Trouble mounting a JFFS2 fs.
Getting lots of strange error messages when trying to mount a JFFS2 file system built from OE classic 2011.03
It is built using:EXTRA_IMAGECMD_jffs2 = "--little-endian --eraseblock=0x20000 --pagesize=0x800 -n"
and programmed into the flash using u-boot "nand write".
The machine is an AT91SAM9N12 configured to use S/W ECC for U-Boot and kernel. I have tried H/W ECC before with less success.
There is one bad block in the rootfs are and there is a CRC error on the initial check, but the JFFS2 file system seems to mount, and the init routines start
to execute, but I have a feeling that the file system is mounted readonly at that stage, even though the command line says "rw".
When NFS mounting the image using the SAM9N12EK I do not have any problems.
Any clues?
BR
Ulf Samuelsson
Relevant parts of the bootlog are: (full bootlog below)
atmel_nand atmel_nand: Using dma0chan0 for DMA transfers.
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0xad, Chip ID: 0xa1 (Hynix H27S1G8F2BFR-BC)
Scanning device for bad blocks
Bad eraseblock 82 at 0x000000a40000
...jffs2_scan_dirent_node(): Node CRC failed on node at 0x00274194: Read 0x681bfdff, calculated 0x681bfddf
...
VFS: Mounted root (jffs2 filesystem) on device 31:1.
devtmpfs: mounted
Freeing init memory: 132K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
Remounting root file system...
Caching udev devnodes
Populating dev cache
logger: mount: mount point /proc/bus/usb does not exist
ALSA: Restoring mixer settings.../usr/sbin/alsactl: load_state:1625: No soundcards found...
Configuring update-modules.
Configuring ppp.
Configuring ppp-dialin.
Configuring e2fsprogs./usr/bin/update-alternatives: line 193: sed: Text file busy //usr/lib/opkg/info/e2fsprogs.postinst: line 2: update-alternatives: Text file busy
=======================================
FULL BOOT LOG
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39 (ulf@grond) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #1 Fri Jun 29 13:10:12 CEST 2012
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: AT91SAM9N12EK2
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 399 MHz, master 133 MHz, main 16.000 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61120k/61120k available, 4416k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff000000 - 0xffe00000 ( 14 MB)
vmalloc : 0xc4800000 - 0xfee00000 ( 934 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0029000 ( 132 kB)
.text : 0xc0029000 - 0xc0370000 (3356 kB)
.data : 0xc0370000 - 0xc0392320 ( 137 kB)
NR_IRQS:192
AT91: 128 gpio irqs in 4 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 199.06 BogoMIPS (lpj=995328)pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
NET: Registered protocol family 16
AT91: Power Management (with slow clock mode)
AT91: Starting after user reset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usbat_hdmac at_hdmac.0: Atmel AHB DMA Controller ( cpy slave ), 8 channels
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource tcb_clksrc
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 119
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered (default)
atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
brd: module loaded
loop: module loaded
ssc ssc.0: Atmel SSC device at 0xc4870000 (irq 28)atmel_nand atmel_nand: Using dma0chan0 for DMA transfers.
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0xad, Chip ID: 0xa1 (Hynix H27S1G8F2BFR-BC)
Scanning device for bad blocks
Bad eraseblock 82 at 0x000000a40000
Creating 2 MTD partitions on "atmel_nand":
0x000000000000-0x000000400000 : "Boot"
0x000000400000-0x000008000000 : "RootFS"atmel_spi atmel_spi.0: Using dma0chan1 (tx) and dma0chan2 (rx) for DMA transfersatmel_spi atmel_spi.0: Atmel SPI Controller at 0xf0000000 (irq 13)
enc28j60 spi0.0: enc28j60 Ethernet driver 1.01 loaded
enc28j60 spi0.0: enc28j60 chip not found
enc28j60: probe of spi0.0 failed with error -5ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driverat91_ohci at91_ohci: AT91 OHCIat91_ohci at91_ohci: new USB bus registered, assigned bus number 1at91_ohci at91_ohci: irq 22, io mem 0x00500000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
mousedev: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0at91_rtc at91_rtc: rtc core: registered at91_rtc as rtc0
AT91 Real Time Clock driver.
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key typeat91_rtc at91_rtc: setting system clock to 2007-01-01 00:09:49 UTC (1167610189)atmel_mci atmel_mci.0: Using dma0chan3 for DMA transfersatmel_mci atmel_mci.0: Atmel MCI controller at 0xf0008000 irq 12, 1 slots
usb 1-1: new full speed USB device number 2 using at91_ohcijffs2_scan_dirent_node(): Node CRC failed on node at 0x00274194: Read 0x681bfdff, calculated 0x681bfddf scsi0 : usb-storage 1-1:1.0
scsi 0:0:0:0: Direct-Access USB2.0 FlashDisk 0.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 2007039 512-byte logical blocks: (1.02 GB/979 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: detected capacity change from 0 to 1027603968
sda: sda1
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
VFS: Mounted root (jffs2 filesystem) on device 31:1.
devtmpfs: mounted
Freeing init memory: 132K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
Remounting root file system...
Caching udev devnodes
Populating dev cache
logger: mount: mount point /proc/bus/usb does not exist
ALSA: Restoring mixer settings.../usr/sbin/alsactl: load_state:1625: No soundcards found...
Configuring update-modules.
Configuring ppp.
Configuring ppp-dialin.
Configuring e2fsprogs./usr/bin/update-alternatives: line 193: sed: Text file busy //usr/lib/opkg/info/e2fsprogs.postinst: line 2: update-alternatives: Text file busy
Configuring dbus.
Configuring compat-wireless.
Configuring bluez4.
Configuring wpa-supplicant.
Configuring angstrom-libc-fixup-hack.
Configuring libnss-mdns.
Configuring avahi-daemon.
Configuring avahi-autoipd.
Collected errors:
* pkg_run_script: package "e2fsprogs" postinst script returned status 2.
* opkg_configure: e2fsprogs.postinst returned 2.
* pkg_run_script: package "dbus" postinst script returned status 255.
* opkg_configure: dbus.postinst returned 255.
* pkg_run_script: package "compat-wireless" postinst script returned status 255.
* opkg_configure: compat-wireless.postinst returned 255.
* pkg_run_script: package "bluez4" postinst script returned status 255.
* opkg_configure: bluez4.postinst returned 255.
* pkg_run_script: package "wpa-supplicant" postinst script returned status 255.
* opkg_configure: wpa-supplicant.postinst returned 255.
* pkg_run_script: package "angstrom-libc-fixup-hack" postinst script returned status 255.
* opkg_configure: angstrom-libc-fixup-hack.postinst returned 255.
* pkg_run_script: package "libnss-mdns" postinst script returned status 255.
* opkg_configure: libnss-mdns.postinst returned 255.
* pkg_run_script: package "avahi-daemon" postinst script returned status 255.
* opkg_configure: avahi-daemon.postinst returned 255.
* pkg_run_script: package "avahi-autoipd" postinst script returned status 255.
* opkg_configure: avahi-autoipd.postinst returned 255./etc/rcS.d/S40configure: line 25: rm: Text file busy/etc/init.d/rc: line 172: /etc/rcS.d/S41networking: Text file busy/etc/init.d/rc: line 172: /etc/rcS.d/S43portmap: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 23: grep: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 23: chmod: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 23: chown: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 37: /sbin/sysctl: Text file busy /etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 57: rm: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 57: ln: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 69: /etc/init.d/hwclock.sh: Text file busy /etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 79: date: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 79: cat: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 79: awk: Text file busy/etc/init.d/rc: /etc/rcS.d/S55bootmisc.sh: line 79: expr: Text file busy
sh: 1: unknown operand/etc/init.d/rc: line 172: /etc/rcS.d/S97blueprobe: Text file busy
INIT: Entering runlevel: 5
INIT: cannot execute "/etc/init.d/rc"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "S" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "S" respawning too fast: disabled for 5 minutes
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "S" respawning too fast: disabled for 5 minutes
Quoted 3 lines · Ulf Samuelsson
Getting lots of strange error messages when trying to mount a JFFS2 file system built from OE classic 2011.03
Looks like this is a udev problem.
Running 2.6.39 with udev-165.
During init, S03udev is called, and after "udevadm trigger" is called at the end, then the shell is no longer able to access anything,
When you try to execute any command, an error - "Text file busy" - is reported. Googling, revealed some minor problems in the udev, and I found
some odditied in the kernel build, but fixing those did not help out.
Have been running 2.6.39 with udev-165 using NFS from quite some time but not from a JFFS2 fs.
Any known problem with this combination?
Have to stick to this kernel, but If I upgrade to a later udev, are there any recommendations for 2.6.39?
Tried test baking the udevs in oe-core and they seem to have dependencies not available in OE classic (yet). A bit worried that they are too new as well. The 165 is the latest in the 2011.03 maintenance branch which I am based on, but in the main trunk 168 and 171 seems to be available.
BR
Ulf Samuelsson
Quoted 276 lines
It is built using:
EXTRA_IMAGECMD_jffs2= "--little-endian --eraseblock=0x20000 --pagesize=0x800 -n"and programmed into the flash using u-boot "nand write".
The machine is an AT91SAM9N12 configured to use S/W ECC for U-Boot and kernel. I have tried H/W ECC before with less success.There is one bad block in the rootfs are and there is a CRC error on the initial check, but the JFFS2 file system seems to mount, and the init routines start
to execute, but I have a feeling that the file system is mounted readonly at that stage, even though the command line says "rw".When NFS mounting the image using the SAM9N12EK I do not have any problems.
Any clues?
BR
Ulf SamuelssonRelevant parts of the bootlog are: (full bootlog below)
atmel_nandatmel_nand: Using dma0chan0 for DMA transfers.
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID:0xad, Chip ID:0xa1(Hynix H27S1G8F2BFR-BC)
Scanning device for bad blocks
Bad eraseblock 82 at0x000000a40000
...jffs2_scan_dirent_node(): Node CRC failed on node at0x00274194: Read0x681bfdff, calculated0x681bfddf
...
VFS: Mounted root (jffs2 filesystem) on device 31:1.
devtmpfs: mounted
Freeing init memory: 132K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
Remounting root file system...
Caching udev devnodes
Populating dev cache
logger: mount: mount point/proc/bus/usbdoes not exist
ALSA: Restoring mixer settings.../usr/sbin/alsactl: load_state:1625: No soundcards found...
Configuring update-modules.
Configuring ppp.
Configuring ppp-dialin.
Configuring e2fsprogs./usr/bin/update-alternatives: line 193: sed: Text file busy //usr/lib/opkg/info/e2fsprogs.postinst: line 2: update-alternatives: Text file busy=======================================
FULL BOOT LOGUncompressing Linux... done, booting the kernel.
Linux version 2.6.39 (ulf@grond) (gcc version 4.5.3 20110311 (prerelease) (GCC) ) #1 Fri Jun 29 13:10:12 CEST 2012
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: AT91SAM9N12EK2
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 399 MHz, master 133 MHz, main 16.000 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61120k/61120k available, 4416k reserved, 0K highmem
Virtual kernel memory layout:
vector :0xffff0000-0xffff1000( 4 kB)
fixmap :0xfff00000-0xfffe0000( 896 kB)
DMA :0xff000000-0xffe00000( 14 MB)
vmalloc :0xc4800000-0xfee00000( 934 MB)
lowmem :0xc0000000-0xc4000000( 64 MB)
modules :0xbf000000-0xc0000000( 16 MB)
.init :0xc0008000-0xc0029000( 132 kB)
.text :0xc0029000-0xc0370000(3356 kB)
.data :0xc0370000-0xc0392320( 137 kB)
NR_IRQS:192
AT91: 128 gpio irqs in 4 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 199.06 BogoMIPS (lpj=995328)pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
NET: Registered protocol family 16
AT91: Power Management (with slow clock mode)
AT91: Starting after user reset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usbat_hdmacat_hdmac.0: Atmel AHB DMA Controller ( cpy slave ), 8 channels
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksourcetcb_clksrc
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 119
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered (default)
atmel_usart.0: ttyS0 at MMIO0xfefff200(irq = 1) is aATMEL_SERIAL
brd: module loaded
loop: module loaded
ssc ssc.0: Atmel SSC device at0xc4870000(irq 28)atmel_nandatmel_nand: Using dma0chan0 for DMA transfers.
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID:0xad, Chip ID:0xa1(Hynix H27S1G8F2BFR-BC)
Scanning device for bad blocks
Bad eraseblock 82 at0x000000a40000
Creating 2 MTD partitions on "atmel_nand":
0x000000000000-0x000000400000 : "Boot"
0x000000400000-0x000008000000 : "RootFS"atmel_spiatmel_spi.0: Using dma0chan1 (tx) and dma0chan2 (rx) for DMA transfersatmel_spiatmel_spi.0: Atmel SPI Controller at0xf0000000(irq 13)
enc28j60 spi0.0: enc28j60 Ethernet driver 1.01 loaded
enc28j60 spi0.0: enc28j60 chip not found
enc28j60: probe of spi0.0 failed with error -5ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driverat91_ohciat91_ohci: AT91 OHCIat91_ohciat91_ohci: new USB bus registered, assigned bus number 1at91_ohciat91_ohci: irq 22, io mem0x00500000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
mousedev: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0at91_rtcat91_rtc: rtc core: registeredat91_rtcas rtc0
AT91 Real Time Clock driver.
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Registering thedns_resolverkey typeat91_rtcat91_rtc: setting system clock to 2007-01-01 00:09:49 UTC (1167610189)atmel_mciatmel_mci.0: Using dma0chan3 for DMA transfersatmel_mciatmel_mci.0: Atmel MCI controller at0xf0008000irq 12, 1 slots
usb 1-1: new full speed USB device number 2 usingat91_ohcijffs2_scan_dirent_node(): Node CRC failed on node at0x00274194: Read0x681bfdff, calculated0x681bfddfscsi0 : usb-storage 1-1:1.0
scsi 0:0:0:0: Direct-Access USB2.0 FlashDisk 0.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 2007039 512-byte logical blocks: (1.02 GB/979 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: detected capacity change from 0 to 1027603968
sda: sda1
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
VFS: Mounted root (jffs2 filesystem) on device 31:1.
devtmpfs: mounted
Freeing init memory: 132K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
Remounting root file system...
Caching udev devnodes
Populating dev cache
logger: mount: mount point/proc/bus/usbdoes not exist
ALSA: Restoring mixer settings.../usr/sbin/alsactl: load_state:1625: No soundcards found...
Configuring update-modules.
Configuring ppp.
Configuring ppp-dialin.
Configuring e2fsprogs./usr/bin/update-alternatives: line 193: sed: Text file busy //usr/lib/opkg/info/e2fsprogs.postinst: line 2: update-alternatives: Text file busy
Configuring dbus.
Configuring compat-wireless.
Configuring bluez4.
Configuring wpa-supplicant.
Configuring angstrom-libc-fixup-hack.
Configuring libnss-mdns.
Configuring avahi-daemon.
Configuring avahi-autoipd.
Collected errors:
*pkg_run_script: package "e2fsprogs" postinst script returned status 2.
*opkg_configure: e2fsprogs.postinst returned 2.
*pkg_run_script: package "dbus" postinst script returned status 255.
*opkg_configure: dbus.postinst returned 255.
*pkg_run_script: package "compat-wireless" postinst script returned status 255.
*opkg_configure: compat-wireless.postinst returned 255.
*pkg_run_script: package "bluez4" postinst script returned status 255.
*opkg_configure: bluez4.postinst returned 255.
*pkg_run_script: package "wpa-supplicant" postinst script returned status 255.
*opkg_configure: wpa-supplicant.postinst returned 255.
*pkg_run_script: package "angstrom-libc-fixup-hack" postinst script returned status 255.
*opkg_configure: angstrom-libc-fixup-hack.postinst returned 255.
*pkg_run_script: package "libnss-mdns" postinst script returned status 255.
*opkg_configure: libnss-mdns.postinst returned 255.
*pkg_run_script: package "avahi-daemon" postinst script returned status 255.
*opkg_configure: avahi-daemon.postinst returned 255.
*pkg_run_script: package "avahi-autoipd" postinst script returned status 255.
*opkg_configure: avahi-autoipd.postinst returned 255./etc/rcS.d/S40configure: line 25: rm: Text file busy/etc/init.d/rc: line 172:/etc/rcS.d/S41networking: Text file busy/etc/init.d/rc: line 172:/etc/rcS.d/S43portmap: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 23: grep: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 23: chmod: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 23: chown: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 37:/sbin/sysctl: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 57: rm: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 57: ln: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 69:/etc/init.d/hwclock.sh: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 79: date: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 79: cat: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 79: awk: Text file busy/etc/init.d/rc:/etc/rcS.d/S55bootmisc.sh: line 79: expr: Text file busy
sh: 1: unknown operand/etc/init.d/rc: line 172:/etc/rcS.d/S97blueprobe: Text file busy
INIT: Entering runlevel: 5
INIT: cannot execute "/etc/init.d/rc"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "S" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "S" respawning too fast: disabled for 5 minutes
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: cannot execute "/sbin/getty"
INIT: Id "S" respawning too fast: disabled for 5 minutes_______________________________________________
Openembedded-devel mailing list
[email protected]
http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-devel