ? outl(0, TRSCER(port));
- ? ? ? outl(0, TFTR(port));
- ? ? ? outl((FIFO_SIZE_T | FIFO_SIZE_R), FDR(port));
- ? ? ? outl(RMCR_RST, RMCR(port));
+ ? ? ? sh_eth_write(eth, (sh_eth_read(eth, EDMR) & ~EMDR_DESC_R) | EDMR_EL,
+ ? ? ? ? ? ? ? ? ? ?EDMR);
+ ? ? ? sh_eth_write(eth, 0, EESIPR);
+ ? ? ? sh_eth_write(eth, 0, TRSCER);
+ ? ? ? sh_eth_write(eth, 0, TFTR);
+ ? ? ? sh_eth_write(eth, (FIFO_SIZE_T | FIFO_SIZE_R), FDR);
+ ? ? ? sh_eth_write(eth, RMCR_RST, RMCR);
?#if defined(SH_ETH_TYPE_GETHER)
- ? ? ? outl(0, RPADIR(port));
+ ? ? ? sh_eth_write(eth, 0, RPADIR);
?#endif
- ? ? ? outl((FIFO_F_D_RFF | FIFO_F_D_RFD), FCFTR(port));
+ ? ? ? sh_eth_write(eth, (FIFO_F_D_RFF | FIFO_F_D_RFD), FCFTR);

? ? ? ?/* Configure e-mac registers */
- ? ? ? outl(0, ECSIPR(port));
+ ? ? ? sh_eth_write(eth, 0, ECSIPR);

? ? ? ?/* Set Mac address */
? ? ? ?val = dev->enetaddr[0] << 24 | dev->enetaddr[1] << 16 | ? ? ? ? ? ?dev->enetaddr[2] << 8 | dev->enetaddr[3];
- ? ? ? outl(val, MAHR(port));
+ ? ? ? sh_eth_write(eth, val, MAHR);

? ? ? ?val = dev->enetaddr[4] << 8 | dev->enetaddr[5];
- ? ? ? outl(val, MALR(port));
+ ? ? ? sh_eth_write(eth, val, MALR);

- ? ? ? outl(RFLR_RFL_MIN, RFLR(port));
+ ? ? ? sh_eth_write(eth, RFLR_RFL_MIN, RFLR); ?#if defined(SH_ETH_TYPE_GETHER)
- ? ? ? outl(0, PIPR(port));
- ? ? ? outl(APR_AP, APR(port));
- ? ? ? outl(MPR_MP, MPR(port));
- ? ? ? outl(TPAUSER_TPAUSE, TPAUSER(port));
+ ? ? ? sh_eth_write(eth, 0, PIPR);
+ ? ? ? sh_eth_write(eth, APR_AP, APR);
+ ? ? ? sh_eth_write(eth, MPR_MP, MPR);
+ ? ? ? sh_eth_write(eth, TPAUSER_TPAUSE, TPAUSER); ?#endif

?#if defined(CONFIG_CPU_SH7734)
- ? ? ? outl(CONFIG_SH_ETHER_SH7734_MII, RMII_MII(port));
+ ? ? ? sh_eth_write(eth, CONFIG_SH_ETHER_SH7734_MII, RMII_MII); ?#endif
? ? ? ?/* Configure phy */
? ? ? ?ret = sh_eth_phy_config(eth);

drivers/net/sh_eth.c +2 -2
@@ -412,34 +412,35 @@ static int sh_eth_config(struct sh_eth_dev *eth, bd_t *bd)
 ? ? ? ?if (phy->speed == 100) {
 ? ? ? ? ? ? ? ?printf(SHETHER_NAME ": 100Base/");
 ?#if defined(SH_ETH_TYPE_GETHER)
- ? ? ? ? ? ? ? outl(GECMR_100B, GECMR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, GECMR_100B, GECMR);
 ?#elif defined(CONFIG_CPU_SH7757)
- ? ? ? ? ? ? ? outl(1, RTRATE(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, 1, RTRATE);
 ?#elif defined(CONFIG_CPU_SH7724)
 ? ? ? ? ? ? ? ?val = ECMR_RTM;

?#endif
? ? ? ?} else if (phy->speed == 10) {
? ? ? ? ? ? ? ?printf(SHETHER_NAME ": 10Base/"); ?#if defined(SH_ETH_TYPE_GETHER)
- ? ? ? ? ? ? ? outl(GECMR_10B, GECMR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, GECMR_10B, GECMR); ?#elif defined(CONFIG_CPU_SH7757)
- ? ? ? ? ? ? ? outl(0, RTRATE(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, 0, RTRATE); ?#endif
? ? ? ?}
?#if defined(SH_ETH_TYPE_GETHER)
? ? ? ?else if (phy->speed == 1000) {
? ? ? ? ? ? ? ?printf(SHETHER_NAME ": 1000Base/");
- ? ? ? ? ? ? ? outl(GECMR_1000B, GECMR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, GECMR_1000B, GECMR); ? ? ? ?}
?#endif

? ? ? ?/* Check if full duplex mode is supported by the phy */
? ? ? ?if (phy->duplex) {
? ? ? ? ? ? ? ?printf("Full\n");
- ? ? ? ? ? ? ? outl(val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE|ECMR_DM), ECMR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE|ECMR_DM),
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ?ECMR);
? ? ? ?} else {
? ? ? ? ? ? ? ?printf("Half\n");
- ? ? ? ? ? ? ? outl(val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE), ?ECMR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, val | (ECMR_CHG_DM|ECMR_RE|ECMR_TE), ECMR); ? ? ? ?}

? ? ? ?return ret;

drivers/net/sh_eth.c +0 -0
@@ -454,12 +455,12 @@ static void sh_eth_start(struct sh_eth_dev *eth)

? ? ? ? * Enable the e-dmac receiver only. The transmitter will be enabled when ? ? ? ? * we have something to transmit
? ? ? ? */
- ? ? ? outl(EDRRR_R, EDRRR(eth->port));
+ ? ? ? sh_eth_write(eth, EDRRR_R, EDRRR);
?}

?static void sh_eth_stop(struct sh_eth_dev *eth)
?{
- ? ? ? outl(~EDRRR_R, EDRRR(eth->port));
+ ? ? ? sh_eth_write(eth, ~EDRRR_R, EDRRR);
?}

?int sh_eth_init(struct eth_device *dev, bd_t *bd)

drivers/net/sh_eth.c +3 -6
@@ -563,9 +564,8 @@ static int sh_eth_bb_init(struct bb_miiphy_bus *bus)
 ?static int sh_eth_bb_mdio_active(struct bb_miiphy_bus *bus)
 ?{
 ? ? ? ?struct sh_eth_dev *eth = bus->priv;
- ? ? ? int port = eth->port;
 
- ? ? ? outl(inl(PIR(port)) | PIR_MMD, PIR(port));
+ ? ? ? sh_eth_write(eth, sh_eth_read(eth, PIR) | PIR_MMD, PIR);
 
 ? ? ? ?return 0;
 ?}
@@ -573,9 +573,8 @@ static int sh_eth_bb_mdio_active(struct bb_miiphy_bus *bus)
 ?static int sh_eth_bb_mdio_tristate(struct bb_miiphy_bus *bus)
 ?{
 ? ? ? ?struct sh_eth_dev *eth = bus->priv;
- ? ? ? int port = eth->port;
 
- ? ? ? outl(inl(PIR(port)) & ~PIR_MMD, PIR(port));
+ ? ? ? sh_eth_write(eth, sh_eth_read(eth, PIR) & ~PIR_MMD, PIR);
 
 ? ? ? ?return 0;
 ?}
@@ -583,12 +582,11 @@ static int sh_eth_bb_mdio_tristate(struct bb_miiphy_bus *bus)
 ?static int sh_eth_bb_set_mdio(struct bb_miiphy_bus *bus, int v)
 ?{
 ? ? ? ?struct sh_eth_dev *eth = bus->priv;
- ? ? ? int port = eth->port;
 
 ? ? ? ?if (v)
- ? ? ? ? ? ? ? outl(inl(PIR(port)) | PIR_MDO, PIR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, sh_eth_read(eth, PIR) | PIR_MDO, PIR);

? ? ? ?else
- ? ? ? ? ? ? ? outl(inl(PIR(port)) & ~PIR_MDO, PIR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, sh_eth_read(eth, PIR) & ~PIR_MDO, PIR);

? ? ? ?return 0;
?}

drivers/net/sh_eth.c +2 -4
@@ -596,9 +594,8 @@ static int sh_eth_bb_set_mdio(struct bb_miiphy_bus *bus, int v)
 ?static int sh_eth_bb_get_mdio(struct bb_miiphy_bus *bus, int *v)
 ?{
 ? ? ? ?struct sh_eth_dev *eth = bus->priv;
- ? ? ? int port = eth->port;
 
- ? ? ? *v = (inl(PIR(port)) & PIR_MDI) >> 3;
+ ? ? ? *v = (sh_eth_read(eth, PIR) & PIR_MDI) >> 3;
 
 ? ? ? ?return 0;
 ?}
@@ -606,12 +603,11 @@ static int sh_eth_bb_get_mdio(struct bb_miiphy_bus *bus, int *v)
 ?static int sh_eth_bb_set_mdc(struct bb_miiphy_bus *bus, int v)
 ?{
 ? ? ? ?struct sh_eth_dev *eth = bus->priv;
- ? ? ? int port = eth->port;
 
 ? ? ? ?if (v)
- ? ? ? ? ? ? ? outl(inl(PIR(port)) | PIR_MDC, PIR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, sh_eth_read(eth, PIR) | PIR_MDC, PIR);

? ? ? ?else
- ? ? ? ? ? ? ? outl(inl(PIR(port)) & ~PIR_MDC, PIR(port));
+ ? ? ? ? ? ? ? sh_eth_write(eth, sh_eth_read(eth, PIR) & ~PIR_MDC, PIR);

? ? ? ?return 0;
?}

drivers/net/sh_eth.h +180 -0
index 401ef69..13003ec 100644
@@ -97,140 +97,196 @@ struct sh_eth_dev {
 ? ? ? ?struct sh_eth_info port_info[MAX_PORT_NUM];
 ?};
 
+/* from linux/drivers/net/ethernet/renesas/sh_eth.h */
+enum {
+ ? ? ? /* E-DMAC registers */
+ ? ? ? EDSR = 0,
+ ? ? ? EDMR,
+ ? ? ? EDTRR,
+ ? ? ? EDRRR,
+ ? ? ? EESR,
+ ? ? ? EESIPR,
+ ? ? ? TDLAR,
+ ? ? ? TDFAR,
+ ? ? ? TDFXR,
+ ? ? ? TDFFR,
+ ? ? ? RDLAR,
+ ? ? ? RDFAR,
+ ? ? ? RDFXR,
+ ? ? ? RDFFR,
+ ? ? ? TRSCER,
+ ? ? ? RMFCR,
+ ? ? ? TFTR,
+ ? ? ? FDR,
+ ? ? ? RMCR,
+ ? ? ? EDOCR,
+ ? ? ? TFUCR,
+ ? ? ? RFOCR,
+ ? ? ? FCFTR,
+ ? ? ? RPADIR,
+ ? ? ? TRIMD,
+ ? ? ? RBWAR,
+ ? ? ? TBRAR,
+
+ ? ? ? /* Ether registers */
+ ? ? ? ECMR,
+ ? ? ? ECSR,
+ ? ? ? ECSIPR,
+ ? ? ? PIR,
+ ? ? ? PSR,
+ ? ? ? RDMLR,
+ ? ? ? PIPR,
+ ? ? ? RFLR,
+ ? ? ? IPGR,
+ ? ? ? APR,
+ ? ? ? MPR,
+ ? ? ? PFTCR,
+ ? ? ? PFRCR,
+ ? ? ? RFCR,
+ ? ? ? RFCF,
+ ? ? ? TPAUSER,
+ ? ? ? TPAUSECR,
+ ? ? ? BCFR,
+ ? ? ? BCFRR,
+ ? ? ? GECMR,
+ ? ? ? BCULR,
+ ? ? ? MAHR,
+ ? ? ? MALR,
+ ? ? ? TROCR,
+ ? ? ? CDCR,
+ ? ? ? LCCR,
+ ? ? ? CNDCR,
+ ? ? ? CEFCR,
+ ? ? ? FRECR,
+ ? ? ? TSFRCR,
+ ? ? ? TLFRCR,
+ ? ? ? CERCR,
+ ? ? ? CEECR,
+ ? ? ? MAFCR,
+ ? ? ? RTRATE,
+ ? ? ? CSMR,
+ ? ? ? RMII_MII,
+
+ ? ? ? /* This value must be written at last. */
+ ? ? ? SH_ETH_MAX_REGISTER_OFFSET,
+};
+
+static const u16 sh_eth_offset_gigabit[SH_ETH_MAX_REGISTER_OFFSET] = {
+ ? ? ? [EDSR] ?= 0x0000,
+ ? ? ? [EDMR] ?= 0x0400,
+ ? ? ? [EDTRR] = 0x0408,
+ ? ? ? [EDRRR] = 0x0410,
+ ? ? ? [EESR] ?= 0x0428,
+ ? ? ? [EESIPR] ? ? ? ?= 0x0430,
+ ? ? ? [TDLAR] = 0x0010,
+ ? ? ? [TDFAR] = 0x0014,
+ ? ? ? [TDFXR] = 0x0018,
+ ? ? ? [TDFFR] = 0x001c,
+ ? ? ? [RDLAR] = 0x0030,
+ ? ? ? [RDFAR] = 0x0034,
+ ? ? ? [RDFXR] = 0x0038,
+ ? ? ? [RDFFR] = 0x003c,
+ ? ? ? [TRSCER] ? ? ? ?= 0x0438,
+ ? ? ? [RMFCR] = 0x0440,
+ ? ? ? [TFTR] ?= 0x0448,
+ ? ? ? [FDR] ? = 0x0450,
+ ? ? ? [RMCR] ?= 0x0458,
+ ? ? ? [RPADIR] ? ? ? ?= 0x0460,
+ ? ? ? [FCFTR] = 0x0468,
+ ? ? ? [CSMR] = 0x04E4,
+
+ ? ? ? [ECMR] ?= 0x0500,
+ ? ? ? [ECSR] ?= 0x0510,
+ ? ? ? [ECSIPR] ? ? ? ?= 0x0518,
+ ? ? ? [PIR] ? = 0x0520,
+ ? ? ? [PSR] ? = 0x0528,
+ ? ? ? [PIPR] ?= 0x052c,
+ ? ? ? [RFLR] ?= 0x0508,
+ ? ? ? [APR] ? = 0x0554,
+ ? ? ? [MPR] ? = 0x0558,
+ ? ? ? [PFTCR] = 0x055c,
+ ? ? ? [PFRCR] = 0x0560,
+ ? ? ? [TPAUSER] ? ? ? = 0x0564,
+ ? ? ? [GECMR] = 0x05b0,
+ ? ? ? [BCULR] = 0x05b4,
+ ? ? ? [MAHR] ?= 0x05c0,
+ ? ? ? [MALR] ?= 0x05c8,
+ ? ? ? [TROCR] = 0x0700,
+ ? ? ? [CDCR] ?= 0x0708,
+ ? ? ? [LCCR] ?= 0x0710,
+ ? ? ? [CEFCR] = 0x0740,
+ ? ? ? [FRECR] = 0x0748,
+ ? ? ? [TSFRCR] ? ? ? ?= 0x0750,
+ ? ? ? [TLFRCR] ? ? ? ?= 0x0758,
+ ? ? ? [RFCR] ?= 0x0760,
+ ? ? ? [CERCR] = 0x0768,
+ ? ? ? [CEECR] = 0x0770,
+ ? ? ? [MAFCR] = 0x0778,
+ ? ? ? [RMII_MII] = ?0x0790,
+};
+
+static const u16 sh_eth_offset_fast_sh4[SH_ETH_MAX_REGISTER_OFFSET] = {
+ ? ? ? [ECMR] ?= 0x0100,
+ ? ? ? [RFLR] ?= 0x0108,
+ ? ? ? [ECSR] ?= 0x0110,
+ ? ? ? [ECSIPR] ? ? ? ?= 0x0118,
+ ? ? ? [PIR] ? = 0x0120,
+ ? ? ? [PSR] ? = 0x0128,
+ ? ? ? [RDMLR] = 0x0140,
+ ? ? ? [IPGR] ?= 0x0150,
+ ? ? ? [APR] ? = 0x0154,
+ ? ? ? [MPR] ? = 0x0158,
+ ? ? ? [TPAUSER] ? ? ? = 0x0164,
+ ? ? ? [RFCF] ?= 0x0160,
+ ? ? ? [TPAUSECR] ? ? ?= 0x0168,
+ ? ? ? [BCFRR] = 0x016c,
+ ? ? ? [MAHR] ?= 0x01c0,
+ ? ? ? [MALR] ?= 0x01c8,
+ ? ? ? [TROCR] = 0x01d0,
+ ? ? ? [CDCR] ?= 0x01d4,
+ ? ? ? [LCCR] ?= 0x01d8,
+ ? ? ? [CNDCR] = 0x01dc,
+ ? ? ? [CEFCR] = 0x01e4,
+ ? ? ? [FRECR] = 0x01e8,
+ ? ? ? [TSFRCR] ? ? ? ?= 0x01ec,
+ ? ? ? [TLFRCR] ? ? ? ?= 0x01f0,
+ ? ? ? [RFCR] ?= 0x01f4,
+ ? ? ? [MAFCR] = 0x01f8,
+ ? ? ? [RTRATE] ? ? ? ?= 0x01fc,
+
+ ? ? ? [EDMR] ?= 0x0000,
+ ? ? ? [EDTRR] = 0x0008,
+ ? ? ? [EDRRR] = 0x0010,
+ ? ? ? [TDLAR] = 0x0018,
+ ? ? ? [RDLAR] = 0x0020,
+ ? ? ? [EESR] ?= 0x0028,
+ ? ? ? [EESIPR] ? ? ? ?= 0x0030,
+ ? ? ? [TRSCER] ? ? ? ?= 0x0038,
+ ? ? ? [RMFCR] = 0x0040,
+ ? ? ? [TFTR] ?= 0x0048,
+ ? ? ? [FDR] ? = 0x0050,
+ ? ? ? [RMCR] ?= 0x0058,
+ ? ? ? [TFUCR] = 0x0064,
+ ? ? ? [RFOCR] = 0x0068,
+ ? ? ? [FCFTR] = 0x0070,
+ ? ? ? [RPADIR] ? ? ? ?= 0x0078,
+ ? ? ? [TRIMD] = 0x007c,
+ ? ? ? [RBWAR] = 0x00c8,
+ ? ? ? [RDFAR] = 0x00cc,
+ ? ? ? [TBRAR] = 0x00d4,
+ ? ? ? [TDFAR] = 0x00d8,
+};
+

?/* Register Address */

drivers/net/sh_eth.h +1 -1
-#ifdef CONFIG_CPU_SH7763
+#if defined(CONFIG_CPU_SH7763) || defined(CONFIG_CPU_SH7734)

?#define SH_ETH_TYPE_GETHER
?#define BASE_IO_ADDR ? 0xfee00000

drivers/net/sh_eth.h +0 -36
-
-#define EDSR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0000)
-
-#define TDLAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0010)
-#define TDFAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0014)
-#define TDFXR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0018)
-#define TDFFR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x001c)
-
-#define RDLAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0030)
-#define RDFAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0034)
-#define RDFXR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0038)
-#define RDFFR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x003c)
-
-#define EDMR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0400)
-#define EDTRR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0408)
-#define EDRRR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0410)
-#define EESR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0428)
-#define EESIPR(port) ? (BASE_IO_ADDR + 0x800 * (port) + 0x0430)
-#define TRSCER(port) ? (BASE_IO_ADDR + 0x800 * (port) + 0x0438)
-#define TFTR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0448)
-#define FDR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0450)
-#define RMCR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0458)
-#define RPADIR(port) ? (BASE_IO_ADDR + 0x800 * (port) + 0x0460)
-#define FCFTR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0468)
-#define ECMR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0500)
-#define RFLR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0508)
-#define ECSIPR(port) ? (BASE_IO_ADDR + 0x800 * (port) + 0x0518)
-#define PIR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0520)
-#define PIPR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x052c)
-#define APR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0554)
-#define MPR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0558)
-#define TPAUSER(port) ?(BASE_IO_ADDR + 0x800 * (port) + 0x0564)
-#define GECMR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x05b0)
-#define MALR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x05c8)
-#define MAHR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x05c0)
-

?#elif defined(CONFIG_CPU_SH7757)
?#define SH_ETH_TYPE_ETHER
?#define BASE_IO_ADDR ? 0xfef00000

drivers/net/sh_eth.h +0 -25
-
-#define TDLAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0018)
-#define RDLAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0020)
-
-#define EDMR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0000)
-#define EDTRR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0008)
-#define EDRRR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0010)
-#define EESR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0028)
-#define EESIPR(port) ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0030)
-#define TRSCER(port) ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0038)
-#define TFTR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0048)
-#define FDR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0050)
-#define RMCR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0058)
-#define FCFTR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0070)
-#define ECMR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0100)
-#define RFLR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0108)
-#define ECSIPR(port) ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x0118)
-#define PIR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0120)
-#define APR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0154)
-#define MPR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0158)
-#define TPAUSER(port) ? ? ? ? ?(BASE_IO_ADDR + 0x800 * (port) + 0x0164)
-#define MAHR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x01c0)
-#define MALR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x01c8)
-#define RTRATE(port) ? ? ? ? ? (BASE_IO_ADDR + 0x800 * (port) + 0x01fc)
-

?#elif defined(CONFIG_CPU_SH7724)
?#define SH_ETH_TYPE_ETHER
?#define BASE_IO_ADDR ? 0xA4600000

drivers/net/sh_eth.h +0 -63
-
-#define TDLAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0018)
-#define RDLAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0020)
-
-#define EDMR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0000)
-#define EDTRR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0008)
-#define EDRRR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0010)
-#define EESR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0028)
-#define EESIPR(port) ? (BASE_IO_ADDR + 0x0030)
-#define TRSCER(port) ? (BASE_IO_ADDR + 0x0038)
-#define TFTR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0048)
-#define FDR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x0050)
-#define RMCR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0058)
-#define FCFTR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0070)
-#define ECMR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0100)
-#define RFLR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0108)
-#define ECSIPR(port) ? (BASE_IO_ADDR + 0x0118)
-#define PIR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x0120)
-#define APR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x0154)
-#define MPR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x0158)
-#define TPAUSER(port) ?(BASE_IO_ADDR + 0x0164)
-#define MAHR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x01c0)
-#define MALR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x01c8)
-
-#elif defined(CONFIG_CPU_SH7734)
-#define SH_ETH_TYPE_GETHER
-#define BASE_IO_ADDR ? 0xFEE00000
-
-#define EDSR(port) ? ? ? ? ? ? (BASE_IO_ADDR)
-
-#define TDLAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0010)
-#define TDFAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0014)
-#define TDFXR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0018)
-#define TDFFR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x001c)
-#define RDLAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0030)
-#define RDFAR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0034)
-#define RDFXR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0038)
-#define RDFFR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x003c)
-
-#define EDMR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0400)
-#define EDTRR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0408)
-#define EDRRR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0410)
-#define EESR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0428)
-#define EESIPR(port) ? (BASE_IO_ADDR + 0x0430)
-#define TRSCER(port) ? (BASE_IO_ADDR + 0x0438)
-#define TFTR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0448)
-#define FDR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x0450)
-#define RMCR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0458)
-#define RPADIR(port) ? (BASE_IO_ADDR + 0x0460)
-#define FCFTR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x0468)
-#define ECMR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0500)
-#define RFLR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x0508)
-#define ECSIPR(port) ? (BASE_IO_ADDR + 0x0518)
-#define PIR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x0520)
-#define PIPR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x052c)
-#define APR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x0554)
-#define MPR(port) ? ? ? ? ? ? ?(BASE_IO_ADDR + 0x0558)
-#define TPAUSER(port) ?(BASE_IO_ADDR + 0x0564)
-#define GECMR(port) ? ? ? ? ? ?(BASE_IO_ADDR + 0x05b0)
-#define MAHR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x05C0)
-#define MALR(port) ? ? ? ? ? ? (BASE_IO_ADDR + 0x05C8)
-#define RMII_MII(port) ?(BASE_IO_ADDR + 0x0790)
-

?#endif

?/*

drivers/net/sh_eth.h +25 -1
@@ -506,3 +562,28 @@ enum RPADIR_BIT {
 ?enum FIFO_SIZE_BIT {
 ? ? ? ?FIFO_SIZE_T = 0x00000700, FIFO_SIZE_R = 0x00000007,
 ?};
+
+static inline unsigned long sh_eth_reg_addr(struct sh_eth_dev *eth,
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? int enum_index)
+{
+#if defined(SH_ETH_TYPE_GETHER)
+ ? ? ? const u16 *reg_offset = sh_eth_offset_gigabit;
+#elif defined(SH_ETH_TYPE_ETHER)
+ ? ? ? const u16 *reg_offset = sh_eth_offset_fast_sh4;
+#else
+#error
+#endif
+ ? ? ? return BASE_IO_ADDR + reg_offset[enum_index] + 0x800 * eth->port;
+}
+
+static inline void sh_eth_write(struct sh_eth_dev *eth, unsigned long data,
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? int enum_index)
+{
+ ? ? ? outl(data, sh_eth_reg_addr(eth, enum_index));
+}
+
+static inline unsigned long sh_eth_read(struct sh_eth_dev *eth,
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? int enum_index)
+{
+ ? ? ? return inl(sh_eth_reg_addr(eth, enum_index));
+}
--

1.7.1

Signature · 3 lines
Nobuhiro Iwamatsu
?? iwamatsu at {nigauri.org / debian.org}
?? GPG ID: 40AD1FA6